• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.925-930
• /
• 2004

This paper is to study vibration effects of the dynamic vibration absorber. Multi-body dynamic analysis is carried out for the vehicle driveline model using ADAMS with flexible propeller shaft attached with the vibration damper. Primary bending mode frequency of the propeller shaft is obtained from the simulation and coincides with the experimental result. Various design parameters are studied in dynamic simulation operated by the engine torque input. This paper identifies the responses of dynamic vibration absorbers in the driveline with propeller shaft, which will be used to find out optimal design parameters.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 the technical trends in the world automobile and lubricant market
• /
• pp.21-24
• /
• 2002

There is a trend with driveline lubricants toward improved thermal stability, vehicle component durability and fuel efficiency. These improvements can significantly reduce vehicle operating costs and improve customer satisfaction. Of these improvements, the fuel efficiency is getting a substantial attention due to recent focus on $CO_2$ emission control in Europe, Japan and $CAF{\'{E}}$ requirement in U.S.A. Lower viscosity axle oils and transmission fluids are currently being evaluated as potential solutions since these lubricants tend to reduce the churning losses and can improve the fuel efficiency. However, these lubricants should provide adequate gear and bearing protection, while increasing the overall efficiency of the driveline components. In this paper, the development of new fuel efficient axle was discussed with the focus on the effect of base oils, additives, and viscosity modifiers on the fuel efficiency of driveline components.

• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.96-102
• /
• 1997

Eigenvalue analysis of vibration mode and an analysis by frequency response among the methods of predicting gear noise are related with transmitting sound of vibration. In this study we intended to reduce the vibration noise of differential gear by reducing torque fluctuation of drive pinion shaft which causes vibration noise of differential gear in rear wheel drive vehicles. For this we developed multi-degree of freedom analysis model in which mass moment of inertia and torsional spring combined and we examined the influence of torsional vibration of driveline elements by performing forced vibration analysis of engine excitation torque. We studied the methods for reducing torsional vibration of driveline according to the design factor of propeller shaft and examined the effects reducing vibration in differential gear by applying flexible coupling.

• Journal of Biosystems Engineering
• /
• 제27권5호
• /
• pp.371-380
• /
• 2002

The objectives of this study were to analyze gear rattle in a power drive line using its dynamic model and to derive design guidelines to eliminate it. A 72 degrees of freedom model of power driveline of an agricultural tractor was developed and proved to be valid fer predicting the collision characteristics of gears in mesh, which may determine whether or not the gear rattle will occur. Using the model the effects on the rattle of drag torque, backlash, mass moment of inertia, transmitting torque were analyzed. Increasing drag torque or decreasing mass moment of inertia reduced gear rattle. The gears transmitting power do not develop rattles. It was also found that a large amount of rattle is likely to be developed by the change gears placed at the end of idle shafts. Increasing the drag torque to such change gears may be the most effective way of reducing the gear rattle in a tractor driveline.

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.14-19
• /
• 2016

Transmission error (TE) is the most important cause of gear noise and vibration because TEs affect the changes of the force and the speed of gears. TE is usually expressed as an angular deviation, or a linear deviation measured at the pitch point and calculated at successive positions of the pinion as it goes through the meshing cycle. Accurate measurement of TE for gear transmission will provide a reasonable basis for gear design, manufacturing processes and quality control. Therefore, in order to study the accuracy of the gear transmission, stability, TE, vibration and noise after gear micro-geometry modification, a gear transmission test rig is proposed in this paper, which is based on the existing technical conditions, by using reasonable testing methods, hardware and a signal processing method. All of the details and the experience can be taken into consideration in the next upgraded test rig.

• 한국자동차공학회논문집
• /
• 제3권4호
• /
• pp.19-29
• /
• 1995

This paper discusses the stick-slip phenomenon of the driveline system of a vehicle in consideration of friction. Friction is operated on the between of flywheel and clutch disk. The expressions for obtaining the results have been derived from the equation of motion of a three degree of freedom frictional torsion vibration system which is made up driving part(engine, flywheel), driven part(clutch, transmission) and dynamic load part(vehicle body) by applying forth-order Rungekutta method. It was found that the great affect parameters of the stick-slip or stick motion were surface pressure force between flywheel and clutch disk, time decay parameter of surface pressure force and 1st torsional spring constant of clutch disk when driveline system had been affected by friction force. The results of this study can be used as basic design data of the clutch system for the ride quality improvement of a car.

