• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.10
• /
• pp.2690-2698
• /
• 1995

Fuel atomization and mixture formation in an gasoline engine has influence on the engine performance and pollutant emission. The throttle valve installed in an intake system plays a greater role in control of mixture quantity in accordance with engine drive condition. In this study, the characteristics of secondary atomization developed at the downstream of the valves were observed using an image processing method. Two major kinds of valves, solid and perforated ones, are chosen in order to compare the valve performance with the experimental parameters of air flow rate, valve opening angle, and valve shapes. For the perforated valve, we can obtain the relatively small sized droplets, and nearly uniformed and dense distributed sprays with low loss coefficient than for the solid valve.

• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.1-9
• /
• 1998

Two measurement techniques of droplet sizing, an imaging technique(PMAS) and a phase-Doppler measurement technique (PDPA), have been compared using a water spray from a pressurized-type swirl nozzle. The result showed that SMD measured by PDPA was larger than that measured by PMAS by about 40 %. Such discrepancy of SMD could be explained by the fact that the light signal intensity used by PDPA can be biased towards larger particles. On the other hand there could be lower opportunity to capture the images of the large particles with PMAS, since the large particles could be out of sight due to their high speed.

• Journal of the Korean Society of Visualization
• /
• v.21 no.1
• /
• pp.94-102
• /
• 2023

Three design parameters were considered in this study: outlet nozzle angle (30°, 60°, 80°), neck length (1 mm, 3 mm), and flow rate (0.5, 0.6, 0.7, 0.8 lpm). A neck diameter of 0.5 mm induced cavitation flow at a venture nozzle. A secondary transparent chamber was connected after ejection to increase bubble duration and shape visibility. The bubble size was estimated using a Gaussian kernel function to identify bubbles in the acquired images. Data on bubble size were used to obtain Sauter's mean diameter and probability density function to obtain specific bubble state conditions. The degree of bubble generation according to the bubble size was compared for each design variable. The bubble diameter increased as the flow rate increased. The frequency of bubble generation was highest around 20 ㎛. With the same neck length, the smaller the CV number, the larger the average bubble diameter. It is possible to increase the generation frequency of smaller bubbles by the cavitation method by changing the magnification angle and length of the neck. However, if the flow rate is too large, the average bubble diameter tends to increase, so an appropriate flow rate should be selected.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.130-130
• /
• 2016

Bioinspired hierarchical nanostructures for self-cleaning s-tnwjurface and SERS substrates are investigated. The multi-level hierarchy is combined with CuO nanowire and additional nanoscale structures. CuO nanowire, which has extremely high aspect ratio, serves as a base structure of multi-level hierarchy and additional flower like structures are placed on the CuO nanowires. Since as-fabricated CuO nanostructures are hydrophilic, the surface is coated with perfluorooctyltrichlorosilane in order to change its wetting property to hydrophobic. While those CuO based nanostructures have a sufficient roughness for superhydrophobic characteristics, hierarchical nanoflowers on nanowire structures lead to a self-cleaning surface. Furthermore, flower like nanostructures provide reentrant curvatures, thus enabling oleophobic property. The surfaces has a repellency even for a tiny droplet (10 nL) of low surface tension liquids (~35 mN/m). On the on hands, nanoflowers provide many number of nanoscale gaps. After a thin layer of silver is deposited on the surface of CuO nanostructures, those nanoscale gaps act as hot-spot for surface enhanced Raman scattering (SERS). To analyze SERS enhancement of the surfaces, Raman shift is measured with varying molar density of 4-Mercaptopyridine from mM to pM. From these results, hierarchical CuO nanostructures are suitable for self-maintenance and cost effective SERS sensing applications.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.3
• /
• pp.50-57
• /
• 2007

