• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.10
• /
• pp.805-811
• /
• 2016

Prior to installation in a navy ship, shipboard equipment should be qualified by shock test requirements. The multi-function console mounted on the elastic platform of the ship should also withstand given shock loads. In this study, both real shock test methods, as well as numerical computer simulations using the finite element method were used to verify structural durability under shock load conditions. First, we used domestic test facilities to perform possible shock tests, including an impact hammer test, a drop table test and a shaker shock test. Full model tests satisfying the shock response spectrum level were performed. Thereafter, an analytical model of the complex console structure was built by the finite element method. Finally, numerical results were verified by modal test results of the real product and an FEA analysis was also performed with a full model transient response analysis.

• Composites Research
• /
• v.15 no.2
• /
• pp.11-17
• /
• 2002

The piezoelectric thin film sensor can be used to interpret variations in structural and material properties, e.g. for structural integrity monitoring and assessment. To illustrate one of this potential benefit, PVDF (polyvinylidene fluoride) film sensors are used for monitoring impact damage in Gr/Ep composite panels. Both PVDF film sensors and strain gages are attached to the surface of Gr/Ep specimens. A series of impact tests at various impact energy by changing impact mass the height are performed on the instrumented drop weight impact tester. The sensor responses are carefully examined to predict the onset of impact damage such as indentation, matrix cracking, and delamination, etc. Test results show that the particular waveforms of sensor signals implying the damage initiation and development are detected above the damage initiation impact energy. As expected, the PVDF film sensor is found to be more sensitive to impact damage initiation event than the strain gage.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.2
• /
• pp.5-12
• /
• 2022

In this study, a field test was conducted to present a test method for performance evaluation of a rock fall prevention fence, centering on the vertical drop test among the existing test methods of the rock fall prevention fence. A test to determine the support capacity of a rockfall prevention fence in Korea is usually conducted using a combination of wire mesh, poles, and wire rope, and the location of the impact of falling rocks has been conducted centered on the center of the wire mesh. However, in the case of domestic papers and test data, there is no data on direct hit of post. Therefore, the amount of displacement and weak section were analyzed when the impact on 100kJ class rock energy was hit on the post, centering on the Rockfall Protection fence (highway type No. 2).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.5963-5967
• /
• 2014

Reducing the impact of collisions of cars is a major issue for reducing the injury and death of passengers. According to the statistical data of the Road Traffic Authority, the deaths from side collision accidents caused by the collision of passenger cars is greater than the deaths from head-on collision accidents. To accommodate this, vehicle designers have added a reinforcing material called the impact frame and impact beam on the inside of the door. Many experiments are needed to develop the door impact beam. These reinforcements to develop a collision experiment is essential. Collision experiments are costly and time consuming. This study used a drop Impactor to obtain the impulse and a strain experimental device was developed for this purpose. The economic costs were reduced and the ideal experiment device configuration was determined. A comparison of the experimental results with numerical value analysis revealed $3.5{\tiimes}10-3sec$ strain ranging from $3.49{\tiimes}10-3$ to $3.99{\tiimes}10-3$.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.1
• /
• pp.55-62
• /
• 2003

This study has investigated physical and chemical properties of FRP waste, has manufactured polymer cement mortar using a crushed waste with sand and has evaluated its capability to develop the economical waste recycling technology. The study has investigated tension strength, hardness test and impact test as physical properties and also thermogravimetric characteristics and analyzed infrared spectroscope as chemical properties. Then the study has manufactured polymer cement mortar and has analyzed how the FRP waste fine aggregate replacement ratio has an effect on compression strength. Noticing admixture can complement strength drop occurred by the FRP waste fine aggregate replacement, the study examined an optimum rate of admixture addition and its reaction through electron microscope photos.

