• Corrosion Science and Technology
• /
• 제3권6호
• /
• pp.251-256
• /
• 2004

Exposure of zinc samples in simulated acid rain solution (SARS) was investigated under a periodic wet-dry conditions using an AC impedance technique. The periodic wet and dry exposure consisted of the immersion of zinc samples in SARS for one hour followed by exposure to 7 hours drying at 60% RH. Phases of the corrosion products were indentified by X-ray diffraction (XRD). The influence of relative humdiity (RH), temperature, and surface inclination on the atmospheric corrosion of zinc is described. The reciprocal of polarization resistance (1/Rp) decreases rapidly during the initial stages then slowly and eventually attains a steady state as exposure time progresses. The average of reciprocal of polarization resistance per cycle, (ARPR) was calculated and found to decrease as number of exposure cycle increases. An increase of temperature enhances the corrsion rate of zinc. The values of ARPR, of a sample inclined at 30 o are lower than those for a sample oriented horizontally. The experiment result shows a pronounced dependence of reciprocal of polarization resistance on RH. Exposure in the presence of carbonate anions gives rise to more protective corrosion products than in nitrate anion solution. The corrosion mechanism during the initial stages of atmospheric zinc corrosion under wet-dry cyclic conditions is suggested.

• 약학회지
• /
• 제33권2호
• /
• pp.111-117
• /
• 1989

The optimum reaction conditions for the acid consuming capacity of aluminum silicate synthesized from the reaction of sodium silicate solution and potassium aluminum sulfate solution were investigated by Box-Wilson experimental design, and the micromeritic properties were examined by the means of BET $N_2$ adsorption, Hg penetrometer and methylen blue adsorption. The chemical composition of the samples were analyzed by gravitic method. The results were found to be as follows: optimum reaction temperature $54.7^{\circ}C$, both concentrations of reactant soln 15.7%, reactants molar ratio (Al/Si) 0.5 and drying temperature $65.0^{\circ}C$. The acid consuming capacity of the sample prepared by above optimum conditions was 68 ml and the chemical composition was $Al_2O_3{\cdot}3.6SiO_2{\cdot}3H_2O$. The relationship between acid consuming capacity and micromeritic properties could not found in the range of experiments. Therefore, it is assumed that the acid consuming mechanism of aluminum silicate depends on the neutralization of $Al_2O_3$ and buffer action of $SiO_2$ in sample.

• 펄프종이기술
• /
• 제32권5호
• /
• pp.1-7
• /
• 2000

Alkaline Sizing behavior and mechanism of handsheets, which were prepared from thermomechanical pulp (TMP) with alkylketene dimer (AKD), were studied in terms of the conditions of the handsheet-making. AKD content in the TMP handsheets was increased with increasing of AKD addition level and the addition of a polyamideamine-epichlorohydrin resin (PAE) clearly enhanced AKD retention as well as the resultant sizing performance of TMP handsheets. Although drying of the AKD sized TMP webs at $20^{\circ}C$ led to no or quite low sizing level, but TMP handsheets sized with AKD had higher sizing degrees with increasing of the temperature of heat treatment. Scanning electron microscopic observations of the AKD-sized TMP handsheets showed that AKD emulsion particles were present on pulp fiber surfaces independently without coagulation in the TMP handsheets dried at $20^{\circ}C$. Heat treatment of the AKD-sized handsheets resulted in disappearance of the AKD emulsion particles because of their melting and spreading. The addition of calcium carbonate filler to the TMP suspensions did not influence on AKD content in the TMP handsheets. Nevertheless, their sizing degrees clearly increased by the addition of $CaCO_3$filler. Probably, AKD molecules adsorbed on the $CaCO_3$filler particles contribute to the enhancement of sizing performance. Thus, AKD can give sizing features effectively to the TMP handsheets, when they are made under suitable conditions.

• Korean Chemical Engineering Research
• /
• 제50권5호
• /
• pp.850-859
• /
• 2012

목질계 바이오매스의 가스화 및 열분해 공정에서 탈휘발 과정은 매우 중요한 메커니즘 중의 하나이며, 공정 설계 시 반드시 반영되어야 한다. 바이오매스 입자의 탈휘발에 대한 많은 경험식이 존재하지만, 다양한 특성의 바이오매스를 특정 실험조건에서 도출한 경험식에 의존하기는 힘들다. 본 연구는 유동층 가스화 분위기에서의 바이오매스 단일 입자의 탈휘발 과정을 수학적 모델을 통하여 예측하였다. 모델은 다양한 형태의 입자를 구형태로 변환한 뒤, 입자 내부의 drying, shrinkage, heat generation을 고려하여 1차원으로 해석하였다. 또한 탈휘발 과정에 영향을 주는 입자의 크기, 반응온도, 초기 수분함량, 열전달 계수, 반응모델 등 다양한 변수에 대한 변화를 관찰하였다. 탈휘발 완료시간은 입자의 크기가 커질수록, 초기 수분함량이 높을수록 증가하였으며, 반응온도가 높을수록 선형적으로 감소하였다. 또한 외부 열전달 계수가 300 $W/m^2K$ 이상일 경우 큰 변화는 나타나지 않았지만, 입자의 크기가 작을수록 외부 열전달 계수의 영향은 크게 나타났다. 모델 예측값과 문헌의 실험값은 대체로 비슷한 경향을 나타내었으며, 오차 ${\pm}10%$ 이내로 근접하였다.