Spray characteristics of an injector in a small liquid rocket engine (LRE) is characterized by Particle Image Velocimetry (PIV) and Dual-mode Phase Doppler Anemometry (DPDA). Instantaneous plane images captured by PIV are examined for the qualitative prediction of spray breakup with the setup of evaluation technique for effect of spray angles on injector performance. DPDA is also applied in order to quantify the average velocity, turbulent intensity, SMD, and number density of spray droplets along the spray stream distance leading to precise observation of spray atomization behavior. An objective of the study is the derivation of design parameters of new injectors and the establishment of performance criteria through the clear understanding of spray characteristics.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.120-127
• /
• 2021

Purpose: In this study, the effect of changes in the variables related to water droplets on the spray density on the floor in the analysis of the water mist fire protection system using FDS was analyzed. Method: When the spray of the water mist nozzle was analyzed in FDS, Particles Per Seconds, Particle Velocity, Size Distribution, and Spray Pattern Shape that can be set in relation to droplets were input to review the analyzed results. Result: In the analysis results, when the number of particles per second was set above a certain value, the spray density of the floor was similar. In the case of Particle Velocity, as the velocity decreases, the spray density of the central portion increases but decreases at a distance of 0.15m or more. From the analysis of the change in the size distribution function, it was found that an increase in the 𝛾 value increases the spray density of the central part, but the value at a remote location decreases. Compared to the result of applying the Gaussian distribution, the median value decreases dramatically when the uniform distribution is applied, but the value at the adjacent position increases. Conclusion: Variables related to the droplet properties of the FDS affect the spray density of the floor. Therefore, in order to increase the reliability of results before performing analyses such as fire suppression or cooling, a sufficient review of input variables is required.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.72-79
• /
• 2003

Spray characteristics were investigated by impinging F-O-O-F type injector with varying the impingement angle through 15, 20 and 30 degree and the mixture ratio(O/F ratio) from 1.5 to 3.0. Experimental results show that the correlation between dispersion and impingement angle is not influenced of the mixture ratio variation, but which has influence on number density, and there is a linear correlation between dispersion and impingement angle. Velocity distribution, standard deviation and SMD of droplets are decreased as the impingement angle increases. Also, it was confirmed that the distribution of droplet size are in accordance with Rosin-Rammler and Upper-limit distribution.

• Korean Journal of Animal Reproduction
• /
• v.17 no.4
• /
• pp.271-278
• /
• 1994

The aim of this study was to compare the two culture systems 1) co-culture with cumulus cells and 2) chemically defined medium supplemented with amino acids (CR1aa) and fetal calf serum (FCS) of in vitro produced bovine embryos from follicular oocytes in vitro. Bovine follicular oocytes were collected from ovaries of slaughtered cows and matured in TCM199 supplemented with 10% FCS and hormones (1$\mu\textrm{g}$/ml FSH-P and 1$\mu\textrm{g}$/ml oestradiol-17$\beta$)24 hours at 39$^{\circ}C$ under 5% CO2 in air. The capacitation of spermatozoa from ejaculated or frozen bull semen was induced by centrifugation through Percoll density gradient (45%, 90%). Then capacitated spermatozoa (1$\times$106/ml) were inseminated into 50${mu}ell$ droplet containing matured follicular oocytes and incubated for 40~42 hours. Cleaved embryos of 2~4cell stage were transferred to the co-culture with cumulus cells and/or CR1aa medium supplemented with FCS. In semen source, the developmental rates to the blastocyst and the hatched blastocyst stages were higher in ejaculated semen(27.6% and 14.9%) than those of frozen-thawed semen(18.3% and 11.8%), respectively. In two culture systems, the proportions of embryonic development upto the blastocysts and the hatched blastocysts were higher of CR1aa medium (22.1% and 12.1%) than those of cumulus cell co-culture (16.8% and 5.1%), respectively. The number of cells in exapnded blastocysts was slightly higher in cumulus cells co-culture (122.6$\pm$8.5) than that in CR1aa medium (117.9$\pm$5.9). The present results indicated that the early development of in vitro produced bovine embryos can be maintained efficiently in CR1aa medium as well as in co-culture with cumulus cells.