• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.4
• /
• pp.315-320
• /
• 2010

To improve not only the basic performance but also the fail-safe performance, power consumption of the main landing gear for helicopters, a semi-active control landing gear using hybrid MR damper, was introduced in this paper. This damper of the configuration to install a permanent magnet in a electromagnet MR damper, was designed by the trade-off study on permanent magnet location and a magnet field analysis. Force control algorithm which keep the sum of air spring force and damping force at a specified value during landing, was used for the controller. The drop simulations using ADAMS Model for this semi-active control landing gear, were done. The improvement of the preceding performances as the result to evaluate the landing performance by the simulations, has been confirmed.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.45 no.2
• /
• pp.195-202
• /
• 2018

The purpose of this study is to analyze the cariogenicity of vitamin supplements for children by the Caries Potentiality Index (CPI), pH drop capacity, proliferation rate of Streptococcus mutans. Four vitamin supplements were selected - Noma (NM), Cenovis Kids (CK), Animal Parade (AP), and Character Vitamin (CV). CPI value decreased in the order of AP, CV, CK, and NM. Initial values of all experimental groups showed acidity below pH 7.0. Analysis of the colony forming units of Streptococcus mutans showed that NM and CV resulted a higher proliferation rate (p < 0.05) than CK and AP (p < 0.05). Bacterial activity of the control group was lower than other groups when observed with a confocal laser scanning microscope. Considering the bacterial activity and acidity of vitamin supplements, it is necessary to pay close attention when children taken the vitamin supplements for their oral health.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.567-570
• /
• 2008

The present study investigated the applicability of the minium fludization velocity measuring method using linear regression analysis between the standard deviation of pressure fluctuation and gas velocity in multi-particle sand on a fluidized bed 0.109 in inner diameter. We measured minium fludization velocity according to the standard deviation of particle distribution in Gaussian distribution. The measured value compared with other researchers' equations. The minium fludization velocity derived from the linear regression analysis of the standard deviation of pressure fluctuation and pressure drop inside the bed. We also found that the minium fludization velocity of a multi-particle system using the standard deviation of pressure fluctuation must be measured at freely bubbling region.

• Journal of the Korean Home Economics Association
• /
• v.45 no.4
• /
• pp.43-51
• /
• 2007

This study analyzed the knit wear trend, which has gained attention as a sensuous and luxury item, through collection magazines, and used the technique of hand-knit to produce and present the knit wear that was designed based on the study results. Accordingly, the purpose of this study is to raise awareness of the expansion of hand knit's new expression techniques and expression areas and to verify its possibility as a higher value-added product. The trends of hand-knit wear resulted from the analysis of collections divided into the following four groups, and the knit designs were also grouped accordingly: First was "The design using object." The trend survey showed the results that the form of drops or flowers was often used as a factor of object. Accordingly, as for the study design, the drop-knitting technique, which is one of the pattern knitting techniques, was used to present a design that employed drops as the object. Second was "The design matched with woven material." It is a way to emphasize aesthetic formativeness and at the same time to activate the area of knit design by matching woven material, which is different from knit in texture, with knit. This study presented a design that tried to combine knit texture and woven material by connecting denim material with various textures and colors. Third was "The design to express see-through." A sense of showing through knit wear was expressed through changes in the type of thread or knitting technique. In this study, the sense of see-through was expressed using piano wires and wool threads and through changes in the thickness of needle. Fourth was "The design to emphasize coloring." It was analyzed that regarding the production of hand knit, the method of coloring expression was to express points, lines and sides or to create harmony by changing the material's color or texture to show particular objects or shapes. In this study, a jacket was designed using the method to express points, lines and sides by changing the material's color.

• Journal of the Korean earth science society
• /
• v.28 no.2
• /
• pp.179-186
• /
• 2007