• 한국의류학회지
• /
• 제41권1호
• /
• pp.84-97
• /
• 2017

Water vapor and thermal transmission properties of high emotional garments are important to evaluate wear comfort; in addition, the measuring methods of these properties are also critical for breathable and warm suit fabrics. In this study, the water vapor and thermal properties of composite yarn fabrics made of CoolMax, Tencel, and Bamboo fibers with filaments were measured and compared according to the measuring method. Water Vapor Transmittance (WVT) of the fabric woven by the sheath/core composite yarn in the warp direction was the highest due to the small staple fiber volume in the sheath/core yarn structure and high air voids in the sheath/core yarn fabrics. This property was also the highest in fabrics woven by bamboo staple yarns in the weft direction, and was the lowest on hi-multi filament fabrics. However, water vapor resistance ($R_{ef}$) of these fabrics by KSK ISO 11092 showed the opposite results to the water vapor transmittance method ($CaCl_2$ method); in addition, its correlation coefficient was low. The correlation coefficient between $R_{ef}$ and the drying rate was 0.719; therefore, the measurement mechanism of $R_{ef}$ is analogous to the drying property measurement. The thermal conductivity of the fabrics woven with compact staple yarn showed a high value; however, the hi-multi filament fabric showed low thermal conductivity. Therefore, fiber characteristics affect thermal properties more than yarn structure. The correlation between thermal property and moisture transport was also low. This study showed that: water vapor transmittance was active at the loose yarn structure, dry heat transport was vigorous at the compact yarn structure, and heat transport was affected more by fiber characteristics than yarn structure. In conclusion, sheath/core composite yarns were relevant to the high absorptive cool suit along with siro-fil and CoolMax/Bamboo staple yarns that were relevant to the heat diffusive cool suit.

• 보존과학회지
• /
• 제27권2호
• /
• pp.201-209
• /
• 2011

야외에 놓여 있는 석조 문화재는 시간관 환경에 의한 풍화에 노출되어 있다. 따라서 문화재 석재 자체의 특성을 강화시켜 풍화에 대한 저항력을 높일 수 있는 강화제가 필요하다. 풍화된 석조문화재 보존은 tetraethoxysilane (TEOS)와 같은 알콕시실란계 강화제의 솔-젤 반응을 이용하여 강화시키고 있다. 솔-젤 반응 후 얻어진 젤의 치밀한 망상구조와 건조 시 모세관 힘의 발생으로 균열이 형성되어 2차 훼손 가능성이 높은 상업용 알콕시실란계 강화제를 대체할 유연한 알킬사슬을 가진 TEOS/(3-glycidoxypropyl) trimethoxysilane (GPTMS)계 강화제에 알킬 기능기를 가진 ethyltriethoxysilane (ETEOS)를 첨가하여 강화제의 표면 소수특성을 향상시킨 강화제를 개발하였다. ETEOS의 양과 가수분해와 축합반응으로 이루어지는 솔-젤 반응 속도를 가수분해의 양을 조절하여 제어하였다. 솔-젤 반응 특성을 무게 변화, FT-IR 등으로 확인하였고, 외부에 노출되어 풍화된 경주 남산근처의 화강암에 처리하여 물 함침량, 표면접촉각, 강화 효과 등을 측정하여 응용가능성을 확인하였다.

• 한국식품영양학회지
• /
• 제10권2호
• /
• pp.234-240
• /
• 1997

식품산업을 포함한 다양한 분야에서 이용되고 있는 한천의 용도를 개발하기 위하여 각종 물리적인 처리가 한천의 열적 특성에 미치는 영향과 각 처리에 다른 표면구조의 변화를 조사하였다. 시차주사 열량분석기를 이용하여 w사한 일반한천의 흡열개시온도(To), 최대흡열점의 온도(Tp) 및 흡열완료온도(Te)는 81.20, 95.51 및 $112.14^{\circ}C$였으며, 분무건조한천은 60.11, 76.45 및 $89.54^{\circ}C$였고, 압출성형한천은 41.30, 61.72 및 $80.50^{\circ}C$로 압출성형한천이 가장 낮은 온도에서 진행되었다. 또한 엔탈피도 일반한천 3.22cal/g, 분무\ulcorner한천 1.53cal/g, 압출성형한천 0.73cal/g의 순서로 압출성형한천에서 가장 낮았다. 완전히 가열용해한 각 한천을 다시 냉각, 응고 후에 다시 승온하였을 때의 To, Tp 및 Te는 일반한천 80.70, 95.61 및 $110.92^{\circ}C$, 붐무건조한천 79.54, 93.76 및 $109.84^{\circ}C$, 압출성형한천 79.25, 93.19 및 $108.77^{\circ}C$로 한천의 종류에 따른 차이는 없었다. 엔탈피 역시 큰 차이를 보이지 않았다. 광학현미경과 주사전자현미경에 의해 표면구조를 관찰한 결과, 일반한천의 경우 단단한 구조로 균열이나 기공들이 관찰되지 않았고, 분무건조한천은 많은 미세입자들이 다량으로 느슨하게 붙어있는 다공질구조로 외부에 노출되는 표면적이 넓었으며, 압출성형한천은 굴곡, 요철 및 균열이 생겨서 수분침투가 용이한 구조를 이루고 있었다.

