• Journal of Life Science
• /
• v.27 no.7
• /
• pp.754-759
• /
• 2017

The 100 l culture system was made on the basis of LED light, and Nannochloropsis oculata was cultured in f/2 medium at light intensity ($100{\mu}mol/m^2/s$), culture temperature ($20^{\circ}C{\pm}1^{\circ}C$) and LD cycle (12hr). As a result, the maximum biomass of 1.07 g/l was cultured as a result of 100 l mass culture at $100{\mu}mol/m^2/s$ and 24 mg/l nitrate concentration in LED blue (475 nm). The extraction was carried out using sonicator, homogenizer and chemical method 0.5M HCl shredding method. The contents of chlorophyll a, chlorophyll b and carotenoid were 1.6, 0.5 and 0.3 mg/g cell. When using homogenizer, it was measured at 1.0, 0.6 and 0.2 mg/g cell. The chemical breakdown method of 0.5M HCl, chlorophyll a, b, and carotenoid contents were measured as 0.9, 0.8, 0 mg/g cell. The highest amount of biomass during the distruption time was measured at 3.6 mg/g cell at 15 min disintegration and acetone, 3.6 mg/g cell of acetone, methanol, and ethanol were measured as effective solvents. Concentration was measured by using microfilter, disk type continuous centrifuge and tubular type continuous centrifuge were 16.0, 1.1 and 0.5 g/l, respectively. Four kinds of equipment such as hot air dryer, vacuum dryer, spray dryer and freeze dryer were tested to optimize the drying process. As a result, the recovery rates of spray dryer and freeze dryer were 80% and 60%.

• Journal of Korean Medical classics
• /
• v.23 no.2
• /
• pp.205-223
• /
• 2010

In Korean Traditional Medicine(abbreviated to K.T.M.), hyperhidrosis and anhidrosis are the targets of the medical treatment. Furthermore sweating appearance is also one of the important symptoms which explain a particular situation of the patient in K.T.M. And at "Sanghanron(傷寒論)" which is a traditional chief clinical bible written by Jang Gi(張機) later Han dynasty(漢代) in China made full use of the various kinds of diaphoresis[汗法] as a main medical treatment with purgation therapy[下法] and emetic therapy[吐法]. So the sweat in itself not only is the disease, but also is one of the symptoms explain a disease pattern. This thesis inquires into "Hwangjenaegyeong(黃帝內經)" referring to sweat which is the origin of recognition to the sweat in K.T.M. Some theses similar to this research had been made progresses and already reported, but most of them have classified the contents into biology, pathology, diagnosis, treatment after the model of western medical theory. In the aspect of comparative studying with other literature and clinic practical using, we found characteristics of referring to sweat in "Hwangjenaegyeong(黃帝內經)". And we classify the characteristics into some categories as follows. 1. There are some terms which make a title including sweat and symbolize the characteristics, for example sweat of soul[魄汗], sweat of death[絶汗], sweat of streaming[灌汗], sweat of weakness[白汗], sweat of sleep[寢汗], sweat of bright and heat[炅汗], sweat of kidney[腎汗], sweat of escaping[漉汗], cold sweat[寒汗], sweat on the head[頭汗], hyperhidrosis[多汗], heavy sweat[大汗]. But there aren't spontaneous sweat[自汗] or sweat like a thief[盜汗] which are the normal terms referring to sweat in history of K.T.M. And there are several descriptions about sweat appearance such as sweating in half of body[汗出偏沮], sweating in the rear end and thigh and knee[汗出尻陰股膝], hyperhidrosis in the neck and aversion to wind[頸多汗惡風], hyperhidrosis in the head and face and aversion to wind[頭面多汗惡風], cannot stopping the sweating under head[頭以下汗出不可止], make a person sweat to one's feet[令汗出至足], sweating like escaping[漯漯然汗出], sweating like soaking[汗出如浴], sweating become moist[汗出溱溱], hardly escaping sweat[汗大泄], escaping sweating[漉漉之汗], sweat moisten the pores [汗濡玄府], ceaseless sweating like pouring[汗注不休] sweating like pouring and vexation[汗注煩心], damp with sweat[汗汗然], sweating spontaneously[汗且自出], removal of fever with sweat drying[熱去汗稀]. That can be divided into sweat region and sweat form. 2. There are detailed explanations of the principle of perspirations caused by hot weather, hot food, hard working and meeting damp pathogen. 3. There are some explanations of the principle of removing fever due to the excessive heat from internal and external body through sweating by replenishing the body fluid. And many descriptions about overcoming the febrile disease by dropping temperature through sweating and many diaphoresis for curing. 4. There are some descriptions about five Jang organs perspirations and attachment of five mucous body fluid to five Jang organs. 5. There are pathogenic progresses after sweating affected by the Six Atmospheric Influences and water. And detailed explanations of disease mechanism a sweat leading to another disease. 6. There are descriptions about various sweat absent situations.

