• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1080-1086
• /
• 2005

We have studied the Ge redistribution after dry oxidation and the oxide growth rate of $Si_{1-x}Ge_x$ epitaxial layer. Oxidation were performed at 700, 800, 900, and $1,000\;^{\circ}C$. After the oxidation, the results of RBS (Rutherford Back Scattering) & AES(Auger Electron Spectroscopy) showed that Ge was completely rejected out of the oxide and pile up at $Si_{1-x}Ge_x$ interface. It is shown that the presence of Ge at the $Si_{1-x}Ge_x$ interface changes the dry oxidation rate. The dry oxidation rate was equal to that of pure Si regardless of Ge mole fraction at 700 and 800$^{\circ}C$, while it was decreased at both 900 and $1,000^{\circ}C$ as the Ge mole fraction was increased. The dry of idation rates were reduced for heavy Ge concentration, and large oxiidation time. In the parabolic growth region of $Si_{1-x}Ge_x$ oxidation, the parabolic rate constant are decreased due to the presence of Ge-rich layer. After the longer oxidation at the $1,000^{\circ}C$, AES showed that Ge peak distribution at the $Si_{1-x}Ge_x$ interface reduced by interdiffusion of silicon and germanium.

• KSBB Journal
• /
• v.5 no.3
• /
• pp.235-240
• /
• 1990

A quantitative physiological approach has been employed to estimate the metabolic parameters such as specific uptake rates of nutrients and specific production rate in continuous culture of Pseudomonas elodea for gellan gum production. The estimated values of metabolic parameters are used for process improvement. During the exponential growth phase, the specific growth rate was 0.16hr-1 in batch culture. The gellan gum concentration increased up to 0.7g dry weight/100g broth and the apparent viscosity of the culture broth was about 4,500 cp.(72hrs culture). The ratio of specific uptake rate of carbon to that of nitrogen were found to be optimum at about 3.0mg-carbon/mg-nitro-gen. With the improved medium, the maximum gellan production rate, 0.6g dry weight/1/hr, was obtained at D=0.14 hr-1. The shear stresses of culture broth were fairly well correlated with shear rates by using Casson equation and at highly viscous culture broth, oxygen transfer coefficient was greatly reduced.

• Microbiology and Biotechnology Letters
• /
• v.25 no.3
• /
• pp.235-239
• /
• 1997

Chlorococcum littorale has been grown in high $CO_2$ concentrations to utilize $CO_2$ gas in the polluted air. The effect of incident light intensity on the specific growth rate is expressed by a photoinhibition model, showing half- saturation constant, $K_0\;as\;8\;(W/m^2)$ and inhibition constant, Ki as 35 $(W/m^2)$. The maximum specific growth rate was also estimated as 0.095 (1/day) under this condition. This strain maintained the optimum growth rate in 20% of $CO_2$ gas but 50% of input $CO_2$ gas is the maximum concentration considering the economical efficiency. The maximum Specific $CO_2$ consumption rate, $qCO_2$ was measured as 17.48 (mg $CO_2/g$ dry wt./day) in batch cultivation, 11.2 (mg $CO_2/g$ dry wt./day) in fed-batch cultivation and 10.87 (mg $CO_2/g$ dry wt./day) at 0.065 (1/day) of dilution rate in continuous cultivation. The chemical composition of the biomass obtained from this process showed 32.5% of protein, 27.5% of lipid, 16.5% of carbohydrate and ash 11.7%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.868-871
• /
• 2003