The response spectrum is one of the important basic materials for the aseismic design. Numerous strong ground motions based on the seismic source characteristics for the earthquakes occurring in the Korean Peninsula were simulated to obtain the response spectra by using the computer program, SMSIM, developed by Boore (2005). Through the extensive review of other study outcomes, the input data for the simulation such as seismic source and attenuation characteristics were selected. The spectra obtained from the simulated ground motions were normalized to 1.0 g of zero period acceleration and compared with the standard response spectrum proposed by the U.S. Atomic Energy Commission (AEC, 1973). In this study, we found that the spectral values for the response spectra appeared to be larger than those of the standard spectrum in the frequency band above roughly 10 Hz. The variation of resulting response spectra was evaluated with the variable stress drops. It was shown that the spectral amplitude of the spectrum for the larger stress drop denotes higher value in the low frequency range.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.6
• /
• pp.535-542
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effect of bed insert geometry on CO conversion of WGS catalyst was measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and tablet shaped WGS catalyst and sand particle were used as bed materials. The cylinder type and the spring type bed inserts were used to hold the WGS catalysts. The CO conversion of WGS catalyst with the change of steam/CO ratio was determined based on the exit gas analysis. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. The measured CO conversion using the bed inserts showed high value comparable to previous results even though at low catalyst content. Most of input gas flowed through the bed center side when we charged tablet type catalyst into the cylinder type bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. However, the spring type bed insert showed good reactivity and good distribution of gas, and therefore, the spring type bed insert was selected as the best bed insert for SEWGS process.

• Convergence Security Journal
• /
• v.13 no.3
• /
• pp.25-31
• /
• 2013

Looking at the recent value change of users and the usage pattern of network users, it is changing from simple web information, one-way information acquisition and data transmission to increase of usage of multimedia, increasing demand for security and customization, and increasing demands for free mobility. Due to this change of demand, the services which were provided individually, developed into a form which is merged, the network also seems to develop into the combined network from the individual network for individual service, and the communication network control technology which is the core technology is also rapidly developing. To reflect the users' demands, the next generation network created the multi-layer network which is based on the WDM/IP transmission system and added the to make it easy to restructure. P-OTS (Packet-Optical Transport System) can be defined as a platform that combines SONET/SDH, Ethernet, DWDM, optical transport network (OTN) switching and reconfigurable optical add-drop multiplexers (ROADMs). In this paper, we suggested that the optimum path choice be performed through diversification of the PCE-based path selection using the information of various layers altogether in the multi-layer environment, compared with the established path selection method when the path was selected using the information of each layers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.250-254
• /
• 2016

Currently, power conversion system which converts AC to DC Power is applied in domestic urban railway. The diode rectifier is used in most of them. However the diode rectifier can not control the output voltage and can not regenerate power as well. On the other hand, PWM (pulse width modulation) converter using IGBT (isolated gate bipolar transistor) can control output voltage, allowing it to reduce the output voltage drop. Moreover the Bi-directional conduction regenerates power which does not require additional device for power regeneration control. This paper compared the simulation results for the DC power supply system on both the diode rectifier and the PWM converter. Under the same load condition, simulation circuit for each power supply system was constructed with the PSIM (performance simulation and modeling tool) software. The load condition was set according to the resistance value of the currently operating impedance of light rail line, and the line impedance was set according to the distance of each substations. The train was set using a passive resistor. PI (proportional integral) controller was applied to regulate the output voltage. PSIM simulation was conducted to verify that the PWM Converter was more efficient than the diode rectifier in DC Traction power supply system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.905-910
• /
• 2013

The flow analysis has been made by applying the turbulent models in the helically coiled tubes of heat transfer. The k-${\varepsilon}$ and Spalart-Allmaras turbulent models are used in which the structured grid is applied for the simulation. The velocity vector, the pressure contour, the change of residuals along the iteration number and the friction factors are simulated by solving the Navier-Stokes equations to make clear the Reynolds number effect. The helical tube increases the centrifugal forces by which the wall shear stress become larger on the outer side of the tube. The centrifugal force makes the heat transfer rate locally larger due to the increase of the flow energy, which finds out the close relationship between the pressure drop and friction factor in the internal flow. The present numerical results are compared with others, for example, in the value of friction factor for validation.

• Journal of the Korean Society of Tobacco Science
• /
• v.28 no.1
• /
• pp.43-50
• /
• 2006

The objective of the present study is to induct the regression equation for the hardness prediction of cellulose acetate filter which was manufactured by the domestic cellulose acetate tow manufacturer. As a result of our study, the hardness of filter was increased with increasing the plasticizer content and packing density as major factors affecting to the filter hardness. As a result which was obtained by the three dimensional response surface methodology in STATISTIC A program, the hardness prediction value well fitted with experiment result on the high plasticizer content. To make up for the this equation, the new modified fraction of solid factors which was contained the mono denier factor was introduced to the hardness prediction equation, and this third regression equation which was sufficient for the wide plasticizer content, was obtained by the three dimensional response surface methodology in STATISTICA. This results indicated that the third regression equation which was obtained this study was applicable for the hardness prediction of cellulose acetate filter which was manufactured by the domestic cellulose acetate tow manufacturer.