• Journal of Life Science
• /
• v.23 no.3
• /
• pp.426-431
• /
• 2013

With the objective of developing a functional food source, we established optimal processing conditions for the larvae of Allomyrina dichotoma, which have been used in traditional medicine to treat hepatic disorders in Korea. Without suitable processing, the larvae are difficult to consume as a food because of their disgusting taste and smell; moreover, in this form they might be a potential microbial hazard. In this study, we investigated the effect of feeding material, sterilization, and powdering after freeze-drying on the food quality of the larvae of A. dichotoma and on cytotoxicity against Raw 264.7 cells. Three to five days feeding with the sawdust from discarded oak-trees is sufficient for the breeding process. The sawdust was sterilized by vapor for five minutes. Sterilization of the larvae at a high temperature ($115^{\circ}C$ for 5 min, 0.9 $kgf/cm^2$) is necessary to eliminate pathogenic bacteria and fungi. The results of the cytotoxicity assay showed no toxicity in the prepared extract from larvae of A. dichotoma. In addition, to prepare the larvae for human consumption, various feeds were used and the smell, color, and taste were evaluated. Our results suggested that larvae of A. dichotoma could be developed as food source when a suitable processing method is established.

• Journal of Conservation Science
• /
• v.30 no.3
• /
• pp.263-275
• /
• 2014

It's shown how to proceed the study on Manufacturing techniques & Conservation to the Iron Pot from Cheonmachong Ancient Tomb(the 155th Tomb in Hwangnam-dong). In order to investigate manufacturing techniques of the Iron Pot, some parts of the relic were gathered. After mounting, polishing and etching on the relic, analyzing the metal microstructure was conducted. Also it's conducted a SEM-EDS analysis on the nonmetallic inclusion. White iron structure was observed in the metallurgical structure inspection, SEM-EDS analysis. It seems to be dried slowly at room temperature after casting, doesn't look as particular heat treatment to improve brittleness. It is estimated that it's as the handle seam side were verified about 3cm inch wide, 1.5 thick in center of body, so 2 separate half-completed products was cast with width-type mould. The manufacturing techniques Using white cast iron structure, width-type mould are observable to the Iron Pot excavated from Sikrichong Ancient Tomb & Hwangnamdaechong grand Ancient Tomb around those were constructed the same time. It's able to recognize that it's almost identical manufacturing techniques at that time. Conservation is generically following those are survey of pretreatment, foreign material removal, stabilization, restoration and color matching in the order. cleaning & drying were added to the process as occasion demands. The strengthening treatment were difficult with artifact's volume, low concentration Paraloid NAD-10 solution was spread two or three times with a brush, surface hardening also came up with 15wt% Paraloid NAD-10 solution after the conservation was complete. There were connection & restoration for the restoration to the damage after modeling forms that it's similar to damaged parts by using the Fiber Reinforced Plastic resins(POLYCOAT FH-245, mold laminated type). Throughout this research, capitalizing on accumulations of measurements about the production technique of Iron Pot in the time of the fifth and 6th centuries is no less important than the Iron artifact's conservation for a better study in the future.

• Journal of Korean Society of Forest Science
• /
• v.78 no.3
• /
• pp.314-322
• /
• 1989

For the improvement of nursery condition and the study of eco-physiological characteristics of Pinus koraiensis(2-2) seedlings, the primary productivity was investigated and the growth characteristics and their correlationship were analyzed from May to September in 1987. Seedlings used in this study were grown at the nursery of Experimental Forestry of Kyung Hee Univ. The installation of experimental plots were divided into control plot (100%), 63%, 37% and 19% relative light intensity, and each relative light intensity plots were split into $15{\times}15/m^2$, $12{\times}12/m^2$, $9{\times}9/m^2$ and $6{\times}6/m^2$ plnting density by randomized black design method. To take into account the edge effect of plant population, material were selected from each plot by random sampling at 30 days interval. Each sampled material was divided into leaf and stem drived in a drying oven at the temperature of $85^{\circ}C$ until it had constant weight and weighed. and leaf area was surveyed. Growth analysis for RGR and NAR was done by Blackman method and correlation coefficient were investigated between RGR and NAR by analyzing the dry matter production and growth characteristics of the material, cultivated on the experimental nursery under the condition of different treatment the obtained result were as follows : 1. The increasing rate of dry matter was similar at early stage of growth, but not at late stage. 2. Leaf area growth was the maximum value at 63% relative light intensity and the minimum at 19% RLI 3. The value of RGR was the highest on June under $6{\times}6/m^2$ planting density in 63% relative light intensity, the lowest on September under $12{\times}12/m^2$ of 19% relative light intensity. 4. The change NAR decreased in early stage of growth, while it increased on August and September, The value of RGR on June under $6{\times}6/m^2$ planting density in 100 light intensity was the highest, and on September under $12{\times}12/m^2$ planting density in 19% relative light intensity was the lowest. 5. Regression and correlation between RGR and NAR showed significantly positive.

