• 한국해양공학회지
• /
• 제11권2호
• /
• pp.48-56
• /
• 1997

This work has been investigated in order to study the influence of the moisture absorption on the mechanical pf the glass fiber/epoxy resein composites and the carbon fiber/epoxy resein composites. The types of glass fiber used in the glass fiber/epoxy resein composites were randomly oriented fiber and plain fabric fiber. And carbon fiber.epoxy resein composites was laminated with fabric prepreg which was formed with carbon fiber and epoxy resein. Both composites were immersed up to 100 days in distilled water at $80^{\circ}C$, and then dried up to 3 days in an oven at 80$80^{\circ}C$. Both composites were measured for the weight gain of water(wt.%) and tensile strength through immersion and dry time. Consequently, it was found that the tensile strength of thw glass fiber/epoxy resein composites and the carbon fiber/epoxy resein composites were reduced proportionally to the moisture absortion rate. Also, the tensile strength of glass fiber composites was decreased more than that of the carbon fiber composites. Additionally, it was found that the tensile strength of all composites which decreased by moisture absorption were partly recovered by drying in an oven at 80$80^{\circ}C$.

• Computers and Concrete
• /
• 제19권1호
• /
• pp.69-78
• /
• 2017

This study aimed at exploring the effect of presoaking degree of lightweight aggregate (LWA) on the fresh and hardened properties of concrete. Two series (i.e., Series A and Series B) of concrete mixes that were made of LWA with different moisture states were prepared. The presoaking degree of LWA was divided into three types: oven dry state, 1 hour prewetted and 24 hours prewetted. For the Series A, the water content of the lightweight aggregate concrete (LWAC) mixes was adjusted in accordance with the moisture condition of the LWA. Whereas the amount of water added in the Series B mixes was deliberately not adjusted for the moisture condition of the LWA. Slump test, mechanical tests, interfacial transition zone microscopical tests and thermal conductivity test were carried out on the specimens of different concretes and compared with control normal-weight aggregate concretes. The test results showed that the effect of mixing water absorption by LWA with different moisture states was reflected in the fresh concrete as the loss of mixture workability, while in the hardened concrete as the increase of its strength. With the use of oven-dried LWA, the effect of reduction of water-cement ratio was more significant, and thus the microstructure of the ITZ was more compact.

• 한국가구학회지
• /
• 제27권1호
• /
• pp.43-48
• /
• 2016

PEG (Polyethylene glycol) impregnation in wood reduces the occurrence of checking during kiln drying. The volumetric shrinkages of wood PEG impregnated by pressure (PEG-P) or soaking (PEG-S) methods, and oven-dried by vent (VD) or air-tight (AD) methods were measured and compared with the controls. The average oven-dry weight of PEG impregnated specimens was larger than that of the controls by 3.6 g, but was not influenced by the drying methods. The average of the total volumetric shrinkage of PEG-P-VD specimens was the least (2.3%), while that of CON-S-AD specimens was the largest (28.9%). Within a drying method the total volumetric shrinkage of the control was the largest followed by PEG-S and PEG-P specimens, which implied that residual PEG in wood restrained its shrinkage during drying.

• 대한치과보철학회지
• /
• 제34권4호
• /
• pp.833-849
• /
• 1996

The material of choice for functional and esthetic reconstruction of maxillofacial defects is silicone. Silicone has appropriate physical properties for maxillofacial prosthesis but it has weak edge strength. Therefore, a proper combination of silicone and polyurethane sheet is recommended to improve this weakness. Various primers are also used to enhance the adhesive strength between silicone and polyurethane sheet. The purpose of this study was to determine the adhesive strength of silicone and polyurethane sheet. Silicone elastomer mixture was made by admixing MDX4-4210 elastomer (40%) and Silastic Medical Adhesive Type A(60%). This silicone elastomer mixture was attached to polyurethane sheet, using one of three different primers(1205, S-2260, or A-304), treated for 1, 2, 4, 6, and 8 hours. These were then polymerized in room temperature, dry-heat oven or microwave oven. Six specimens per each group, a total of 270 specimens were prepared for final test. The differences of T-peel bonding strengths were then determined by a test. The differences of T-peel bonding strengths were then determined by a test method that was recommended by American Society for Testing and Materials C794-80. The results were statistically analyzed using the ANOVA and Mutiple Range Tests(Tukey' HSD). The reults were as follow. 1. Type of primer, primer reaction time, and methods of polymerization showed significant correlation on the T-peel bonding strengths in adhesiveness between silicone and polyurethane sheet. 2. A-304 primer showed statistically higher in T-peel bonding strength than otehr type of primers except for the polymerization in microwave oven with reaction times of 2, 6 hours(p<0.05). 3. No significant differences in T-peel bonding strength were observed among the polymerization methods. 4. The effect of reaction time by the primer type and polymerization method showed statistically significant differences in bonding strength among different reaction times. And in most cases, reaction time of 1 or 2 hours showed higher T-peel bonding strength.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.249-257
• /
• 2004

