• Computers and Concrete
• /
• v.31 no.5
• /
• pp.385-394
• /
• 2023

Displacement is an important element for evaluating the stability and failure mechanism of hydraulic structures. Digital image correlation (DIC) is a useful technique to measure a three-dimensional displacement field using two cameras without any contact with test material. The objective of this study is to evaluate the behavior of stacked geotextile tubes using the DIC technique. Geotextile tubes are stacked to build a small-scale temporary dam model to exclude water from a specific area. The horizontal and vertical displacements of four stacked geotextile tubes are monitored using a dual camera system according to the upstream water level. The geotextile tubes are prepared with two different fill materials. For each dam model, the interface layers between upper and lower geotextile tubes are either unreinforced or reinforced with a cementitious binder. The displacement of stacked geotextile tubes is measured to analyze the behavior of geotextile tubes. Experimental results show that as upstream water level increases, horizontal and vertical displacements at each layer of geotextile tubes initially increase with water level, and then remain almost constant until the subsequent water level. The displacement of stacked geotextile tubes depends on the type of fill material and interfacial reinforcement with a cementitious binder. Thus, the proposed DIC technique can be effectively used to evaluate the behavior of a hydraulic structure, which consists of geotextile tubes.

• Journal of Biomedical Engineering Research
• /
• v.44 no.6
• /
• pp.392-403
• /
• 2023

This study presents a new hybrid fNIRS-EEG system to meet the demand for a lightweight and low-cost sleep pattern monitoring device. For multiple-channel configuration, a six-channel electroencephalogram (EEG) and a functional near-infrared spectroscopy (fNIRS) system with eight photodiodes (PD) and four dual-wavelength LEDs are designed. To enhance the convenience of signal measurement, the device is miniaturized into a patch-like form, enabling simultaneous measurement on the forehead. Due to its fully integrated functionality, the developed system is advantageous for performing sleep stage classification with high-temporal and spatial resolution data. This can be realized by utilizing a two-dimensional (2D) brain activation map based on the concentration changes in oxyhemoglobin and deoxyhemoglobin during sleep stage transitions. For the system verification, the phantom model with known optical properties was tested at first, and then the sleep experiment for a human subject was conducted. The experimental results show that the developed system qualifies as a portable hybrid fNIRS-EEG sleep pattern monitoring device.

• Restorative Dentistry and Endodontics
• /
• v.32 no.3
• /
• pp.169-179
• /
• 2007

This study was to compare the microshear bond strength $({\mu}SBS)$ of light- and chemically cured composites to enamel coupled with four 2-step self-etch adhesives and also to evaluate the incompatibility between 2-step self-etch adhesives and chemically cured composite resin. Crown segments of extracted human molars were cut mesiodistally, and a 1 mm thickness of specimen was made. They were assigned to four groups by adhesives used: SE group (Clearfil SE Bond) AdheSE group (AdheSE), Tyrian group (Tyrian SPE/One-Step Plus), and Contax group (Contax) Each adhesive was applied to a cut enamel surface as per the manufacturer's instruction. Light-cured (Filtek Z250) or chemically cured composite (Luxacore Smartmix Dual) was bonded to the enamel of each specimen using a Tygon tube. After storage in distilled water for 24 hours, the bonded specimens were subjected to ${\mu}SBS$ testing with a crosshead speed of 1 mm/minute. The mean ${\mu}SBS$ (n=20 for each group) was statistically compared using two-way ANOVA, Tukey HSD, and t test at 95% level. Also the interface of enamel and composite was evaluated under FE-SEM. The results of this study were as follows ; 1. The ${\mu}SBS$ of the SE Bond group to the enamel was significantly higher than that of the AdheSE group, the Tyrian group, and the Contax group in both the light-cured and the chemically cured composite resin (p < 0.05). 2. There was not a significant difference among the hdheSE group, the Tyrian group, and the Contax group in both the light-cured and the chemically cured composite resin. 3. The ${\mu}SBS$ of the light-cured composite resin was significantly higher than that of the chemically cured composite resin when same adhesive was applied to the enamel (p < 0.05). 4. The interface of enamel and all 2-step self-etch adhesives showed close adaptation, and so the incompatibility of the chemically cured composite resin did not show.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8933-8939
• /
• 2015