• Asian Journal of Turfgrass Science
• /
• v.24 no.1
• /
• pp.45-49
• /
• 2010

Research on nitrate-nitrogen ($NO_3-N$) leaching in turfgrass indicates that in most cases leaching poses minimal risk to the environment. Although there have been many studies investigating $NO_3-N$ leaching, there has been little research to investigate the effect of compaction level and rootzone mix on nitrogen (N) leaching. The research objective is to determine the effect of compaction level and rootzone mix on nitrogen leaching. The four rootzone mixes are 76.0:24.0, 80.8:19.2, 87.0:13.0 and 93.7:6.3 % (sand:soil). The four levels of compaction energies are 1.6, 3.0, 6.1, and 9.1 J $cm^{-2}$. Nitrogen was applied using urea at a rate of 147 kg $ha^{-1}$ split among three applications. Rootzone was packed into a polyvinylchloride pipe with a perforated bottom to facilitate drainage. Rootzone depth was 30 cm over a 5 cm gravel layer. Each column was sodded with Poa pratensis L. Hoagland solution designed for coolseason grasses, minus N, was used to ensure adequate nutrition in the rootzone. Turf grass quality and clipping yield were recorded from each tube at two-week intervals. The clippings were oven-dried at a temperature of $67^{\circ}C$ for 24 h and weighed. At the end of the study, root dry weight was determined by washing and oven-drying samples at $67^{\circ}C$ for 24 h. Leachate solution was collected weekly for analysis. More than 6.1 J $cm^{-2}$ of compaction energy increased possibilities of surface runoff. The compaction energy between 3.0 and 6.1 J $cm^{-2}$ produced more clipping dry weight and less N leaching than 9.1 J $cm^{-2}$.

• Journal of Animal Environmental Science
• /
• v.13 no.3
• /
• pp.211-218
• /
• 2007

This study was carried out to develop the technique for manufacturing activated carbon from livestock manure and to analyse it's odor absorptiveness. Each of layer manure(LM), litter from broiler house(BL) and litter from dairy barn(DL), compost from layer manure(LC) and pig manure(PC), and coconut shell(CS) was used as a raw material. Activated carbon by grinding the raw material, adding the coal tar as a binder, palletizing, drying, heating with $N_2$ gas at $400^{\circ}C$ for 1 hour, activating by reaction with steam at a temperature of $750^{\circ}C$ for 1 hour. Moisture contents of raw material was 44.9% in layer compost, 71.9% in layer manure, 24.4% in broiler litter, 47% in pig manure compost and 33.9% in dairy litter. Volatile matter in layer compost, layer manure, broiler litter, pig manure compost and dairy litter was 18.8%, 31.0%, 49.8%, 22.3% and 11.6%, respectively. Surface area(BET) of activated carbon from layer compost, layer manure, broiler litter, pig manure compost, dairy litter and coconut shell was 259.8, 209.8, 63.5, 442.3, 812.9 and $1,040\;m^2/g$, respectively. Activated carbon made by livestock manure or litter were examined with scanning electron microscope, and micropore was a type of sponge like particles honeycombed with chambers. Pore size of activated carbon was ranged from 0.39 to $5.02\;{\AA}$, but coconut shell was $0.30\;{\AA}$. Iodine absorptiveness of activated carbon from livestock manure was $530{\sim}580mg/g$. But activated carbon made by coconut shell was 1000 mg/g. Each activated carbon could absorb odor compound very well. Absorptiveness of activated carbon from layer manure for hydrogen sulfide and trimethyl amino was 74.5% and 73.9% at the accumulated flux of 60,000 ml, but, in the case of ammonia was only 15.2% at the accumulated flux of 10,000 ml

• Korean journal of food and cookery science
• /
• v.30 no.6
• /
• pp.670-678
• /
• 2014

The purpose of this study was to find the optimal swelling method and condition for seacucumber to improve its taste and texture to accomodate the rapid increase of consumption. Another purpose was to try to determine an easy way to soak dried sea-cucumber under different conditions, and identify the influence of swelling time on the texture of sea-cucumber, in order to reduce preparation time and provide basic data for easy handling. After boiling or steaming for six different periods including 5, 15, 30 and 60 minutes the texture of the sea-cucumbers were compared, For the additive test, the sea-cucumbers were boiling for 30 minutes period with 4 different additives and the textures were compared, Since the texture is an important characteristic of sea-cucumber, there are many variables that affect this property including the, drying and preservation methods. This study provides basic understanding of the influence of the heating method, time and temperature on the swelling of sea-cucumber for handy use at processing sites.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.170-187
• /
• 2020

