• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.8
• /
• pp.733-741
• /
• 2013

This is the first paper on the combustion characteristics of landfill gas in a constant volume combustion chamber for a large displacement volume commercial engine, and it discusses the fundamental characteristics of fuel from the viewpoint of thermochemistry and thermodynamics and compares these results with experimental ones. The results show that the final pressures obtained from theoretical analysis vary under the same heating value owing to the change in the constant volume specific heat owing to the difference in the burned gas composition according to the fuel gas compositions; furthermore, the stoichiometric ratios and trends of analytical and experimental pressures coincide very well, although some minor differences are observed between the two. The root cause of the difference is the heat transfer, which changes the specific heat and lowers the temperature considerably, in the real combustion process. In addition, the large chamber volume and ignition position promote the heat transfer to the wall. Finally, the fuel conversion efficiency increases as the methane mol fraction decreases, and it is maximum when the stoichiometric ratio ranges from 0.8 to 0.9. These increases due to the composition and stoichiometric ratio could sufficiently compensate the decrease due to the specific heat ratio drop, LFG might be more advantageous than pure methane in a real engine.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.19 no.3
• /
• pp.130-139
• /
• 2017

The crop damage caused by strong wind was predicted using the wind speed data available from Korean Meteorological Administration (KMA). Wind speed data measured at 19 automatic weather stations in 2012 were compared with wind data available from the KMA's digital forecast. Linear regression equations were derived using the maximum value of wind speed measurements for the three-hour period prior to a given hour and the digital forecasts at the three-hour interval. Estimates of daily maximum wind speed were obtained from the regression equation finding the greatest value among the maximum wind speed at the three-hour interval. The estimation error for the daily maximum wind speed was expressed using normal distribution and Weibull distribution probability density function. The daily maximum wind speed was compared with the critical wind speed that could cause crop damage to determine the level of stages for wind damage, e.g., "watch" or "warning." Spatial interpolation of the regression coefficient for the maximum wind speed, the standard deviation of the estimation error at the automated weather stations, the parameters of Weibull distribution was performed. These interpolated values at the four synoptic weather stations including Suncheon, Namwon, Imsil, and Jangsu were used to estimate the daily maximum wind speed in 2012. The wind damage risk was determined using the critical wind speed of 10m/s under the assumption that the fruit of a pear variety Mansamgil would begin to drop at 10 m/s. The results indicated that the Weibull distribution was more effective than the normal distribution for the estimation error probability distribution for assessing wind damage risk.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.1
• /
• pp.54-62
• /
• 2015

Small scale paint overspray booths are being operated nationwidely, for repair of passenger car body parts. paint aerosols are emitted from the paint overspray booth in operations. In paint overspray booth operations without ventilation system and air pollutants collection unit, it may land on nearby equipment. In this study a removal of sticky paint aerosol for application of the small-scale overspray paint booth. it's cause the surface of filter bag from generated sticky paint aerosol. To remove adhesion of paint aerosol the agglomerating agents are injected and mixed with sticky paint aerosols prior to reach the filter bag. The paint spray rate was set as $10{\pm}5g/min$ from air-atomized spray guns in the spray booth, injection rate of agglomerating was $10{\pm}5g/min$ in the mixing chamber. The filtration velocity including air pollutants varied from 0.2 m/min to 0.4 m/min. Bag cleaning air pressure was set as $5.0kg_f/min$ for detaching dust cake from surface of filter bag. Bag cleaning interval at the filtration velocity of 0.2 m/min was around 3 times longer than that of the 0.4 m/min. The residual pressure drop maintained highest value at the highest filtration velocity. Fractional efficiency of 99.952%~99.971% was possible to maintain for the particle size of 2.5 microns. Total collection efficiency at the filtration velocity of 0.2 m/min was 99.42%. During this study we could confirm high collection efficiency and long cleaning intervals for the test with filtration velocity of 0.2 m/min indicating an optimal value for the given dimensions of the test unit and test operating conditions.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.65-71
• /
• 2019

