• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.445-448
• /
• 2009

The present work deals with microstructure and tensile deformation of nanostructured dual-phase steel consisting of ferrite and martensite phases. Prior to deformation, a fully martensite phase is prepared and then processed by equal channel angular pressing (ECAP) and subsequent annealing. Room-temperature tensile properties are examined and compared to those of dual-phase steels with coarse grains. Due to the combined effects coming from the grain refinement of both phases and their uniform distributions, the nanostructured dual-phase steel exhibits better strength and ductility than coarse grained counterpart, achieving ${\sim}1\;GPa$ and ${\sim}20%$ for tensile strength and elongation, respectively.

• Journal of the Korean Ceramic Society
• /
• v.44 no.8
• /
• pp.424-429
• /
• 2007

Novel conductive $CO_2$ membranes composed of dual phases, molten carbonates and electronic conducting ceramics, were investigated. As the microstructure control of electronic conducting ceramic supports is extremely important to keep the molten carbonates stable in the membranes by a capillary force applied by the pore structure of the supports, we have scrutinized the microstructure of the electronic conducting supports utilizing microscopic images and gas permeability measurement. From the evaluation of the electrical conductivities of the molten carbonates and the electronic conducting ceramic supports, we found that the ionic conductivity of the molten carbonates could determine $CO_2$ flux through the dual phase membranes if the surface exchange rate were relatively high enough.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.172-172
• /
• 2016

Dual-beam experiments (Focused ion beam - Orientation mapping microstructure, FIB-OIM) is a widely used experimental tool because this experiments tool available alternates between automated serial sectioning and EBSD with the help of dual beams. We investigated the reconstruction procedure for analysis tool which three-dimensional internal microstructure using Ni superalloy(IN100) and ZrO2. As a results, we observed annealing twin boundary each layer in Ni superalloy(IN100) and fairly isotropic internal microstructure in ZrO2 using marching cubes algorithm. According to these results, this procedure is reconstructed well and we gained ability to arrange the EBSD map and internal microstructure.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.3
• /
• pp.133-140
• /
• 2018

This paper is concerned with the 2-D micostructure generation for $Ni-A{\ell}_2O_3$ dual-phase composite materials and the numerical analysis of mechanical characteristic of hierarchical models of microstructure which are defined in terms of the scale of microstructure. The microstructures of dual-phase composite materials were generated by applying the mathematical RMDF(random morphology description functions) technique to a 2-D RVE of composite materials. And, the hierarchical models of microstructure were defined by the number of Gaussian points. Meanwhile, the volume fractions of metal and ceramic particles were set by adjusting the level of RMD functions. The microstructures which were generated by RMDF technique are definitely random even though the total number of Gaussian points is the same. The randomly generated microstructures were applied to a 2-D beam model, and the variation of normal and shear stresses to the scale of microstructure was numerically investigated. In addition, through the crack analyses, the influence of RMDF randomness and Gauss point number on the crack-tip stress is investigated.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.315-320
• /
• 2020

This study deals with the yielding behavior and strain aging properties of three bake hardening steels with dual-phase microstructure, fabricated by varying the annealing temperature. Bake hardening and aging tests are performed to examine the correlation of martensite volume fraction with yielding behavior and strain aging properties of the bake hardening steels with dual-phase microstructure. The volume fraction of martensite increases with increasing annealing temperature. Room-temperature tensile test results show that the yielding behavior changes from discontinuous-type to continuous-type with increasing volume fraction of martensite due to higher mobile dislocation density. According to the bake hardening and aging tests, the specimen with the highest fraction of martensite exhibited high bake hardening with low aging index because solute carbon atoms in ferrite and martensite effectively diffuse to dislocations during the bake hardening test, while in the aging test they diffuse at only ferrite due to lower aging temperature.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.3
• /
• pp.223-229
• /
• 1981

A study has been made of the fracture strength and ductility of the dual phase microstructure, in which the martensitic phase encapsulated islands of ferritic phase in association with the cleavage cracking of ferrite grains. It was found the final fracture occured in a brittle manner, starting from the Griffith crack which consisted of the cleavage crack in the ferrite grains and the cracks in second phase. Furthermore, the effects of the ferrite grain sizes on the Griffith crack were also discussed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.421-424
• /
• 2007

Dry sliding wear behavior of ultra-fine grained (UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.149-152
• /
• 2006

Dry sliding wear behavior of low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the dual phase steel was compared with that of a plain carbon steel which was normalized at $950^{\circ}C$ for 30min and then air-cooled. Dry sliding wear tests were carried out using a pin-on-disk type tester at various loads of 1N to 10N under a constant sliding speed condition of 0.2m/sec against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss measured to the accuracy of $10^{-5}g$ by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and a profilomter. Micro vickers hardness values of the cross section of worn surface were measured to analyze strain hardening behavior underneath the wearing surfaces. The were rate of the dual phase steel was lower than the plain carbon steel. Oxidation on the sliding surface and strain hardening were attributed for the higher wear resistance of the dual phase steel.

• Transactions of Materials Processing
• /
• v.16 no.4 s.94
• /
• pp.299-303
• /
• 2007

Dry sliding wear behavior of ultra-fine grained(UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• Nuclear Engineering and Technology
• /
• v.45 no.6
• /
• pp.821-826
• /
• 2013

In the present study, the effects of various heat treatments on the microstructure and mechanical properties of dual phase ODS steels were investigated to enhance the high strength at elevated temperature. Dual phase ODS steels have been designed by the control of ferrite and austenite formers, i.e., Cr, W and Ni, C in Fe-based alloys. The ODS steels were fabricated by mechanical alloying and a hot isostatic pressing process. Heat treatments, including hot rolling-tempering and normalizing-tempering with air- and furnace-cooling, were carefully carried out. It was revealed that the grain size and oxide distributions of the ODS steels can be changed by heat treatment, which significantly affected the strengths at elevated temperature. Therefore, the high temperature strength of dual phase ODS steel can be enhanced by a proper heat treatment process with a good combination of ferrite grains, nano-oxide particles, and grain boundary sliding.