• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.101-116
• /
• 2002

Modern vehicles require a high degree of refinement, including good driveability to meet customer demands. Vehicle driveability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. Therefore, Engine and drive train characteristics should be considered to achieve a well balanced vehicle response simultaneously. This paper describes analysis procedures using a mathematical model which has been developed to simulate spark timing control logic. Inertia mass moment, stiffness and damping coefficient of engine and drive train were simulated to analyze the effect of parameters which were related vehicle dynamic behavior. Inertia mass moment of engine and stiffness of drive line were shown key factors for the shuffle characteristics. It was found that torque increase rate, torque reduction rate and torque recovery timing and rate influenced the shuffle characteristics at the tip-in condition for the given system in this study.

• Journal of Drive and Control
• /
• v.17 no.2
• /
• pp.19-27
• /
• 2020

The purpose of this study was to suggest design criteria for the HMT (hydro-mechanical transmission) of a 55 kW-class agricultural tractor, develop a simulation model, and evaluate its performance such as axle rotational speed, tractor speed, and power transmission efficiency. In this study, the HMT comprised a compound planetary gear and a HSU (hydro-static unit), and the compound planetary gear comprised two planetary gear sets. The HMT has three gear stages, and the maximum tractor speed was selected as 40 km/h. The simulation time was set at 2736 hours considering the lifetime of the tractor, and the simulation was performed for each gear stage at the engine-rated power conditions. As a result of the simulation, the axle rotational speeds for each gear stage were 39, 77, and 158 rpm, respectively. The range of tractor speed for each gear stage were 1.05-10.22 km/h, 10.74-20.17 km/h, and 20.70-41.40 km/h, respectively. The APE (absolute percentage gear) for the tractor's maximum speed between target value and simulation results were 2.20%, 0.85%, and 3.50%, respectively. Also, the power transmission efficiency for each gear stage were 0-75%, 72-81%, and 69-81%, respectively. The simulation results for the power transmission efficiency of the HMT were similar with the results of the previous research. This was a basic study on the development of the HMT for an agricultural tractor. In future studies, it is necessary to develop a tractor platform and evaluate the performance. The comparison between the simulation model and the HMT tractor should be performed.

• Korean Journal of Agricultural Science
• /
• v.51 no.2
• /
• pp.133-146
• /
• 2024

Selection of gear reduction ratio is essential for machine design to ensure suitable power and speed during agricultural operations. The goal of the study was to evaluate the gear reduction ratio for a 1.6 kW four-wheel-drive (4WD) multi-purpose agricultural electric vehicle platform using workload data under different off-road conditions. A data acquisition system was fabricated to collect workload (torque) of the vehicle acting on the gear shaft. Field tests were performed under three driving surfaces (asphalt, concrete, and grassland), payload operations (981, 2,942, and 4,903 N), and slope conditions (0 - 4°, 4 - 8°, and 8 - 12°), respectively. Commercial speed reduction gear phases were attached to the input shaft of the vehicle powertrain. The maximum required torque was recorded as 37.5 Nm at a 4,903 N load with 8 - 12° slope levels, and the minimum torque was 12.32 Nm at 0 - 4° slope levels with a 981 Nm load for a 4 km/h speed on asphalt, concrete, and grassland roads. Based on the operating load condition and motor torque and rotational speed (TN) curve, the minimum and maximum gear reduction ratios were chosen as 1 : 50 and 1 : 64, respectively. The selected motor satisfied power requirements by meeting all working torque criteria with the gear reduction ratios. The chosen motor with a gear reduction ratio of 1 : 50 was suitable to fit with the motor T-N curve, and produced the maximum speeds and loads needed for driving and off-road activities. The findings of the study would assist in choosing a suitable gear reduction ratio for electric vehicle multi-purpose field operations.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.11a
• /
• pp.78-85
• /
• 1989

Conventional theory of gear mechanism can not be applied to analyze the harmonic drive due to specific movement of the tooth. Therefore, external tooth profile can't be manufactured by conventional exclusive tools which have pressure angle of 20$\circ$C. This paper deals with an analysis of kinematics and strength analysis of tooth. Then a theoretical new tooth profile of the flexspline and method of manufacture of external tooth profile are presented.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.153-158
• /
• 2017