In recent years, silicon carbide has emerged as an important material for MEMS application. In order to fabricate an SiC film based MEMS structure by using chemical etching method, high operating temperature is required due to high chemical stability. Therefore, dry etching using plasma is the best solution. SiC film was deposited by thermal CVD at the temperature of $1000^{\circ}C$ and pressure of 10 torr. SiC was dry etched with a reactive ion etching (RIE) system, using $SF_6/O_2$ and $CF_4/O_2$ gas mixture. Etch rate have been investigated as a function of oxygen concentration in the gas mixture, RF power, and working pressure. Etch rate was measured by surface profiler and FE-SEM. $SF_6/O_2$ gas mixture has been shown high etch rate than $CF_4/O_2$ gas mixture. Maximum etch rate appeared at 450W of RF power. $O_2$ dilute mixtures resulted in an increasing of etch rate up to 40%, and the superior anisotropic cross section was observed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.45 no.2
• /
• pp.128-133
• /
• 2000

This study was carried out to investigate the effect of forms and levels of nitrogen fertilizer on plant growth and essential oil production of Agastache rugosa. Calcium nitrate had more influenced on length and width of leaves and lateral branch length than did urea. When nitrogen fertilizer level was increased from 12 kgN/I0a to 24kgN/I0a, plant growth was stimulated and dry matter of leaf and inflorescence were increased. Top dry matter of plant with calcium nitrate treatment (38.4 g) was heavier than that of urea treatment (32.8 g). Interactions among accession and nitrogen form and nitrogen rate were not significantly different for top dry matter. The forms and rate of nitrogen fertilizer did not affect estragole content. The estragole contents was higher in leaf (91.8%) than that of inflorescence (81.3%). While the essential oil content was not affected by different nitrogen forms, nitrogen level affected the essential oil contents positively by increasing dry matter. Essential oil yield was not affected by accession or nitrogen form, but by nitrogen rate. With increasing N application from 12kgN/I0a to 24 kgN/I0a, essential oil yield was increased by 95.8 %.

• Journal of Biosystems Engineering
• /
• v.23 no.4
• /
• pp.335-342
• /
• 1998

The objectives of this study were to evaluate respiration characteristics and develop empirical respiratory rate equations for short gain rough rice. The carbon dioxide concentrations generated from mush rice at four level temperatures(10, 20, 30, 4$0^{\circ}C$) and 4 level moisture contents(17.2, 21.5, 25.9, 31.6％, d.b.) were measured by gas chromatography. The respiratory rates' increased exponentially with gain temperature and also with moisture content The relationship between respiratory rate and gain temperature fitted the Arrehenius' and Core's equations very well. Two empirical respiratory rate equations were presented as a function of gain temperature and moisture content. The values of determination coefficient for the developed respiratory rate equations were 0.999, and the result of t-test showed that there were no significant differences between predicted and measured respiratory rates on significance level of 1%. Therefore, it appeared that respiratory rates predicted by the respiratory rate equations agreed well with measured values. An equation for predicting dry matter losses of rough rice during storage was presented by modifying the respiratory rate equations based on chemical reaction of decomposition of carbohydrate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.128-128
• /
• 2010

In this study, we investigated the evolution and reduction of the surface roughness during the high-speed chemical dry thinning process of Si wafers. The direct injection of NO gas into the reactor during the supply of F radicals from NF3 remote plasmas was very effective in increasing the Si thinning rate, due to the NO-induced enhancement of the surface reaction, but resulted in the significant roughening of the thinned Si surface. However, the direct addition of Ar and N2 gas, together with NO gas, decreased the root mean square (RMS) surface roughness of the thinned Si wafer significantly. The process regime for the increasing of the thinning rate and concomitant reduction of the surface roughness was extended at higher Ar gas flow rates. In this way, Si wafer thinning rate as high as $20\;{\mu}m/min$ and very smooth surface roughness was obtained and the mechanical damage of silicon wafer was effectively removed. We also measured die fracture strength of thinned Si wafer in order to understand the effect of chemical dry thinning on removal of mechanical damage generated during mechanical grinding. The die fracture strength of the thinned Si wafers was measured using 3-point bending test and compared. The results indicated that chemical dry thinning with reduced surface roughness and removal of mechanical damage increased the die fracture strength of the thinned Si wafer.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.5
• /
• pp.751-757
• /
• 2011