Drying and curing characteristics of PCM resins using the induction heater and short-wave infrared emitter module was studied to develop a compact oven system for the high speed CCL and post-treatment equipment. Drying of the polyester resins using the induction heater and infrared heater showed that the blistering tendency of polyester resin coating increased regardless of additives and colors of resins as the heating rate and/or dry film thickness increased. The blistering of polyester resin coating layer occurred when the heating speed was over than $25^{\circ}C/sec$ for the dry film thickness of $19\~20um$, which is the typical thickness of finish coating in CCL. So did it when the heating speed was over than $40^{\circ}C/sec$ for the dry film thickness over than 10 um. The heating efficiency of paint coated steels by the infrared heating was strongly dependent on the colors of paint coating and generally increased for the dark surface and/or coating. But the faster drying of the PCM resin coatings increased the blistering tendency of coating layer. The blistering limit for the typical finish coating by the infrared heating was estimated as the heating rate slower than $20^{\circ}C/sec$ regardless of colors of PCM resins.

• 한국산업융합학회 논문집
• /
• 제2권2호
• /
• pp.61-68
• /
• 1999

The variety of crystalline structure and mechanical properties of PP filament treated with dry heat treatment at different draw ratio has been studied. Crystalline structure and mechanical properties of annealed PP filament at different draw ratio has been examined by XRD, UTM, and density method. Heat treatment has been carried out $100^{\circ}C$, $120^{\circ}C$ $140^{\circ}C$ for 30min. in dry oven. From the results of this study, it found the following facts. It was found that the crystallinity and crystallite size of (110) plane of sample were increased with increasing of annealed temperature and draw ratio. The crystalline form of annealed sample which was undrawn showed ${\alpha}$, ${\beta}$ mixing form below $120^{\circ}C$ and showed ${\alpha}$ form at $140^{\circ}C$. But the crystalline form of annealed sample which was drawn showed ${\alpha}$ form at $120^{\circ}C$. Initial modulus and tensile strength were increased with increasing of annealing temperature, and the degree of orientation was decreased with decreasing of annealing temperature.

• Journal of the Korean Wood Science and Technology
• /
• 제37권3호
• /
• pp.231-238
• /
• 2009

우리나라에서 전통주택(한옥) 및 목조건축 문화재의 구조부재로 많이 이용되는 소나무는 천연건조가 일반적이어서 건조에 많은 시간이 소요되고 건조가 불충분하면 수축에 의한 갈라짐 및 변형 등의 결함을 일으킬 수 있다. 소나무 소시험편과 대단면 시험편을 제작하여 함수율상태에 따른 수축률변화를 검토하였다. 특정 함수율 상태에서의 체적수축률을 예측할 경우, 생재상태에서 기건상태, 기건상태에서 전건상태까지의 구간으로 나누어 적용하는 것이 정밀도가 높았다. 변재의 체적수축률은 단면크기에는 상관성이 없으며, 심재는 단면이 커질수록 체적수축률이 감소하는 것으로 나타났다.

