• Journal of the Korea Concrete Institute
• /
• v.22 no.2
• /
• pp.149-158
• /
• 2010

Recently, numerous construction techniques for repairing and strengthening methods for above ground or air exposed concrete structure have been developed. However repairing and strengthening methods for underwater structural members under continuous loading, such as piers and steel piles need the further development. Therefore, this study develops an aqua epoxy, which can be used for repairing and strengthening of structural members located underwater. Moreover, using the epoxy material and strengthening fibers, a fiber reinforced composite sheet called Aqua Advanced FRP (AAF) for underwater usage is developed. To verify and to obtain properties of the material and the performance of AAF, several tests such as pull-off strength test, bond shear strength test, and chemical resistance test, were carried out. The results showed that the developed aqua epoxy does not easily dissolve in wet conditions and does not create any residual particle during hardening. In spite of underwater conditions, it showed the superior workability, because of the high viscosity over 30,000 cps and adhesion capacity over 2 MPa, which are nearly equivalent to those used in dry conditions. In case of the chemical resistance test, the developed aqua epoxy and composite showed the weight change of about 0.5~1.0%, which verifies the superior chemical resistance.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.103-110
• /
• 2011

This study is to comparatively analyze the characteristics of pH decrease in recycled fine aggregates for embankment and landfill produced from waste concrete by using natural process and artificial process. The result was as follows In case of recycled fine aggregates left outdoor, it was found that pH level was decreased if the thickness of embankment becomes thinner, or the materials left outdoors owing to high concentration of $CO_2$ in atmosphere caused by respirations of people. When the air was permeated, pH level was decreased more effectively. It was analyzed that this phenomenon was caused by efficient supply of $CO_2$ in the recycled fine aggregates owing to high-pressure ventilators. In case of water spraying treatment, sprayed water facilitated hydration of unhydrated cement to dissolve calcium hydroxides which neutralized $CO_2$ in the atmosphere during desiccation process and decrease pH level by a considerable margin. In case of Immersed treatment, decrease of pH was not sufficient. When facilitating the supply of $CO_2$, pH level of the recycled fine aggregates was decreased by the largest margin. It was analyzed that this phenomenon was caused by efficient supply of $CO_2$. From the above results, it was analyzed that the most effective method of reducing pH level of the recycled fine aggregates from the aspects of pH reduction performance, economic efficiency and workability was repeated wet-dry cycles of spraying water to the aggregates in the proportion of 1:0.5 by weight and then treating by forcefully blowing $CO_2$ gas into the aggregates.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.2
• /
• pp.63-67
• /
• 2009

STATEMENT OF PROBLEM. Use of custom tray and tray adhesive is clinically recommended for elastomeric impression material. However there is not clear mention of drying time of tray adhesive in achieving appropriate bonding strength of tray material and impression material. PURPOSE. This study is to investigate an appropriate drying time of tray adhesives by evaluating tensile bonding strength between two types of polyvinylsiloxane impression materials and resin tray, according to various drying time intervals of tray adhesives, and with different manufacturing company combination of impression material and tray adhesive. MATERIAL AND METHODS. Adhesives used in this study were Silfix (Dentsply Caulk, Milford, Del, USA) and VPS Tray Adhesive (3M ESPE, Seefeld, Germany) and impression materials were Aquasil Ultra (monophase regular set, Dentsply Caulk, Milford, Del, USA) and Imprint II Garant (regular body, 3M ESPE, Seefeld, Germany). They were used combinations from the same manufacture and exchanged combinations of the two. The drying time was designed to air dry, 5 minutes, 10 minutes, 15 minutes, 20 minutes, and 25 minutes. Total 240 of test specimens were prepared by auto-polymerizing tray material(Instant Tray Mix, Lang, Wheeling, Il, USA) with 10 specimens in each group. The specimens were placed in the Universal Testing machine (Instron, model 3366, Instron Corp, University avenue, Nowood, MA, USA) to perform the tensile test (cross head speed 5 mm/min). The statistically efficient drying time was evaluated through ANOVA and Scheffe test. All the tests were performed at 95% confidence level. RESULTS. The results revealed that at least 10 minutes is needed for Silfix-Aquasil, and 15 minutes for VPS Tray Adhesive-Imprint II, to attain an appropriate tensile bonding strength. VPS Tray Adhesive-Imprint II had a superior tensile bonding strength when compared to Silfix-Aquasil over 15 minutes. Silfix-Aquasil had a superior bonding strength to VPS Tray Adhesive-Aquasil, and VPS Tray Adhesive-Imprint II had a superior tensile bonding strength to Silfix-Imprint II at all drying periods. CONCLUSION. Significant increase in tensile bonding strength with Silfix-Aquasil and VPS Tray adhesive-Imprint II combination until 10 and 15 minutes respectively. Tray adhesive-impression material combination from the same company presented higher tensile bonding strength at all drying time intervals than when using tray adhesive-impression material of different manufactures.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.5
• /
• pp.53-60
• /
• 2010