• 한국정밀공학회지
• /
• 제33권2호
• /
• pp.109-114
• /
• 2016

Nowadays, lower gear vibration and noise are necessary for drivers in automotive gearbox, which means that transmission gearbox should be optimized to avoid noise annoyance and fatigue before quantity production. Transmission error (T.E.) is the excitation factor that affects the noise level known as gear whine, and is also the dominant source of noise in the gear transmission system. In this paper, the research background, the definition of T.E. and gear micro-modification were firstly presented, and then different transmission errors of loaded torques for the spur gear pair were studied and compared by a commercial software. It was determined that the optimum gear micro-modification could be applied to optimize the transmission error of the loaded gear pair. In the future, a transmission test rig which is introduced in this paper is about to be used to study the T.E. after gear micro-geometry modification. And finally, the optimized modification can be verified by B&K testing equipment in the semi-anechoic room later.

• International Journal of Automotive Technology
• /
• 제7권5호
• /
• pp.535-545
• /
• 2006

A nonlinear analysis of torsional self-excited vibration in the driveline system for wheeled towing tractors was presented, with a 2-DOF mathematical model. The vibration system was described as a second-order ordinary differential equation. An analytical approach was proposed to the solution of the second-order ODE. The mathematical neighborhood concept was used to construct the interior boundary and the exterior boundary. The ODE was proved to have a limit cycle by using $Poincar\'{e}-Bendixson$ Annulus Theorem when two inequalities were satisfied. Because the two inequalities are easily satisfied, the self-excited vibration is inevitable and even the initial slip rate is little. However, the amplitude will be almost zero when the third inequality is satisfied. Only in a few working modes of the towing tractor the third inequality is not satisfied. It is shown by experiments that the torsional self-excited vibration in the driveline of the vehicle is obvious.

• Journal of Biosystems Engineering
• /
• 제28권6호
• /
• pp.537-544
• /
• 2003

The objectives of this study were to investigate the failure characteristics of a total of 90 parts of tractor driveline, and to predict their average annual demands required to perform the after-sales service. The failure characteristics such as failure mode, mean time between failures, characteristic life and reliability were analyzed using the data collected through the experienced mechanics at the part centers of the tractor manufacturers. The analysis was based on the assumption that the failure distribution follows the Weibull distribution. The average annual demands were also predicted for the replacement parts using the mean time between failures and the renewal theory based on the Weibull distribution. The results of the study revealed that the driveline parts failure was mostly from wearout and their average characteristic life is about 1.760 hours. The estimated mean time between failures was in a range of 670∼3,740 hours and reliability in a range of 40∼60％. The annual replacement demands were in a range of 4∼45 for a service of 100 tractors.

• 한국산학기술학회논문지
• /
• 제7권6호
• /
• pp.1021-1027
• /
• 2006

엔진의 토크 변동과 추진축의 각속도 변화는 차량 동력 전달계의 주요 가진원이다. 본 논문에는 이들 가진원의 발생 기구에 대하여 논하였다. 이 시스템의 등가모델은 가진원과 유사하게 구성되었고, ARLA Simul v 6.7과 ARLA-Simstat v 2.3을 이용하여 컴퓨터 시뮬레이션을 수행하였다. 컴퓨터 시뮬레이션의 결과는 동력 전달계의 비틀림 가진원의 특성을 보였다. 엔진과 추진축 시스템에 대한 실험 장치는 차량의 부품으로 구성되었다. 플라이휠의 토크 변동과 추진축의 각속도는 실험 장치로 부터 측정하였다. 실험결과는 시뮬레이션 결과와 비교하였고, 이론적 결과와 일치하였다.