Conventional methods of measuring ground resistance and ground resistance field measurement are used to measure voltage drop according to the resistance value of the site by applying current by installing a constant interval of measurement electrode. If the stratified structure of the site site is unique, errors in boundary conditions will occur in the event of back acid and the analysis of the critical ground resistance in the ground design will show much difference from simulation. This study utilizes the Arduino module and smart ground measurement technology in the convergent information and communication environment to develop a reliable smart land resistance measuring device even if the top layer of land is unique, to analyze the land resistance and accumulate data to predict the change in the age of the land. Considering the topographical characteristics of the site, we propose a ground resistance measuring device and its method of measuring ground resistance so that the auxiliary electrode can be installed by correctly positioning the angle and distance in measuring ground resistance. Not only is ground resistance value obtained through electrodes installed to allow accurate ground resistance values to be selected, but it can also be used as a useful material for installing electrical facilities in similar areas. Moreover, by utilizing reliable data and analyzing the large sections of the site, a precise analysis of the site, which is important in ground design as well as construction cost, is expected to be used much in ground facility design such as potential rise.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.923-928
• /
• 2015

The FDS is one of the most used programs for fire analysis and needs an optimal grid selection for an accurate analysis. This study selected various grid aspect ratios (ARs) for selection of optimal grid and analyzed them with FDS v 6.1.2. A calculation time of 10 min. was used, which is enough to obtain the time average value of temperature changes. Temperature, visibility, and the time average value of mass balance are obtained from 200-600 s, which is a period of maintaining quasi-steady state. Two polyurethane fires of 1 [MW] and 2 [MW] in two enclosures of $10{\times}10{\times}3[m^3]$ and $20{\times}20{\times}3[m^3]$ were considered. Time variations of heat release rates, temperature, visibility, and mass balance were compared for ARs from 1-6. The heat release rates were accurate for all aspect ratios regardless of fire and enclosure sizes. The quasi-steady state temperature and visibility were well predicted for $AR{\leq}5$. Temperature drop and skewness of mass conservation, however, increased with increasing aspect ratio. Therefore, careful investigation of the grid size is recommended in performance-based design when $AR{\geq}3$, where temperature and visibility in early stage of a fire are important parameters. For accurate simulations of enclosure fires, grid sizes of 0.1~0.2 [m] and smaller in the vertical direction and $AR{\leq}2$ are recommended.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.567-573
• /
• 2015

This paper aims to evaluate the variation in the mechanical properties of carbon/epoxy composites under in situ low- and high-temperature environments. In situ low- and high-temperature environments were simulated with temperature ranging from $-40^{\circ}C$ to $220^{\circ}C$ using an environmental chamber and furnace. The variation in the mechanical properties of the composites was measured for longitudinal and transverse tensile properties, in-plane shear properties and interlaminar shear strength. Under the low temperature of $-40^{\circ}C$, all mechanical properties increased moderately compared to the baseline properties measured at room temperature. The changes in the longitudinal tensile properties decreased moderately with increasing temperature. However, transverse tensile properties, in-plane shear properties and interlaminar shear strength each showed a significant drop due to the glass transition behavior of the matrix after $140^{\circ}C$. Notably, the tensile property value near $100^{\circ}C$ increased compared to baseline property value, which was an unusual occurrence. This behavior was a direct result of post-curing of the epoxy resin due to its exposure to high temperature.

• Membrane Journal
• /
• v.24 no.3
• /
• pp.231-239
• /
• 2014

Polyetherimide (PEI) membranes for separators in Zn air batteries were prepared via phase inversion process from casting solution composed of PEI, n-methylpyrolidone (NMP), and polyvinylpurrolidone (PVP). Furthermore, Zn air batteries were fabricated with the separators. The effects of PEI content and PVP addition in the casting solution on the morphology, mechanical strength, ionic conductivity were investigated through SEM, stress-strain test and ac impedance test. The elelctrochemical performances of the batteries were evaluated through galvanostatic discharge analysis. The mechanical strength of the membrane increased with increasing PEI composition in the casting solution. Little effect of PVP addition into the solution on the mechanical strength of the membrane was investigated. The ionic conductivity value decreased with increasing PEI composition in the solution. With addition of PVP, ionic conductivity of membrane increased until 10 wt% to show the maximum value of 0.1 S/cm. In the higher range of PVP addition over 10%, the ionic conductivity decreased with increasing PVP addition. Ionic conductivity of separator strongly affected the capacity of Zn air battery, and the battery assembled with the separator which showed high ionic conductivity showed high capacity.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.5
• /
• pp.421-428
• /
• 2016