The comprehensive tests on unsaturated weathered granite soils are carried out to obtain the soil-water characteristic curve that is the one of the essential requisites to study the unsaturated soil. The weathered granite soils were obtained at Palgong mountain in Daegu. The existing test results have been carried out without overburden pressures and volume changes. In this study, the volumetric pressure plate extractor is improved to consider two factors such as overburden pressure and volume change. The applied overburden pressures were 0, 25, 50, 75, 100kPa and volume changes were measured at each phase. he results of this study are summarized as follows: As the overburden pressure increases, the volumetric water content decreases at the same matric suction and the air entry value increases and gradient of curve at the transition zone and the size of the hysteresis loops decreases. As the overburden pressure increases, the degree of saturation increases at the same matric suction and degree of saturation of the wetting curve is higher than that of dry curve. The SWCC with volume changes are slightly larger than those without volume changes. The general equation proposed by Fredlund & Xing(1994) to fit the experimental result of the SWCC indicates good agreement. The empirical parameters a, n, m as overburden pressure show similar inclination as the existing results.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.2
• /
• pp.13-23
• /
• 2013

The Korean Peninsula is considered as a seasonal frozen area that is thawed in the spring and frozen in the winter. The influence of fines of the frost susceptibility of subgrade soils were established by laboratory freezing tests simulating closely the thermal conditions in the field. During the winter season, the climate is heavily influenced by the cold and dry continental high pressure. Because of siberian air mass, the temperature of January is $-6{\sim}-7^{\circ}C$ on average. This chilly weather generate the frost heaving by freezing the moisture of soil and damage potential of the geotechnical structure. In the freezing soil, the ice lenses increase the freeze portion of soil by absorbing the ground water with capillary action. However, the capillary characteristics differ from the sort of soil on the state of freezing condition. In this study, ten soil samples are prepared. The basic physical property tests were performed by following the Korean Industrial Standard and the soil specimens were classified by the Unified Soil Classification System (USCS). These classified soils are used to perform the laboratory opened systems freezing test in order to determine the frost heaving characteristics of soils such as unfrozen water content, heaving amount, and freezing depth.

• Korean Journal of Agricultural Science
• /
• v.28 no.1
• /
• pp.27-32
• /
• 2001

Two experiments were conducted to investigate the effects of the addition of ginseng meal to distillers feed on the silage quality, and feed intake and dry matter (DM) digestibility in goats. In Experiment I, three levels of ginseng meal (0.15, and 30%) were added to the distillers feed to make three types (treatment) of distillers feed silages (DFS), There were five replicates per treatment. Samples of 20 kg each were put into vinyl bag and vacuumed by an air compressor. Vinyl bags were kept at $20{\sim}25^{\circ}C$ for 30 days before being analyzed. In Experiment II, 12 male Korean native goats were employed to investigate the DM intake and digestibility of silages from Experiment I. There were 4 replicates per treatment. Daily feed intakes and fecal excretion were measured. In Experiment I, the silage pH decreased and the lactic acid increased significantly by the addition of ginseng meal (P

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3D
• /
• pp.413-420
• /
• 2011

An experiment was conducted to suggest the road pavement material combining wooden chip crushed from little useful roots and branches from logging sites or wood waste from construction sites with urethane resin. For the specimen, the mass ratio of urethane resin to construction wood waste chip/lumber waster chip was set to three different levels of 0.5, 0.75, and 1.0, which was measured, mixed with mixer, and molded; 7 days after, tensile strength test, elasticity test using golf balls and steel balls, permeability coefficient measurement, and flammability test were executed. As the result, the tensile strength of the specimen at the dry state in the air exhibited the range of 0.2-1.1MPa, and there was no change after 7 days of aging. When submerged in water, however, the strength was partially diminished; the diminishing rate was greater for less urethane resin usage, and therefore it appears desirable to set the mass ratio of resin to the wood waste chip over 0.75 to consider the moisture intrusion by precipitation and such. As the result of elasticity test, the GB and SB coefficients of the specimen using wood waste chips and urethane resin were measured to be low at below 20%, exhibiting excellent elasticity as road pavement material. Also, the permeability coefficient was over 0.5mm/sec for specimens of all combinations, exceeding the standard value required after construction for permeable pavement material, and the flammability of wood-type pavement material was evaluated to have no practical issues.