• Corrosion Science and Technology
• /
• 제7권2호
• /
• pp.119-124
• /
• 2008

Steel is generally not corrosion resistant to water with formation of non protective rusts on its surface. Rusts are composed of iron oxides such as $Fe_3O_4$, $\alpha-$, $\beta-$, $\gamma-$and ${\delta}-FeOOH$. However, steel, particularly weathering steel containing small amounts of Cu, Ni and Cr etc., shows good corrosion resistance against rural, industrial or marine environment. Its corrosion rate is exceedingly small as compared with that of carbon steel. According to the exposure test results undertaken in outdoor environments, the atmospheric corrosion rate for weathering steel is only 1 mm for a century. Atmospheric corrosion for steels proceeds under alternate dry and wet conditions. Dry condition is encountered on steel surface on fine or cloudy days, and wet condition is on rainy or snowy days. The reason why weathering steel shows superior atmospheric corrosion resistance is due to formation of corrosion protective rusts on its surface under very thin water layer. The protective rusts are usually composed of two layer rusts; the upper layer is ${\gamma}-FeOOH$ termed as lepidocrocite, and inner layer is nano-particle ${\alpha}-FeOOH$ termed as goethite. This paper is aimed at elucidating the atmospheric corrosion mechanism for steel in comparison with corrosion in bulky water environment by use of empirical data.The summary is as follows: 1. No corrosion protective rusts are formed on steel in bulky water. 2. Atmospheric corrosion for steel is the corrosion under wetting and drying conditions. Corrosion and passivation occur alternately on steel surface. Steel, particularly weathering steel with small amounts of alloying elements such as Cu, Ni and Cr etc. enhances forming corrosion protective rusts by passivation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.55-61
• /
• 2002

Ultra-fine particles of $SnO_{2}$ was synthersized by the sol-gel powder processing using tin(II) chloride dihydrate$(SnCl_{2}{\cdot}2H_{2}O)$ and ethanol$(C_{2}H_{5}OH)$ as raw materials. Gel powders can be obtained by drying of sol at $120^{\circ}C$ after aging 72hrs and 168hrs. The amount of $SnO_{2}$ phase was increased with temperature because of the evaporation of volatile components, and the creation of $SnO_{2}$ phase was almost done by the heat treatment at $700^{\circ}C/30min$ The grain sizes after firing are about 20-30nm, and it showed the narrow distribution of grain size. The specimens to measure electrical properties were fabricated by the thick film screen printing technique on the alumina substrates. The conductance of $SnO_{2}$ was increased with temperature up to $380^{\circ}C$ by the typical conduction mechanism of semiconducting ceramics. There was a region of constant conductance between about $200^{\circ}C$ and $380^{\circ}C$ due to the increment of electron concentration with temperature and the annihilation of conduction carriers by the absorption and electron trapped-ionization of oxygen on the surface of $SnO_{2}$, It was finally showed the intrinsic behaviors above $450^{\circ}C$. The sensing properties of response time, recovery, and sensitivity of CO were improved with aging time.

• 한국지구과학회지
• /
• 제35권7호
• /
• pp.501-517
• /
• 2014

주상절리에 관한 최근 연구를 살펴본 결과, 우리나라에 분포하는 주상절리를 이해하고, 활용하기 위한 연구 방향은 다음과 같다; 칼러네이드와 엔테블러춰의 기하학적 형태, 형성 메커니즘과 패턴의 변화, 수평단면과 내부 구조, 주상절리 상하부의 판상절리, 전분 혼합액의 건조실험, 절리 형성에 대한 수치 모델 및 컴퓨터 그래픽 활용, 화산암의 산출 상태에 따른 주상절리 형태와 크기, 모암의 암석학적 및 광물학적 연구. 이와 더불어 지표에 노출된 후의 변질, 풍화작용의 결과로 만들어진 너덜겅, 토르, 타포니 등과 같은 2차적인 경관에 대한 기재도 필요하다. 이 연구는 우리나라 주상절리와 신생대 용암류를 해석하는 중요한 역할을 할 것이다. 또한 연구 성과는 지질관광의 활성화와 지질학습장 측면에서 활용도가 높을 것이다.