Reducer is a device to transmit and change torque and speed from drive shaft to driven shaft with excellent transmission efficiency, and it is widely used in many areas today. Reduction gear consists of two axes, gear, bearing supporting axes, and housing. The simplest method to transmit rotation or power to multiple axes is to attach circular plates to two axes and contact each other. However, in this case, if increasing number of rotations or if contact pressure is small, because of slipping, it cannot transmit power. For problems for the current reducer case, it is heavy and its assembling and repair is difficult. In addition, there are few studies about manufacturing and performance testing of worm gear reducer, causing lack of the foundation to improve the product competition and the performance.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.4
• /
• pp.245-252
• /
• 2016

Girth gears are applied in the mining, cement, and mineral processing industries and used in various types of horizontal mills, rotary dryers and kilns, and other heavy-gear ring applications. The large ring gears are normally fitted outside mills or kilns to provide the primary rotational drive. Recently, an external pinwheel gear set (e-PGS) was introduced to overcome manufacturing problems associated with girth gears. e-PGS is also suitable for low-speed, heavy-duty mechanical transmission and dusty and poor-lubrication conditions. This paper first presents a new profile modification of root relief for the e-PGS cam pinion. We then investigate load-stress factors to estimate the surface fatigue life by varying the shape design parameters. The results show that the contact fatigue life of an e-PGS can be extended significantly by increasing the profile shift coefficient. However, support bearing life of the pinwheel depends more on the contact force distribution than the profile shift coefficient.

• Journal of Drive and Control
• /
• v.16 no.2
• /
• pp.15-21
• /
• 2019

In this study, the maximum system efficiency of the electro-hydrostatic actuators was experimentally investigated, where small size external gear pumps with volumetric displacement under 1.3 cc/rev were combined with a 400W servomotor as the prime mover. Since the efficiency data of the servomotor, gear pumps and hydraulic cylinder were not provided by the suppliers, experimental apparatuses for their efficiency measurement were extra built up. When a gear pump with a volumetric displacement of 1.27cc/rev was used on an electro-hydrostatic actuator system, the maximum system efficiency was not higher than 70%. This was because the most effective operation ranges of the motor and pump did not coincide each other. In order to match their operation ranges as one of the most crucial design factors, a speed reduction mechanism can be used, such as a timing belt. It was shown in the study that the maximum system efficiency could be increased from 70% to 76% in that way.

• Journal of Drive and Control
• /
• v.19 no.4
• /
• pp.1-9
• /
• 2022

The structure and operating principle of the 2-speed shift reducer were explained, the allowable bending stress value of the material was compared with the analysis result through FM structural analysis program, and the average stress distribution value of von Mises was performed on the gear root atmosphere. The structural safety of the 2-speed planetary gear reducer was verified through FM structural analysis. The natural frequency was calculated by applying the specifications of the planetary gears of the 2-speed gearbox, and the critical speed of resonance was calculated by calculating the natural frequency and the transmission error of the engaged gear pair. As a result of analyzing the critical speed, since it is formed higher than the actual operating speed range, it is considered safe because there is no resonance problem due to the suggested specifications of the planetary gears of the 2-speed shift reduction.

• Journal of Drive and Control
• /
• v.17 no.4
• /
• pp.125-132
• /
• 2020

The objective of this study was to analyze the axle load of a rice transplanter when planting rice seedlings at different working load conditions to select a suitable gear stage and a constant planting depth for rice seedlings. In this study, there are four levels of planting distances (26, 35, 43, and 80 cm) and three planting depths (low, medium, and high) with two gear stages (1.3 and 1.7 m/s). Axle loads and required planting pressures were analyzed statistically. It was observed that axle torques were increased with increasing planting depths for both gear stages, meaning that axle torques were directly proportional to planting depths for both gear stages. It was also observed that required planting pressures had a significant difference between planting distances. Planting pressures also showed significant difference according to gear stage and planting depth. These results indicate that planting pressures were directly proportional to both gear stage and planting depth. Results revealed that the automatic depth control system of a rice transplanter could not guarantee a constant planting depth as supplied pressures were variable. This indicates that a control algorithm is needed to ensure a constant planting depth. In the future, a control algorithm will be developed for an automatic depth control system of a rice transplanter to improve its comprehensive performance and efficiency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.822-827
• /
• 2002

In general, jerk phenomenon appeared because of gear changing, when a vehicle starts off or climbs an incline. Therefore, it makes ride quality worse. In this paper, an optimal pattern of automatic transmission was designed using fuzzy logic in order to improve ride quality. After del eloping fuzzy rule for shift pattern control of automatic transmission, dynamic characteristics (i.e. acceleration, velocity, distance and so on) were simulated using dynamic model of a car. To do this he powertrain model of a vehicle with automatic transmission including torque converter, gear box, and final gear drive - from engine to tire - is developed.