In this work, pozzolanic activities of various waste materials were compared with those of well-known by-product pozzolanic materials. Undensified and densified silica fume, ASTM class F and class C fly ash, and metakaolin were chosen as well-known pozzolanic materials, and bentonite powder, ceramic powder obtained from wash basin, and waste glass wool, which can possibly possess pozzolanic property, were chosen for comparison. Drop in electrical conductivity at $40^{\circ}C$ saturated lime solution was measured for each materials. The amount of Ca(OH)2 decomposed from cement paste at $450{\sim}500^{\circ}C$ was also measured to evaluate pozzolanic activity. The 28 day compressive strength were used to observe the mechanical property enhanced by incorporation of various waste materials. According to the experimental results, using "difference between maximum conductivity value and conductivity value at 4 hour" was found to be a reasonable approach to determine pozzolanic activity of a material. Pozzolanic activity measured using electrical conductivity correlates very well with that measured using the amount of Ca(OH)2 remained in the cement paste. Relatively good agreement was also found with electrical conductivity and 28 day compressive strength. It was found that electrical conductivity measurement can be used to evaluate pozzolanic activity of unknown materials.

• Journal of the East Asian Society of Dietary Life
• /
• v.19 no.6
• /
• pp.928-934
• /
• 2009

The purpose of this study was to examine the possibility of making functional sulgitteok with Goami 2 rice, which is a rich that is high in dietary fiber. Sulgitteok was made by adding various amounts of Goami powder(25, 50, 75, and 100 %) to rice powder. Then, the sensory tests and other tests to measure color, texture and hardness were examined as a function of time and the moisture content in sulgitteok was measured to determine the quality and characteristics of different types of sulgitteok. The conclusions of these tests were as follows : In the sensory evaluation preference test of sulgitteok made with various amounts of Goami powder, the overall preference was the highest in sulgitteok made with 50% Goami powder (S2). In the difference test, the higher the amount of added Goami powder, the lower the grades were. The S4 group, which was made with Gomai powder, had a strongly unique odor compared with those made with rice powder, which smelled weaker. In terms of the color values of Gomai added sulgitteok, the higher the amount of added Gomai powder, the lower the lightness value of sulgitteok, where group S4 had the lowest value. In addition, the S4 group, which was made with Goami powder, had the hightest red and yellow color. The texture test indicated that sulgitteok containing a large amount of Goami powder were considerably harder compared with the control group. While every group containing Goami powder (S1, S2, S3 and S4) became harder during the first to the third day of the test, their hardness tended to drop after longer storage times. In the control group, the hardness continued to grow from the start up to the fifth day. After five days' there was a noticeable change in the moisture content in the different types of sulgitteok, with more water evaporating in the S3, S2, and S1 groups than in the S4 groups, which contained the highest amount of Goami powder. Group C, which contained no Goami powder, had the largest water evaporation. Sulgitteok that contained more Goami powder turned out to be more savory than baekseolgi made solely of rice powder. However, they were less preferable overall, since they were rated lower in terms of color, texture and other characteristics. Therefore, utilize Goami tteok as a functional ingredient in food for people with diabetes or obesity, further studies on additives that can provide a sticky texture and favorable color should be conducted. In addition, different types of ttoek such as pounded or boiled ones may be preferable to sulgitteok.

• Journal of Korean Society of Forest Science
• /
• v.99 no.3
• /
• pp.292-297
• /
• 2010

This study was carried out to provide preliminary data to purify contaminated sites by nickel (Ni). After rooted cuttings of Salix reichardtii had been grown in Ni solution (hydroponic culture), pH changes in the solution and the accumulated Ni amount in plant parts were measured and analyzed. When the Ni concentration was low enough for S. reichardtii cuttings to grow well, the pH value of the solution decreased considerably. As the Ni concentration got higher, the plant growth got poorer and the pH value decreased slowly. Roots accumulated the highest Ni amount. Leaves and stems followed after. When stems were older, the accumulated Ni amount was lower. more Ni was accumulated in the plant parts which had more flexible tissue and live cells. As the Ni concentration in solution got higher up to 50.0 ${\mu}mol$/L, so did the Ni accumulation in the plant parts. However, the plant individuals nearly died and the Ni accumulation tended to drop when the Ni concentration in solution was 100.0 ${\mu}mol$/L. The rooted cuttings of S. reichardtii grew poorer as the Ni concentration in solution got higher. The plants in solution with 100.0 ${\mu}mol$/L of Ni were practically dead in four weeks.