In this paper, we designed a multi humanoid robot control method for performing an exhibition that will maximize the efficiency and user convenience and implementation. In recent years, an increasing number of case and to take advantage of the robots in the field performances and exhibitions, plays, musicals, orchestra performances are also various genres. In concert with the existing small humanoid exhibition to source from outside by using a computer and MP3 player and play, while pressing the start button of communication equipment for the show to start the robot began performing with the zoom. Thus, due to the dual source and robot operation and synchronization does not work well is the synchronization of the start of the concert sound starting point of the robot and robot motion and sound are reproduced separately were frequently occurs when you need to restart the show. In addition, when the center of gravity or lose the robots who were present during the performance problems such as performance or intervene to restart the show. In order to overcome this, in this paper, Multi-small humanoid robot was designed to control the efficiency and the user of the GUI-based human interface S/W to maximize convenience, Zigbee communication to transmit a plurality of data in al small humanoid It was used. In addition, targeting a number of the small humanoid robot demonstrated the effectiveness and validity of the user's convenience by gender actual implementation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.1
• /
• pp.36-44
• /
• 2007

This paper presented a hybrid ternary encoding scheme using 3-valued logic. It can adapt to the delay-insensitive(DI) model. We designed an asynchronous wrapper for the hybrid ternary encoding scheme to communicate with various asynchronous encoding schemes. It reduced about 50% of transmission lines and power consumption compared with the conventional 1-of-4 and ternary encoding scheme. The proposed wrappers were designed and simulated using the $0.18-{\mu}m$ standard CMOS technology. As a result, the asynchronous wrapper operated over 2 GHz communicating with a system bus. Moreover, the power dissipation of the system bus adapted the hybrid ternary encoding logic decreases 65%, 43%, and 36% of the dual-rail, 1-of-4, and ternary encoding scheme, respectively. The proposed data encoding scheme and the wrapper circuit can be useful for asynchronous high-speed and low-power asynchronous interface.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.24-33
• /
• 2000

Switching behaviour of the ferroelectric thin film and device characteristics of the MFSFET(Metal-Ferroelectric-Semiconductor FET) are simulated with taking into account the accumulation of oxygen vacancies near interface between the ferroelectric thin film and the bottom electrode caused by the progress of fatigue. In our switching model, relative switched charge is 0.74 nC before fatigue, but after the progress of fatigue it reduces to 0.15 nC with the generation of oxygen vacancies. It indicates that the generation of oxygen vacancies strongly suppresses polarization reversal. $C-V_G\;and\;I_D-V_G$ curves in our MFSFET device model exhibit the memory window of 2 V and show the accumulation, the depletion and the inversion regions in capacitance characteristic clearly. The difference of saturation drain current of the device before fatigue in shown by the dual threshold voltages in $I_D-V_G$ curve as 6nA/$cm^2$ and decreases as much as 50% after fatigue. Decrease of the difference of saturation drain currents by fatigue implies that the accumulation of oxygen vacancies with the fatigue should be avoided in the device application. Our simulation model is expected to play an important role in estimation of the behavior of MFSFET device with various ferroelectric thin films.

• Journal of Navigation and Port Research
• /
• v.33 no.10
• /
• pp.691-697
• /
• 2009

Hardware dedicated off-the-shelf maritime differential GPS RSIM lacks the open architecture to meet all the minimum maritime user requirements and to include future GNSS improvements after recapitalization. This paper carries out a study to replace existing hardware dedicated differential GPS RSIM with software differential GPS RSIM in order to make up the weak point of hardware dedicated off-the-shelf maritime differential GPS RSIM. In this paper, the architecture of software RSIM is proposed for maritime DGPS recapitalization. And the feasibility analysis of the proposed software differential GPS RSIM is performed as the first phase to realize the proposed architecture. For the feasibility analysis, the prototype RF module and DSP module are implemented with properties as wide RF bandwidth, high sampling frequency, and high speed transmission interface. This paper shows that the proposed architecture has the possibility of real time operation of software RSIM functionality onto the PC-based platform through the analysis of computation time. Finally, this paper verifies that the L1/L2 dual frequency software differential RSIM designed according to the proposed method satisfies the performance specifications set out in RTCM paper 221-2006-SC104-STD.

