• Journal of the Korea Institute of Building Construction
• /
• v.4 no.4
• /
• pp.71-77
• /
• 2004

Drying Shrinkage has much complexity as it has relations with both internal elements of concrete and external factors. Therefore, experiments on Concrete Drying Shrinkage are carried out in this study under simplified circumstances applying temperature & Humidity test chamber which enables constant temperature and humidity. Comparative analyses have been made respectively according to the consequences aiming at modelling for prediction of Concrete Drying Shrinkage and making out measures to reduce it. Strain Rate of Drying Shrinkage of concrete under the condition of dry air appears to rise by about 20%-30% in proportion as the temperature rises $5^{\circ}C$ when the humidity was held below 10% compared under the condition of dry temperature & Humidity test chamber. Strain Rate of Drying Shrinkage in pit sand concrete increased 20% higher than measured when in river sand under the condition of 90-day material age. A general formula with two variables is derived as follow ${\varepsilon}={\alpha}_1＋{\beta}_1x_1＋{\beta}_2x_2＋{\beta}_3x_1^2＋{\beta}_5x_2^2$. and also graphed in 3 dimensions, enabling to apply to actual design and predict Strain Rate of Drying Shrinkage in concrete. The results of prediction of Rate of Drying Shrinkage by Response Surface Analysis are as follows. The coefficient of correlation of Drying Shrinkage in Concrete was over 90%.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.3
• /
• pp.116-122
• /
• 1999

The purpose of this study is to develop new process named "hydrogen peroxide dissolution method". This process used hydrogen peroxide, which is harmless to human body and oxidize molybdenum wire selectively.The advantages of hydrogen peroxide dissolution method were no discharge of noxious matter when dissolution of molybdenum wire which used as the center supporter, reactions occur in room temperature and easy to recover dissolved molybdenum. This study was aimed at gathering the basic data of molybdenum wire dissolution-recovery process and proposes the reaction condition of molybdenum wire dissolution-recovery process and the factors influencing those reactions. The results were as follows:1. In the dissolution of molybdenum wire, the early condition of reaction was $15^{\circ}C$, and the temperature condition of state was $32^{\circ}C$. 2. 1) In the GSL-60W type, P.W.(Piece weight) was 11.89mg, C.R. was $65.6\Omega$. 2) In the FL-20W type, P.W. was 11.60mg, C.R. was $4.6\Omega$. 3. The molybdenum of process water was treated of a precipitation after dry and after stagnation in the one day, the molybdenum of upper water was treated of precipitation after dry and after congelation.

• Textile Coloration and Finishing
• /
• v.32 no.2
• /
• pp.89-95
• /
• 2020

In this study, the efficacy of Amaranth(Amaranthus spp. L.) as a natural dye resource was investigated for wool fabrics. It is known that a large amount of flavonoid and anthocyanin colorant are contained in leaves and stems, as well as red flowers. The optimum condition of dyeing was 1.3% of dye concentration(o.w.b.) at 100℃ for 60 minutes, resulting the K/S value, 23.43 and R Munsell color on the wool fabrics. Al, Fe, Zinc and Titanium were used as a mordant. The mordant improved the dye uptake, regardless of the mordant type and mordant method. The pre-mordanting method was more effective than the post-mordanting method. Al pre-mordanted fabric showed the highest K/S, 30.02. Light fastness and washing fastness were high in grades 4-5 and 5, and rubbing fastness was good in grades 4 and 4-5 in dry condition, but low in grades 2-3 and 3 in wet condition. The dry cleaning fastness was excellent in all 5 grades. However, the alkaline perspiration fastness ratings were low in grades 2-3 and 3. The results show Amaranthus spp. L. colorant can be used as a functional natural dye for wool fabrics.

• Journal of Korea Foundry Society
• /
• v.10 no.3
• /
• pp.235-246
• /
• 1990

This study has been carried out to investigate into the rolling wear characteristics of austempered ductile iron under unlubricated dry rolling condition by Amsler type test with 9.09% sliding ratio. Wear amount is increased with increasing of ferrite and retained austenite and it has been found that the amount of rolling wear is decreased when the hardness of matrix are higher. The rolling life up to generation of abnormal condition is conspicusly increased and amount of rolling wear is increased asrolling revolutionis increased and wear of austempered ductile ironunder dry rolling condition. Matrix has been obtained to upper bainite, low bainite at heat treatment, obtained to bull`s eye structure at as cast. It has been found that the amount of rolling wear is decreased when the tensile strength of the casting are increased and then the rolling life up to generation of abnormal wear in conspicuously increased and amount of wear was intend to graphite content.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.29 no.4
• /
• pp.362-365
• /
• 1984

Application of phosphate and silicate at the seed bed stage of rice seedlings was investigated to improve nutritional condition and rooting capability at low temperature. The amounts of applied phosphate were 15kg/10a with or without 200 kg/10a of silicate, and 30 kg/10a without silicate. Seeding dates were March 31, April 9 and April 19. The dry weight of the seedlings seeded earlier date under low temperature was lower than that of the seedlings seeded later dates. The application of phosphate and silicate increased the dry weight of newly developed roots after trasplanting, and increased the number of tillers. Therefore, heavy application of phosphate and silicate is recommendable to improve the predisposition of the rice seedlings grown under the low temperature condition for early transplanting.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.293-296
• /
• 1998