• Journal of Ginseng Research
• /
• v.31 no.4
• /
• pp.222-229
• /
• 2007

Changes on physicochemical properties of fresh Korean ginseng during repeated 9 times steaming processes, steaming $90{\sim}95^{\circ}C$ for $1{\sim}3\;hr$ followed by hot air-drying at $50^{\circ}C$ for $36{\sim}48\;hr$, were investigated. The water contents decreased from 73.4% of fresh ginseng to 13.7% finally. The final yields in bases of total weights and dry matter were 21.0% and 79.0%, respectively. As the times of steaming processes increased, lightness (L value) decreased and redness (a value) increased in color of ginseng powder. Browning index also rapidly increased after 3 times of steaming process in particular. Total water soluble sugar contents decreased from 55.4% in fresh to 38.6% in final processed ginseng, but acidic polysaccharide contents increased by about 50% with increasing times of steaming process. Total phenolic compound contents significantly increased with repeated steaming processes especially after 5 times of steaming processes and crude saponin contents also increased in some degree. In the case of major ginsenosides, the contents of $Rb_1$, $Rb_2$, $Rg_1$, Re (representative ginsenosides in fresh ginseng) decreased, but those of $Rg_2$, $Rh_1$, $Rg_3$ (unique ginsenosides in red ginseng) increased after especially 5 times of steaming processes.

• Korean Journal of Agricultural Science
• /
• v.37 no.2
• /
• pp.191-197
• /
• 2010

The objective of this research was to determine the influence of the physical and chemical properties of root substrates used during the production of 'Maehyang' strawberry propaguleson the growth of the mother plants and the rate of daughter plant formation. Plants were cultured in plastic bags containing six different formulations of root substrates composed of: a) 50% coir dust and 50% perlite (5:5 by volume, A), b) 60% coir dust and 40% perlite (6:4, B), c) 70% coir dust and 30% perlite (7:3, C), d) 70% coir dust and 30% coconut chip (7:3 D), e) 60% coir dust and 40% coconut chip (60:40, E), or f) 50% sphagnum peat and 50% vermiculite (50:50, F). All media formulations contained a moderate level of base fertilizers. Physical and chemical properties of each formulation were determined before plant establishment and after 120 days of stock plant culture and runner production. Total porosity (TP) and container capacity (CC) of all substrate formulations were higher than 85% and 55%, respectively, allowing a suitable range of air and water holding characteristics. Formulation F provided the highest TP and CC values among the all substrate modifications evaluated. Substrate formulations A, B, C and F had higher electrical conductivity (EC) and $NO_3{^-}$-N concentrations than formulations D and E, when determined before and after plant culture. Formulations A, B, C, and F, having higher EC readings, also performed better as root substrates thanthe formulations D and E in increasing fresh and dry weights of the runners as well as the production of daughter plants per plant. The 'Maehyang' strawberry plants grown in the formulation F had the highest tissue N content, followed by those grown in substrate B, A, C, or D for 120 days after transplanting. Formulation F also facilitated accumulation of higher tissue phosphorus (P) and copper (Cu) contents compared to other treatments. Results of this experiment suggest that the chemical properties, rather than physical properties, of root substrates had a major influence on the growth of mother plants and the occurrence of healthy daughter plants during the bag-culture phase of propagation.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.4
• /
• pp.339-347
• /
• 2012

In previous studies, methods for enhancing cellular response on the Hydroxyapatite coated implant surface were described. In this study, the changes of surface characteristics such as surface roughness, contact angle, surface energy and surface morphology were observed when Hydroxyapatite coated Ti discs were immersed in NaCl solution for various time. Hydroxyapatite coated Ti discs were immersed in 0.9% NaCl solution for 7, 14 and 21 days at $37^{\circ}C$. The control group comprises dry identical discs not immersed in a solution. (n=3) All discs were dried in air completely and the surface roughness was measured using confocal laser scanning microscopy(CLSM). Static contact angle was recorded by video contact angle analyzer after dropping distilled water on the surface. The surface energy was calculated from contact angles of the three liquids. Surface was observed using a field emission-scanning electron microscope(FE-SEM). As a result, the surface roughness of immersed Hydroxyapatite coated Ti discs increased significantly and the contact angle decreased comparing with control group discs. The surface energy of immersed discs increased except for discs immersed for 14 days.