• The Korean Journal of Malacology
• /
• v.20 no.2
• /
• pp.165-169
• /
• 2004

The BLAST server for the mollusk was constructed on the basis of the Intel Server Platform SC-5250 dual Xeon 2.8 GHz cpu and Linux operating system. After establishing the operating system, we installed NCBI (National Center for Biotechnology Information) WebBLAST package after web server configuration for cgi (common gate interface) (http://chimp.kribb.re.kr/mollusks). To build up the stand alone blast, we conducted as follows: First, we downloaded the genome information (mitochondria genome information), DNA sequences, amino acid sequences related with mollusk available at NCBI. Second, it was translated into the multifasta format that was stored as database by using the formatdb program provided by NCBI. Finally, the cgi was used for the Stand Alone Blast server. In addition, we have added the vector, Escherichia coli, and repeat sequences into the server to confirm a potential contamination. Finally, primer3 program is also installed for the users to design the primer. The stand alone BLAST gave us several advantages: (1) we can get only the data that agree with the nucleotide sequence directly related with the mollusks when we are searching BLAST; (2) it will be very convenient to confirm contamination when we made the cDNA or genomic library from mollusks; (3) Compared to the current NSBI, we can quickly get the BLAST results on the mollusks sequence information.

• Journal of Korean Neurosurgical Society
• /
• v.62 no.4
• /
• pp.442-449
• /
• 2019

Objective : Bone mineral density (BMD) is an important consideration during fusion surgery. Although dual X-ray absorptiometry is considered as the gold standard for assessing BMD, quantitative computed tomography (QCT) provides more accurate data in spine osteoporosis. However, QCT has the disadvantage of additional radiation hazard and cost. The present study was to demonstrate the utility of artificial intelligence and machine learning algorithm for assessing osteoporosis using Hounsfield units (HU) of preoperative lumbar CT coupling with data of QCT. Methods : We reviewed 70 patients undergoing both QCT and conventional lumbar CT for spine surgery. The T-scores of 198 lumbar vertebra was assessed in QCT and the HU of vertebral body at the same level were measured in conventional CT by the picture archiving and communication system (PACS) system. A multiple regression algorithm was applied to predict the T-score using three independent variables (age, sex, and HU of vertebral body on conventional CT) coupling with T-score of QCT. Next, a logistic regression algorithm was applied to predict osteoporotic or non-osteoporotic vertebra. The Tensor flow and Python were used as the machine learning tools. The Tensor flow user interface developed in our institute was used for easy code generation. Results : The predictive model with multiple regression algorithm estimated similar T-scores with data of QCT. HU demonstrates the similar results as QCT without the discordance in only one non-osteoporotic vertebra that indicated osteoporosis. From the training set, the predictive model classified the lumbar vertebra into two groups (osteoporotic vs. non-osteoporotic spine) with 88.0% accuracy. In a test set of 40 vertebrae, classification accuracy was 92.5% when the learning rate was 0.0001 (precision, 0.939; recall, 0.969; F1 score, 0.954; area under the curve, 0.900). Conclusion : This study is a simple machine learning model applicable in the spine research field. The machine learning model can predict the T-score and osteoporotic vertebrae solely by measuring the HU of conventional CT, and this would help spine surgeons not to under-estimate the osteoporotic spine preoperatively. If applied to a bigger data set, we believe the predictive accuracy of our model will further increase. We propose that machine learning is an important modality of the medical research field.