• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2747-2752
• /
• 2003

This paper has develops a new framework to understand the human’s driving maneuver based on the expression as HDS focusing on the driver’s stopping maneuver. The driving data has been collected by using the three-dimensional driving simulator based on CAVE, which provides three-dimensional visual information. In our modeling, the relationship between the measured information such as distance to the stop line, its first and second derivatives and the braking amount has been expressed by the PWPS model, which is a class of HDS. The key idea to solve the identification problem was to formulate the problem as the MILP with replacing the switching conditions by binary variables. From the obtained results, it is found that the driver appropriately switches the ‘control law’ according to the following scenario: At the beginning of the stopping behavior (just after finding the stopping point), the driver decelerate the vehicle based on the acceleration information, and then switch to the control law based on the distance to the stop line.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.234-240
• /
• 2003

This study aims to investigate dynamic properties of express buses in the very low frequencies which affect motion sickness incidence. Since passengers often use express buses for long distance traveling, it is a critical point whether a give rise to motion sickness or not. In the study accelerations at the three points on the floor of the six test vehicles were measured during the driving at constant speeds. By applying frequency weighting curves suggested in ISO 2631-1 and ISO 2631-3, physical amount of accelerations were changed into perceptual amount which determines incidence of motion sickness. Motion sickness dose values were calculated from the frequency weighted time history of accelerations, and compared between the vehicles, driving conditions, and the seat positions in the bus. During the driving on public road and high ways for 50 minutes vomiting incidence ratios ranged 0.4 to 0.8%, which were equivalent to 2.4 to 4.8% for 5 hours' driving. The value of 4.8 % means two among 45 passengers may vomit after the traveling, which is very serious situation. Considering the very smooth driving condition at which the data were collected, motion sickness dose values will increase in real situations

• 한국도로학회논문집
• /
• 제11권1호
• /
• pp.37-45
• /
• 2009

도로의 터널출구에서 인터체인지 분기점 구간은 도로이용자가 본선을 주행하다가 인근 목적지로 나가기 위하여 터널을 벗어나서 전방에 설치된 표지상의 목적지 지명을 확인하고, 차로를 변경해서 인터체인지 연결로로 들어가는 단계를 갖는다. 따라서 이 구간에서는 도로이용자의 다양한 행동이 요구되므로 도로이용자의 인간공학적 요소를 중시한 도로설계가 되어야 하는 구간이다. 본 연구는 도로이용자의 인간공학 요소를 고려하여 터널출구와 인터체인지 분기점구간의 최소이격거리를 제공하고자 하였다. 연구수행을 위해서 도로주행 시뮬레이터를 이용하여 다양한 연령층(20대${\sim}$70대)이 실험에 참여하여 터널과 인터체인지 분기점 산정에 대한 통계적 검증을 수행하였다. 그 결과 터널출구에서 인터체인지 변이구간(감속차로 시점)의 시점까지는 최소 500m 이상의 거리가 확보되어야 하는 것으로 나타났다. 본 연구는 과학적인 근거를 통해서 터널과 인터체인지 분기점간의 최소이격거리 정립에 대한 기초연구 수행이 이루어졌다는 점에서 논문의 의의가 있다. 향후 이용자에게 보다 안전한 지침을 제공하여 도로주행의 안전성을 도모할 수 있는 기반을 제공할 것으로 기대할 수 있다.

• 한국가스학회지
• /
• 제15권3호
• /
• pp.58-66
• /
• 2011

본 연구에서는 건설 현장에 매설된 삼중관이 항타 진동에 노출되었을 경우에 발생하는 동적 거동을 분석하였다. 항타 에너지는 7tonf의 램이 1.2m에서 낙하하였을 경우로 선정하였으며 이격 거리는 5∼30m로 변화하여 연구를 진행 하였다. 관의 길이 방향 중심에서의 진동 속도와 응력을 확인 하였고, 감쇠비를 고려하여 삼중관의 거동을 분석하였다. 매설 심도가 동일한 경우의 진동 속도에 대한 감쇠율은 이격 거리가 증가함에 따라 감소하는 추세를 보이며 내관에서 역시 이격 거리가 증가함에 따라 감소하는 추세를 보인다. 상하부에서 최대 응력값을 보이는 내관과 달리 외관은 불규칙한 응력 분포를 나타내는 것을 확인하였다.

