• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.441-444
• /
• 2006

Extrusion molding concrete panel is cured two times, that is the steam curing at atmospheric pressure and a high-pressure steam curing(autoclaving). Steam curing at atmospheric pressure is done before autoclaving and to acquire the proper strength for treat in process. Though this curing is the important factor on the quality of product and the speed in manufacturing process, it was not evaluated properly so far. Because of ignorance about curing, some engineers even think that the dry curing is better than the steam curing. This study is to investigate the properties of specimen according to variation of curing conditions in the coring chamber such as laboratory scale, pilot plant, and commercial plant. As estimating, in case of steam curing at atmospheric pressure to make extrusion molding concrete panel, moisture curing is better than dry curing and the desirable maximum temperature in curing chamber is about $50^{\circ}C$.

• Journal of the Korean Society of Safety
• /
• v.12 no.2
• /
• pp.102-111
• /
• 1997

An In-line dry scrubbing FGD process was investigated. Calcium hydroxide was entrained in flue gas and the SO$_2$ removal efficiency by humidity and additives were examined. The range of reaction temperature was $200^{\circ}C$~$500^{\circ}C$ and the concentration of $SO_2$ was around 900ppm. By the increase of humidity in flue gas, the removal efficiency was increased. The effect of NaOH as a additive was very high and got high conversion of $Ca(OH)_2$, however in case of RH 90%, it was reverse. The effect of particle size and flow rate were examined. And the reaction rate constant and effective diffusivity also calculated.

• Tribology and Lubricants
• /
• v.25 no.1
• /
• pp.66-72
• /
• 2009

Al-based composites reinforced with SiC particulate were fabricated using a thermal spray process, and dry sliding wear behavior of the composites was investigated. Pre-mixed Al and SiC powders were sprayed on an A16061 substrate by flame spraying, and dry sliding wear test were performed under various sliding speed and applied load conditions against ${Al_2}{O_3}$ ball. Wear behavior of the composites was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). And build-up mechanism of MML on the worn surface of the composites was examined. It was revealed that these MML was formed of debris from the contact surface of the composites and effected to wear behavior of the composites protecting the contact surface of the composites.

• KSBB Journal
• /
• v.24 no.4
• /
• pp.377-382
• /
• 2009

The culture condition of growing Chlorella minutissima was optimized to produce biodiesel for fed-batch cultivation. First, under heterotrophic cultivation, the optimum level of glucose was determined to be 10 g/L for 20 days. After, three cultivation conditions were operated: autotrophic, heterotrophic, and mixotrophic growth. The lipid level and the maximum cell concentration from the fed-batch heterotrophic process were 32.0 (%, v/v) and 15.0 (g-dry wt./L) in 20 L flask, respectively. In addition, since the relatively constant specific lipid production rate was observed as 0.040 (% lipid/g-dry wt./day) at the latter period of cultivation time, the fed-batch process could maintain continuous lipid production. Fed-batch process is higher than those values from the batch process. The lipids from the fed-batch process contained over 38% of $C_{18}$, known as the suitable composition for the biodiesel application. For mixotrophic and heterotrophic growth under fed-batch condition, glucose was proved to be an appropriate carbon source for a large scale outdoor cultivation. For fed-batch cultivation, the feeding rate of seawater medium containing glucose was decided to be 0.5 L/day. The mixotrophic cultivation maintained maximum cell concentration of 24 (g-dry wt./L) and the lipid level of 43 (%, w/w). The lipid composition from this process was also proved to be suitable for the biodiesel production. The fatty acids from the mixotrophic growth contains 18% of $C_{17}$ and 49% of $C_{18}$, implying It also tells that C. minutissima is a suitable resource of biodiesel. Especially, the mixotrophic cultivation with fed-batch process might be useful for the large scale cultivation for the biodiesel production.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.4
• /
• pp.443-451
• /
• 2010

This study was conducted to confirm the CSOs characteristics, and to estimate treatment efficiency of CSO treatment process. Flowrate was average $53,500m^3$/d, maximum $58,100m^3$/d during dry season, but after rain-fall, the flowrate was increased more than twice that of the dry season. And, water pollution concentrations, such as $COD_{Cr}$, SS, $BOD_5$, TN and TP of after rain-fall, were also increased. Thus, for more efficient treatment of pollutants during rainy season, The vortex separator and continuous fiber filter devices were used. From the results on particle range, removal efficiency of particle was 99.7% at the particle size range of $40{\sim}100{\mu}m$ but decreased as 55-80% at the below $40{\mu}m$. The removal efficiencies of $COD_{Cr}$, SS, TN and TP were approx. 70, 60, 70 and 50, respectively during the dry season and approx. 50, 50, 8 and 18% during the rainy season. Also, when compared with the primary sediment basin, $COD_{Cr}$, SS, TN and TP removal efficiencies were high. especially, at the case of TN and TP, TN was more removed than TP because of higher conversion factor value. But we needed more study for the injection of a coagulants to get more stable treatment efficiency for soluble pollutants. Consequently, This process can be used for CSOs treatment as well as replace the primary sedimentation basin during the dry season.

• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.635-639
• /
• 2003

We investigated dry etching of GaAs and AiGaAs in a high density planar inductively coupled plasma system with BCl$_3$and BCl$_3$/Ar gas chemistry. A detailed etch process study of GaAs and ALGaAs was peformed as functions of ICP source power, RIE chuck power and mixing ratio of $BCl_3$ and Ar. Chamber process pressure was fixed at 7.5 mTorr in this study. The ICP source power and RIE chuck power were varied from 0 to 500 W and from 0 to 150 W, respectively. GaAs etch rate increased with the increase of ICP source power and RIE chuck power. It was also found that etch rates of GaAs in $15BCi_3$/5Ar plasmas were relatively high with applied RIE chuck power compared to pure 20 sccm $BCl_3$plasmas. The result was the same as AlGaAs. We expect that high ion-assisted effect in $BCl_3$/Ar plasma increased etch rates of both materials. The GaAs and AlGaAs features etched at 20 sccm $BCl_3$and $15BCl_3$/5Ar with 300 W ICP source power, 100 W RIE chuck power and 7.5 mTorr showed very smooth surfaces(RMS roughness < 2 nm) and excellent sidewall. XPS study on the surfaces of processed GaAs also proved extremely clean surfaces of the materials after dry etching.

• Journal of environmental and Sanitary engineering
• /
• v.23 no.3
• /
• pp.9-22
• /
• 2008

This study was conducted to develop a system that processes harmful gases and dust, which being generated in the production of micro-inorganic fabric. This can be obtained by melt spinning raw materials such as agalmatolite, fluorspar, limestone, silica under high temperature at $1500-1600^{\circ}C$ in a glass recuperator using a dry method by Cyclone Reactor or Envelope Type (ET) type Bag Filter. If the number of the members of Korea Glass Industry Association reaches up to 45, the damage of the harmful gas being generated in recuperator should not be small. In addition, research of existing facilities showed the most of harmful gas treatment facilities which adopt wet treatment or semi-dry treatment process. This was caused the problems for wastewater and the second pollutive materials. Moreover, in the dust collecting facility behind recuperator, it is also problematic that electric dust collector requires enormous initial investment. We have researched various methods to show both economic and efficient new processes for the preventive facilities of recuperator. As the result of the experiments, the removal efficiencies of HF and SOx were 99% and 87%, respectively. Although it was insignificant reaction, a pretty much interesting result that NOx showed an absorption reaction with $Ca(OH)_2$(removal efficiency was more than 25%) was obtained.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.1
• /
• pp.15-22
• /
• 2002

We received 2 types flexible packaging films from two companies that laminated PET $16{\mu}m/dry$ lamination/aluminium foil $7{\mu}m/dry$ lamination/CPP $80{\mu}m$ films. For the reason of hot sealing's trouble through filling process, We separated each layer and compared thicks, film types and tested IR, DSC and sensory test. At the result, one sample's thick is different but film types is same between samples. Optimum hot-sealing conditions between two samples is $195^{\circ}C\;and\;210^{\circ}C$. The difference is $15^{\circ}C$. According to test of direct filling packaging process by four face fluid filling machine, two sample's sealing strength of hot-sealing is $4.76kg/cm2/15mm$(sample of optimum hot-sealing condition is $195^{\circ}C$) and $3.84kg/cm2/15mm(210^{\circ}C)$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.4
• /
• pp.560-565
• /
• 2020

Korea's seaweed is using a method that is not suitable for the automated process and quality are significantly lower than the export volume of 20,000 tons or more. Therefore, in this paper, we improved the existing dry steaming weight control device and electronicized the remote control system and the existing dry steaming weight control device. This is implemented with precise and detailed device, unlike the dry seaweed weight control method using the conventional valve which depends on the user's feeling and experience. Also, because it is a remote control system, it can help to produce seaweed safely even if you don't climb on the machine. The Seaweed weight control device implemented is expected to contribute greatly to the automation process and industrial growth of the steeply growing dry laver production and export industry.

• Journal of Powder Materials
• /
• v.28 no.6
• /
• pp.462-469
• /
• 2021

Tin/graphite composites are prepared as anode materials for Li-ion batteries using a dry ball-milling process. The main experimental variables in this work are the ball milling time (0-8 h) and composition ratio (tin:graphite=5:95, 15:85, and 30:70 w/w) of graphite and tin powder. For comparison, a tin/graphite composite is prepared using wet ball milling. The morphology and structure of the different tin/graphite composites are investigated using X-ray diffraction, Raman spectroscopy, energy-dispersive X-ray spectroscopy, and scanning and transmission electron microscopy. The electrochemical properties of the samples are also examined. The optimal dry ball milling time for the uniform mixing of graphite and tin is 6 h in a graphite-30wt.%Sn sample. The electrode prepared from the composite that is dry-ball-milled for 6 h exhibits the best cycle performance (discharge capacity after 50^th cycle: 308 mAh/g and capacity retention: 46%). The discharge capacity after the 50^th cycle is approximately 112 mAh/g, higher than that when the electrode is composed of only graphite (196 mAh/g after 50^th cycle). This result indicates that it is possible to manufacture a tin/graphite composite anode material that can effectively buffer the volume change that occurs during cycling, even using a simple dry ball-milling process.