• Journal of the Korean Society of Safety
• /
• v.28 no.4
• /
• pp.91-96
• /
• 2013

Forklift truck is one of the dangerous machines which causes the fatal accidents most frequently. The causes of fatalities by forklift from 2008 to 2011 were analyzed. Crushing the operator when tipping over or falling off a truck were the major causes of death in this study. The purpose of this study is to show measures from the engineering point of view to prevent the forklift truck accidents. In order for that, the domestic requirement for forklift safety was compared with those of foreign and international standards. The manufacturers' opinion was also collected regarding to improve the forklift safety. Several measures were suggested in order to prevent fatalities caused by forklift.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.147-149
• /
• 1987

On the colling mill plant, the qulity of products depends on the ability to follow up the command of roll speed and the magnitude of impact drop. In this paper, the frequency response method is applied to the main motor system of No.1 Plate Mill Plant in POSCO. This paper show the influences when the pseudo random noise as test signal is applied to the system to be measured and presents the proper magnitude of test signal.

• Proceedings of the Safety Management and Science Conference
• /
• 2013.04a
• /
• pp.41-52
• /
• 2013

Forklift truck is one of the dangerous machines which causes the fatal accidents most frequently. The causes of fatalities by forklift from 2008 to 2011 were analyzed. Crushing the operator when tipping over or falling off a truck were the major causes of death in this study. The purpose of this study is to show measures from the engineering point of view to prevent the forklift truck accidents. In order for that, the domestic requirement for forklift safety was compared with those of foreign and international standards. The manufacturers' opinion was also collected regarding to improve the forklift safety. Several measures were suggested in order to prevent fatalities caused by forklift.

• Steel and Composite Structures
• /
• v.46 no.4
• /
• pp.525-538
• /
• 2023

This paper focuses on the energy absorption of lattice core sandwich structures of different configurations. The diamond lattice unit cell, which has been extensively investigated for energy absorption applications, is the starting point for this research. The energy absorption behaviour of sandwich structures with an expanded metal sheet as the core is investigated at low-velocity impact loading. Numerical simulations were carried out using ABAQUS/EXPLICIT and the results were thoroughly compared with the experimental results, which indicated desirable accuracy. A parametric analysis, using a Box-Behnken design (BBD), as a method for the design of experiments (DOE), was performed. The samples fabricated in three levels of parameters include 0.081, 0.145, and 0.562 mm² Cell sizes, and 0, 45, and 90-degree cell orientation, which were investigated. It was observed from experimental data that the angle of cells orientation had the highest degree of influence on the specific energy absorption. The results showed that the angle of cells orientation has been the most influential parameter to increase the peak forces. The results from using the design expert software showed the optimal specific energy absorption and peak force to be 1786 J/kg and 26314.4 N, respectively. The obtained R2 values and normal probability plots indicated a good agreement between the experimental results and those predicted by the model.

• Elastomers and Composites
• /
• v.57 no.4
• /
• pp.157-164
• /
• 2022

Representative bulletproof materials, such as aramid or ultra-high molecular weight polyethylene(UHMWPE), have excellent strength and modulus in the plane direction but are very vulnerable to forces applied in the thickness direction. This paper reports a study on the effects of reinforcement in the thickness direction when bulletproof composite fabrics are prepared to improve their performance. Aramid and UHMWPE fabrics were combined using the film-bonding, needle-punching, or stitching methods and then subjected to low-velocity projectile and ball-drop impact tests. The results of the low-velocity projectile test indicated that the backface signature(BFS) decreased by up to 29.2% in fabrics obtained via the film-bonding method. However, the weight of the film-bonded fabric increased by approximately 23% compared with that obtained by simple lamination, and the fabric stiffened on account of the binder. Flexibility, light weight for wearability, and excellent bulletproof performance are very important factors in the development of bulletproof materials. When the needle-punching method was used, the BFS increased as the fibers sustained damage by the needle. When the composite fabrics were combined by stitching, no significant difference in weight and thickness was observed, and the BFS showed similar results. When a diagonal stitching pattern was employed, the BFS decreased as the stitching density increased. By contrast, when a diamond stitching pattern was used, the fabric fibers were damaged and the BFS increased as the stitching density increased.