Dolmens bearing the burial layout and stone coffin tombs of the late Bronze Age were excavated from Samdeok-ri, Goseong, Gyeonsangnsamdo, and grave items such as red-burnished pottery, arrowheads, and stone swords were also discovered. In the case of the red-burnished pottery that was found, it retains a pigment layer with a thickness of about 50 to 160㎛, but with most of the other items, exfoliation and peeling-off of pigment layers can be observed on the surface. The raw materials of the red-burnished pottery contained moderately sorted minerals such as quartz, feldspar, and hornblende, and partly opaque iron oxide minerals were also identified. In particular, the raw materials of the red-burnished pottery from stone coffin tomb #6 were different from those of the other pottery, containing large amounts of hornblende and feldspar. The pottery's red pigment was identified as hematite and showed similar mineral content of raw materials such as fine grained quartz, feldspar, and hornblende. The firing temperature is estimated to have been approximately 900℃, based on their mineral phase. The possibility exists that the raw materials had been collected from the Samdeok-ri area, because diorite and granite diorite with dominant feldspar and hornblende have been identified within 3km of that area. During the pottery manufacturing process, it is estimated that the pigment was painted on the entire surface of the red-burnished pottery after it had been molded and then finished using the abrasion technique. In other words, the red-burnished pottery was made by the process of vessel forming - semi drying - coloring - polishing. The surface and cross-section of the pottery appears differently depending on the concentration of the pigment and the coloring method used after vessels were formed. Most of the excavated pottery features a distinct boundary between pigment and body fabric. However, in the case of pottery in which fine-grained pigments penetrate the body fabric so that layers cannot be distinguished, there is the possibility that the fine-grained pigment layer was applied at a low concentration or immediately after vessel forming. Many cracks can be seen on the surface pigments in thickly painted pottery items, and in many cases, only a small portion of the pigment layers remain due to surface exfoliation and abrasion in the burial environment. It is reported that pottery items may be more easily damaged by abrasion if coated with pigment and polished, so it is believed that the red-burnished pottery of the Samdeok-ri site suffered from weathering in the burial environment. This damage was more extensive in the potsherds that were scattered outside the tomb.

• Korean Journal of Environment and Ecology
• /
• v.37 no.1
• /
• pp.1-12
• /
• 2023

We analyzed the distribution area of debris slopes in Mudeungsan (Mt. Mudeung) National Park by comparing aerial photos of the past (1966) and the present (2017) and identified the vegetation characteristics that affect the change in the area of the debris slopes by investigating the vegetation status of the debris slopes and the surrounding areas. The area of debris slopes in Mt. Mudeung appears to have been reduced to a quarter of what it used to be. Debris slopes here have decreased at an average rate of 2.3 ha/yr over 51 years by vegetation covers. Notably, most of the small-area debris slopes in the low-inclination slopes disappeared due to active vegetation coverage. However, there are still west-facing, south-west-facing, south-facing, and large-area debris slopes remaining because the sun's radiant heat rapidly raises the surface temperature of rock blocks and dries moisture, making tree growth unfavorable. Because of these locational characteristics, the small-scale vegetation in the middle of Deoksan Stony Slope, which is the broadest area, showed distinct characteristics from the adjacent forest areas. Sunny places and tree species with excellent drying resistance were observed frequently in Deoksan Stony Slope. However, tree species with high hygropreference that grow well in valleys with good soil conditions also prevailed. In some of these places, the soil layer has been well developed due to the accumulation of fine materials and organic matter between the crevices of the rock blocks, which is likely to have provided favorable conditions for such tree species to settle and grow. At the top of Mt. Mudeung, on the other hand, the forest covered the debris slopes, where Mongolian oaks (Quercus mongolica) and royal azaleas (Rhododendron schlippenbachii), which typically grow in the highlands, prevailed. This area was considered favorable for the development of vegetation for the highlands because the density of rock blocks was lower than in Deoksan Stony Slope, and the soil was exposed. Moreover, ash trees (Fraxinus rhynchophylla) and Korean maple trees (Acer pseudosieboldianum) that commonly appear in the valley areas were dominant here. It is probably due to the increased moisture content in the soil, which resulted from creating a depressive landform with a concave shape that is easy to collect rainwater as rock blocks in some areas fell and piled up in the lower region. In conclusion, the area, density of the rock blocks, and distribution pattern of rock block slopes would have affected the vegetation development and species composition in the debris slope landform.