• 임산에너지
• /
• 제2권2호
• /
• pp.1-12
• /
• 1982

To study tile comparison of aboveground biomass of Pinus rigida Mill. of 18-year-old, plantations located in Whaseong, Yuseong and Wanju district were selected. Ten sample trees in each district selected taking account of DBH distribution were felled carefully to minimize loss of branches and stem analysed by 1m lag segment sectioned from base . The tree height and DBH were measured for sample trees in total growing within $200m^2$ experimental plot. The diagram of oven-dry weight distribution of stem, branch and needle for each 1m segment was constructed. The logarithmic regression equations between dry weight of each component and the two variables, $DBH^2$ and tree height, combined term were presented. The standing crops in the sample stand was estimated to be as much as 23.88, 54.09 and 42.68 tons of dry matter, above ground , per ha in Whaseong, Yuseong anf Wanju district respectively. Annual net production was estimated at 253,657 and 3.65 tons per ha per year respectively. The net assimilation rate was 1.65,1.95 and 1.81 kg/kg/yr in Whaseong, Yuseong and Wanju district respectively. The efficency of leaf to produce stem was 0.99, 1.12 and 1.30 kg/kg/yr respectively.

• 한국지반공학회논문집
• /
• 제34권12호
• /
• pp.29-42
• /
• 2018

대구경북지역 셰일 및 이암은 다른 암석에 비해 강도가 낮고 풍화에 약하므로 이러한 암석의 포화상태나 균열 발달 정도가 강도에 미치는 영향에 대해 분석할 필요가 있다. 이에 본 연구에서는 대구경북지역 토목공사 현장에서 셰일 및 이암을 채취한 다음 흡수율, SEM, 화학성분, 내구성시험과 같은 기본 물성시험을 실시하였으며, 셰일에 비해 이암의 공극률(흡수율)은 31%(25%) 정도로 6(8)배 정도 높은 값을 보였다. 물에 쉽게 풀리는 이암의 경우 활성도가 높은 스멕타이트 군의 점토광물이 많이 포함되어 있는 것으로 나타났다. 채취한 암석을 소형 정육면체로 가공한 다음 일축압축시험을 실시하여 암석의 건조 및 포화 상태에 따른 일축압축강도를 비교하였다. 또한, 전자레인지를 이용하여 암석 공극 내 물을 가열시켜 내부에서 균열이 발생하도록 유도하였으며, 작동시간을 달리하여 내부 균열의 발생 정도에 따른 강도를 비교하였다. 건조된 셰일과 이암의 일축압축강도는 평균 62MPa, 11MPa이며, 이를 포화시키면 일축압축강도는 셰일은 평균 33MPa, 이암은 4MPa로 47% 및 64% 정도 감소하였다. 전자레인지로 15초 작동시켜 균열을 유발할 경우 포화 상태보다 셰일은 49%, 이암은 52% 정도 강도가 감소하였다. 20초 정도 작동 시 대부분의 암석이 여러 조각으로 파쇄되었으며, 이때 소형 암석 내부의 온도는 200도 정도였다.

• 대한화장품학회지
• /
• 제38권2호
• /
• pp.133-138
• /
• 2012

본 연구는 건조된 코아세르베이트 필름의 물리적 특성이 샴푸 건조 후 모발 사용감에 미치는 상관관계를 조사하기 위하여 실시하였다. 단순 샴푸 조성물은 동일한 조성의 계면활성제에 양이온 전하 밀도가 서로 다른 두 종류의 양이온 폴리머를 사용하여 제조하였다. 이 단순 조성물을 물에 희석하여 코아세르베이트(Coacervate)를 형성되도록 하였고, 3000 rpm, 30 min 조건으로 원심 분리하여 형성된 코아세르베이트를 얻었다. 얻어진 코아세르베이트를 유리판 위에 균일한 두께로 도포하고 $50^{\circ}C$ 건조기에서 1 h 건조하여 코아세르베이트 필름을 얻었다. 이렇게 얻어진 코아세르베이트 필름의 접촉각과 코아세르베이트의 SEM 이미지 조사를 수행하였고, 코아세르베이트의 수분 보유량과 수분 유지력을 동시에 조사하였다. 샴푸 후 건조된 모발의 부드러움과 보습감은 모발타래를 이용하여 전문 미용 패널이 평가를 수행하였다. 본 실험결과 건조된 코아세르베이트 필름의 특성이 샴푸 후 건조된 모발의 부드러움 및 보습감에 영향을 주는 것으로 확인되었다.