Surface electrical conduction in insulator is most important factor to assess the insulation performances of outdoor insulating materials. In this paper, contamination performance of the widely used materials for outdoor insulator - porcelain, EPDM, Silicone rubber - were discussed by measuring properties of average leakage current and scintillation discharge pulses under artificial contamination conditions. The artificial contaminations used were deionized distilled water fog, 0.5wt% NaCl salt fog of light pollution and 2wt% NaCl salt fog of medium pollution. The average leakage current was appeared linearly with applied voltage at dry and clean surface condition. The magnitude of leakage current was almost same at different kinds of samples. In case of deionized distilled water fog, the characteristics of leakage current and applied voltage was most different to that in case of dry and clean condition. In case of salt fog pollution condition, The leakage current was increased above critical voltage. The scintillation discharges were also activated at the level. the leakage current and scintillation discharges were increased with increasing pollution degree. The resistance to pollution properties of silicone rubber appeared excellent among them.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.207-210
• /
• 1998

Surface electrical conduction in insulator is most important factor to assess the insulation performances of outdoor insulating materials. In this paper, contamination performance of the widely used materials for outdoor insulator - porcelain, EPDM, Silicone rubber - were discussed by measuring properties of average leakage current and scintillation discharge pulses under artificial contamination conditions. The artificial contaminations used were deionized distilled water fog, 0.5wt% NaCl salt fog of light pollution and 2wt% NaCl salt fog of medium pollution. The average leakage current was appeared linearly with applied voltage at dry and clean surface condition. The magnitude of leakage current was almost same at different kinds of samples. In case of deionized distilled water fog, the characteristics of leakage current and applied voltage was most different to that in case of dry and clean condition. In case of salt fog pollution condition. The leakage current was increased above critical voltage. The scintillation discharges were also activated at the level the leakage current and scintillation discharges were increased with increasing pollution degree. The resistance to pollution properties of silicone rubber appeared excellent among them.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.758-762
• /
• 1998

Electrical conduction property of insulator surface is most important factor to assess the insulation performances of outdoor insulating materials. In this paper, contamination performance of the materials to be used for outdoor insulator such as porcelain, EPDM, silicone rubber was discussed by measuring properties of average leakage current and scintillation discharge pulses under salt fog conditions. The fog was applied by nozzle in chamber and fogging fluids were deionized distilled water, 0.5wt% NaCI solution and 2wt% NaCl solution. The average leakage current showed linearly with applied voltage at dry and clean surface condition. The magnitude of leakage current was almost same at different kinds of samples. In case of deionized distilled water fog, the characteristics of leakage current and applied voltage were much different to those in case of dry and clean condition with 2wt% salt fog. In case of slat fog pollution condition, the leakage current was increased above critical voltage. the scintillation discharges were also activated at the level. The leakage current and scintillation discharges were increased with increasing pollution degree. The resistance to pollution properties of silicone rubber appeared excellent among them.

• Journal of Korea Foresty Energy
• /
• v.21 no.3
• /
• pp.10-17
• /
• 2002

This study was carried out to investigate a heat treatment condition and suitable drying schedule of bamboo material(Phyllostachys nigra var. henonis) for a vertical flute with small-notched bamboo. It is very important to prevent drying defects during its drying process. We investigated the effort of heat treatment the most suitable drying schedule for small-notched bamboo vertical flute without drying defects in this research. A direct heat treatment method and drying conditions of 3($20^{\circ}C$ 65%, $40^{\circ}C$ 40%, and dry at air condition) were applied to the Bamboo specimen that felled in several areas for a month. The result suggested that the most suitable drying schedule with the less split and the shortest time was to dry at $40^{\circ}C$, 40% condition and it was useful to direct heat-treatment because of reducing the number and size of split during drying bamboo.

• Tribology and Lubricants
• /
• v.34 no.6
• /
• pp.262-269
• /
• 2018

In this work the friction and wear characteristics of the gray cast iron surface processed by broaching method, which is widely used in the machinery industry, were investigated. The broaching process is mainly used for mass production because it has high dimensional accuracy and processing speed, but the defects on surface can be easily generated. In order to improve the tribological characteristics, the approach was to reduce the roughness and hardness of the surface by adding a machining process to the broaching specimen. The secondary machining process using abrasive grains produces low roughness and hardness than broaching because it has high tool accuracy and removes the work hardened surface. The friction coefficient and the wear rate were assessed using a reciprocating-type tribotester to analyze the effects of surface finishing on the tribological properties. The friction tests were conducted under dry and lubricated conditions. The test results showed that the reduction of surface roughness and hardness through secondary machining process in lubricated condition improved the friction and wear characteristics. The reason why the same results did not appear in a dry condition was that wear occurred more rapidly than in lubricated condition. Thus, the positive effect of roughness and hardness of the surface obtained through the secondary machining process was not observed.