• 동력기계공학회지
• /
• 제21권4호
• /
• pp.57-61
• /
• 2017

The vehicle label fuel economy is used as an energy management indicator nationwide. It induces technology development of automobile manufacturers and plays a role of providing information when purchasing a consumer vehicle. However, consumers who purchase a new vehicle continued to complain that the label fuel economy is different from the mandatory fuel economy rate. The domestic fuel economy measurement method is the same as the North American measurement method. The results of the two test modes (urban (FTP-75 mode), highway (HWFET mode)) are calculated in five test modes reflecting various environmental conditions and driving patterns 5-cycle correction formula is used which is equivalent to the fuel efficiency value. In this study, to solve the consumers' curiosity about the fuel economy of new vehicle, we use domestic fuel economy measurement method to measure the new car condition within 150 km of driving distance and the cumulative driving distance condition of domestic label fuel economy test vehicle. A comparative evaluation of fuel economy was carried out for a durability vehicle of $6,500{\pm}1,000km$. A result, mean value of the fuel economy of the four gasoline vehicles increased by 2.7 % in the city center mode and by 2.5 % in the highway mode in the durable vehicle compared new vehicle. And in the case of the diesel vehicle it increased by 2.5 % and 3.9 % respectively. The harmful exhaust gas emitted from the vehicle also resulted in more emissions of both gasoline and diesel vehicles in new vehicles. It is considered that the increase of the frictional force of the vehicle driving system and the lubricating oil system would have an effect on the reduction of the fuel economy of the new vehicle, and it was found that the fuel economy and the exhaust gas were improved by proper cumulative distance (domesticate) to the new vehicle.

• 한국소음진동공학회논문집
• /
• 제16권7호
• /
• pp.697-703
• /
• 2006

This article proposes a new technique for the reduction of vibration and noise in the geared system by adjusting the distance between gear shafts. The vibration and noise may be produced by the abnormal force applied to the tooth face. And the force may be the cause of ununiform velocity in the driven shaft. If the velocity is obtained to be uniform by adjusting the distance between shafts. the vibration and noise may be reduced to some extent. In order to review, a dynamic analysis model for the gear train used in a mill turret and a test rig are developed. The velocities in the driven shaft are calculated by dynamic simulations for the model and noises in the test rig are measured with varying of the distance between shafts. The comparison of simulation and test data shows that the distance between shafts at the most uniform velocity has the lowest level of noise.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.115-121
• /
• 2001

A driving load estimation method for intelligent cruise control(ICC) vehicles has been proposed in this paper. Vehicle driving load is one of the most important factors of perturbations in vehicle control and can affect the control performance critically. The effect of the control with driving load estimation on vehicle-to-vehicle distance control has been presented and investigated via computer simulations and vehicle tests. The results show that vehicle-driving-load-adaptive control can provide an ICC system with a good acceleration tracking performance. In addition, the results show that driving load estimation can compensate not only the variation of driving load but also the modeling errors.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.653-658
• /
• 2000

A driving load estimation method for intelligent cruise control(ICC) vehicles has been proposed in this paper. The driving load is one of the most important factors of perturbations in vehicle control and can affect the control performance critically. The Effect of the control with driving load estimation on vehicle-to-vehicle distance control has been presented and investigated via computer simulations and vehicle tests. The results show that the control with driving load estimation can provide ICC system with a good acceleration tracking performance. In addition, the results show that driving load estimation can compensate not only variation of driving load but also the modeling errors.

• 한국자동차공학회논문집
• /
• 제9권3호
• /
• pp.121-130
• /
• 2001

This paper addresses a method for evaluating perceived velocities of the graphic module in a driving simulator. The major two graphic factors associated with perceived velocities are analyzed: they are the lateral distance between a virtual driver and an array of environmental objects and the textural density of these objects. A graphical representation of a vehicle and its surrounding environment are constructed by employing a three-dimensional tool, Pro/ENGINEER and a virtual environment, dVISE. Using the developed virtual driving environment, experiments have been carried out to formulate the relationship between velocity perception and each factor. Based on the experimental results, nonlinear regression equations are derived to show how the perceived velocities are dependent upon distance/density.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권1호
• /
• pp.51-56
• /
• 2013

With the active development of hybrid electric vehicle (HEV), the application of interior permanent magnet synchronous motor (IPMSM) has been expanded. As wide driving region of IPMSM for electric vehicle (EV) traction motor is required, many studies are conducted to improve characteristics of a motor in both low and high-speed driving regions. A motor in high-speed driving region generates (produces) large stress to the rotor. Thus, the rotor needs to be designed considering the mechanical safety. Therefore, in this paper, we conducted stress analysis and electromagnetic analysis to determine the centerpost's distance which is considered important during the design of IPMSM for EV traction motor in order to secure mechanical safety and satisfy specifications of output requirement.