• 한국정밀공학회지
• /
• 제12권6호
• /
• pp.80-86
• /
• 1995

A method of eliminating the branch problem in driving crank center point plane for 3 position synthesis of 4 bar mechanism is introduced. By studying various transformation characteristics from the circle point plane into the center poi t plane, the curves in the center point plane transformed from the filemon line in circle point plane are analytically obtained, which will seperate the whole center point plane into many sub-areas for the selec- tion of the center point of the driving crank. And a simple method to identify which of the sub-areas will cause the branch problem is also presented. The method will allow the selection of the center point of driving crank without the branch problem.

• 한국ITS학회 논문지
• /
• 제23권1호
• /
• pp.26-41
• /
• 2024

안전한 도로교통 환경 조성을 위하여 운전행동에 영향을 미치는 인적요인에 관한 연구가 필요하지만, 실제 주행행태에 영향을 미치는 개인별 인적요인 특성을 도출하기에는 많은 어려움이 있다. 이에, 개별 운전자의 자기 보고를 통하여 도출되는 위험운전성향을 분석하여 주행 행태 특성과 상관성이 있는지 확인하고, 교통상황에 따른 주행행태에 영향을 미치는 운전성향을 추정하는 방법을 제시하고자 하였다. 본 연구에서는 기존에 고안된 설문 기법을 활용하여 실험 참가자들의 위험운전성향을 여러 방법으로 도출하고, 가상환경 기반의 주행 시뮬레이터 실험을 통하여 도출된 주행행태 특성을 분석하여 위험운전성향과 주행행태 특성 간 유의미한 상관관계가 있는지 확인하였다. 실험 결과, 한국형 DBQ를 통하여 도출되는 난폭운전성향이 높은 사람들이 상대적으로 빠른 주행속도와 가속도 행태를 보이는 것을 확인할 수 있었다. 이를 통하여 상대적으로 위험운전행동을 보이는 운전자를 추정할 수 있는 평가 방법을 확인할 수 있었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권6호
• /
• pp.269-273
• /
• 2005

In order to achieve high efficiency and low cost, new high-speed addressing method is suggested. This can be implemented by reducing the address discharge time lag through the priming effect. This paper suggests a new ADR(Address During Reset) driving method which provides priming particles by a separated driving method without adding auxiliary electrode or auxiliary discharge. The experimental results show an approximately 100ns reduction in the formative delay time of address discharge and a reduction in jitter of over 200ns. Also, due to enough time being available for reset, there was a reduction of about 29$\%$ in linht emitted during the reset period considerably.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권3호
• /
• pp.207-212
• /
• 2017

Purpose: This article provides an efficient cushion molding method for improving reliability of the rotation driving system. Method: Allowable stress level for cushion is calculated by using physical characteristics of the rotation driving system. In addition, various test units are manufactured and used to conduct the rebound resilience, the burst pressure and the alternating load test. Results: Actual allowable stress level and test results of the rebound resilience, the burst pressure and the alternating load test are provided. Conclusion: The cushion manufactured by the compression molding method gives more preferable characteristics for improving the reliability of the rotation driving system.

• 자동차안전학회지
• /
• 제13권4호
• /
• pp.123-128
• /
• 2021

This paper present box feature estimation from LiDAR point cluster using maximum likelihood Method. Previous LiDAR tracking method for autonomous driving shows high accuracy about velocity and heading of point cluster. However, Assuming the average position of a point cluster as the vehicle position has a lower accuracy than ground truth. Therefore, the box feature estimation algorithm to improve position accuracy of autonomous driving perception consists of two procedures. Firstly, proposed algorithm calculates vehicle candidate position based on relative position of point cluster. Secondly, to reflect the features of the point cluster in estimation, the likelihood of the particle scattered around the candidate position is used. The proposed estimation method has been implemented in robot operating system (ROS) environment, and investigated via simulation and actual vehicle test. The test result show that proposed cluster position estimation enhances perception and path planning performance in autonomous driving.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.148-150
• /
• 2008

In this paper, we report the improved driving methode using planar-gate for field emission light source. Due to the cold cathode in field emission device, it has advantage for driving system in terms of high speed pulse driving with narrow duty ratio. This paper shows that our driving method offers the stable and reliable driving system without rapid electric field variation for field emission light source.

• 전자공학회논문지A
• /
• 제31A권7호
• /
• pp.110-116
• /
• 1994

In this paper a Duty Effective Overlap Scanning method (DEOS) for the improvement of driving efficiency of LC displays which have the RMS voltage responding characteristics is proposed and new processing method of data signals for optimum application of this method is also proposed. Proposed method has a few advantages such as the increment of duty ratio the increment of driving power loaded on LC cell and the decrement of RMS voltage error rate caused by signal attenuation on electrodes composing of display when compared with the conventional method which is called as optimum voltage amplitude selection method. And also by adopting new data signal processing method which has 3 kinds of voltage levels additional advantage much improving crosstalk phenomenon which is the most serious problems of simple matrix structured display is obtained. For the characteristic estimation new mathematical representation for new overlap scanning method and data signal processing method are induced and defined. And by the defined formula and simulation the characteristics of the proposed method and the conventional method are compared and analyzed. As a result of estimation this new method being able to optimize the overlap rate of scan signal and using 3 levels of data signals has the characteristic which can improve the driving efficiency of LC displays.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.11-17
• /
• 1983

Stress distribution under a driving lugged wheel was obtained by photoelastic method. The distribution showed two distinct parts, one part is due to sinkage and other due to compression. Results of the study are summarized as follows. 1. The tangential reactions of sinkage as well as compressing parts were directly proportional to tangential load to the driving wheel, that's appeared to be thrust of the driving wheel. The normal reactions of both sinkage and compressing parts were directly proportional to the vertical load to the driving wheel, that's appeared to be resistance against wheel motion. 2. When the tangential load was constant, changing the vertical load did not show any significant thrust variation of the driving wheel. 3. Under the condition of this experiment, the ratio of vertical load to tangential load (T.L/V.L) must be greater than 1.0 in order for the wheel to roll.

• 대한인간공학회지
• /
• 제19권2호
• /
• pp.1-14
• /
• 2000

Driving simulators have been developed for evaluating users' reaction to various driving situations. Dynamic simulators have, however, limitations of the motion feedback in space. Therefore, this paper presents a driving simulator and suggests a human sensibility ergonomics (kansei engineering) method to be used in improving sense of motion through a vehicle simulator. Human sensibility ergonomics(kansei engineering) is defined as translating technology of the customer' feeling about a new product into design elements. Constituents of the simulator were defined and the virtual world was generated by the object modeling technique. Senses perceived were classified into feelings of velocity, acceleration, rotation, and vibration based on the human sensibility associated with driving. And the most frequent verbal expressions were collected from 17 male subjects to define complex human sensibility.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.703-707
• /
• 2000

This paper studied on the lateral motion of the gantry crane which is used for the automated container terminal. Though several problems are occurred in driving of gantry crane, they are solved by the motion by the operator. But, if the gantry crane is unmanned, it is automatically controlled without any human operation. Especially, the collision between wheel-flange and rail is a very critical problem in driving of unmanned gantry crane. To bring a solution to these problems, the lateral and yaw dynamic equations of the driving mechanism of gantry crane are derived. And this study used PD(Proportional-Derivative) Controller to control the lateral displacement and the yaw angle. The simulation result of the driving mechanism using the Runge-Kutta method is presented in this paper.