The monitoring technique based on electrical conductivity (EC) can provide researchers with some advantages in maintenance management and is cost-effective as compared with existing CSOs monitoring. In this study, the flow rate estimation using EC data was executed in two sites where storm overflow chamber had installed. In the result of A-site, R2 of second order multinomial between dilution ratio of EC and observed flow rate was showed the range of 0.68 ~ 0.77. And $R^{2}$ of B-site was 0.62 ~ 0.81. On the other hand, cumulative frequency of A-site was 43.4 ~ 52.2% in the relative error level of under 20%. And B-site was 10.1 ~ 46.5%. The flow rate estimation formula was improved through consideration of some parameters including antecedent dry days and rainfall duration. And difference between estimated flow rate and observed flow rate in total rainfall event was very small.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.3
• /
• pp.169-175
• /
• 2022

This study aimed to examine the changes in dry matter yield and growth characteristics of alfalfa (Medicago sativa L.) in response to variations in sowing dates during the autumn season of 2021-22 in a dry paddy field of Chilbo-myeon, Jeongeup-si, Jeollabuk-do. Treatments comprised four sowing dates at 10-day intervals, i.e., October 8, October 18, October 28, and November 8, 2021. The winter survival rate of alfalfa showed a significant difference between different treatments but was at a satisfactory level for all (p<0.05). The winter survival rate for the fourth sowing date, a month later than the first sowing date, was approximately 11.7% lower than that for the first sowing date. The plant height ranged between 82.3-93.1 cm and 60.5-63.7 cm at the first and second harvest, respectively, smaller at the second harvest than at the first harvest. The total dry matter yield of alfalfa was the highest at 13,316 kg/ha for the first sowing date, and the later the sowing date, the lower the dry matter yield. The protein content of alfalfa ranged between 13.6-17.3% in the first harvest, lower than the standard alfalfa protein content of 20% or more. In relative feed value, the first sowing (Oct. 8) was the most significantly higher in the first harvest (p<0.05). These results suggest that the early and mid-October sowing dates are optimum for sowing alfalfa during autumn and result in improved plant growth, dry matter yield, protein content, and winter survival compared to those at later sowing dates. Therefore, dry paddy fields can be safely employed for alfalfa cultivation with sowing dates in early and mid-October during autumn.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.12
• /
• pp.1922-1929
• /
• 2020

Objective: The present study aimed to survey seasonal changes in reproductive performance of local cows receiving artificial insemination (AI) in the Pursat province of Cambodia, a tropical country, to investigate if ambient conditions affect the reproductive performance of cows as to better understand the major problems regarding cattle production. Methods: The number of cows receiving AI, resultant number of calving, and calving rate were analyzed for those receiving the first AI from 2016 to 2017. The year was divided into three seasons: cool/dry (from November to February), hot/dry (from March to June), and wet (from July to October), based on the maximal temperature and rainfall in Pursat, to analyze the relationship between ambient conditions and the reproductive performance of cows. Body condition scores (BCS) and feeding schemes were also analyzed in these seasons. Results: The number of cows receiving AI was significantly higher in the cool/dry season than the wet season. The number of calving and calving rate were significantly higher in cows receiving AI in the cool/dry season compared with the hot/dry and wet seasons. The cows showed higher BCSs in the cool/dry season compared to the hot/dry and wet seasons probably due to the seasonal changes in the feeding schemes: these cows grazed on wild grasses in the cool/dry season but fed with a limited amount of grasses and straw in the hot/dry and wet seasons. Conclusion: The present study suggests that the low number of cows receiving AI, low number of calving, and low calving rate could be mainly due to poor body condition as a result of the poor feeding schemes during the hot/dry and wet seasons. The improvement of body condition by the refinement of feeding schemes may contribute to an increase in the reproductive performance in cows during the hot/dry and wet seasons in Cambodia.