• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.1
• /
• pp.1-4
• /
• 2008

The growth of composite-structured Nd:$GdVO_4$ single crystal rods by the double die EFG method is reported. Two crucibles are combined with an outer and inner die for ascending of different melt. The composite-structured Nd:$GdVO_4$ single crystal rods with a length of 50 mm and an outer diameter of 5 mm including of inner Nd-doped core region with diameter 3 mm were grown successfully. Nd distribution in the, radial direction has graded profile from result of EPMA. Absorption coefficient in the core region at 808 nm was $42cm^{-1}$. Finally, we demonstrated the laser oscillation using our composite crystal and 2-W output was obtained.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.12-16
• /
• 2004

We show that the extinction ratio is improved using slight asymmetry in two core refractive indices of polarization independent very short vertical directional couplers with the double-sided deep-ridge (DSDR) waveguide structure. The optimum asymmetry with the maximum extinction ratio and the tolerance of the refractive index of core with the extinction ratio larger 1ha]1 30 ㏈ increase as the thickness of inner cladding layer and the two cores decrease due to the increase of the coupling strength between the two cores. Also, the device length and the tolerance of the device length with the extinction ratio larger than 30 ㏈ decrease as the thickness of the inner cladding layer and the two cores decrease due to the increase of the coupling strength between the two cores. We show that polarization independent vertical directional couplers with the DSDR waveguide structure with the device length less than 100 ${\mu}{\textrm}{m}$ and the extinction ratio larger than 30 ㏈ could be implemented.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.1
• /
• pp.23-26
• /
• 2003

This paper presents conceptual design and 3-D electromagnetic analysis of IMVA transformer with BSCCO-2223 High Tc Superconducting (HTS) tapes. The rated voltages of each sides of the transformer are 22.9 kV and 6.6 kV, and double pancake windings were adopted. High voltage and Low voltage sides were composed of several double pancake windings. Four HTS tapes were wound in parallel for the windings of low voltage side and were transposed in order to distribute the currents equally in each conductor The transformer core was designed as a shell type core made of laminated silicon steel plates and the core is separated with the windings by a cryostat with Fiberglass Reinforced Plastics(FRP). A sub-cooling system using L$N_2$ were designed to maintain the coolant temperature 65K. Finally perpendicular components of magnetic field applied to tapes were calculated 0.247 in the rated operation using 3-D analysis. A real 1MVA HTS transformer will be manufactured in near future based on the design parameters presented in this paper.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.05a
• /
• pp.90-91
• /
• 2000

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.4B no.2
• /
• pp.54-58
• /
• 2004

This paper presents the iron core design method of a high temperature superconducting (HTS) transformer considering voltages per turn (V/T). In this research, solenoid type HTS coils were selected for low voltage (LV) winding and double pancake coils for high voltage (HV) winding, just as in conventional large power transformers. V/T is one of the most fundamental elements used in designing transformers, as it decides the core cross sectional area and the number of primary and secondary winding turns. By controlling the V/T, the core dimension and core loss can be changed diversely. The leakage flux is another serious consideration in core design. The magnetic field perpendicular to the HTS wire causes its critical current to fall rapidly as the magnitude of the field increases slowly. Therefore in the design of iron core as well as superconducting windings, contemplation of leakage flux should be preceded. In this paper, the relationship between the V/T and core loss was observed and also, through computational calculations, the leakage magnetic fields perpendicular to the windings were found and their critical current decrement effects were considered in relation to the core design. The ％ impedance was calculated by way of the numerical method. Finally, various models were suggested.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.17-20
• /
• 2005

This paper reported the temperature history of concrete placed at deck plate slab under cold climate condition by varying with surface insulating type. No curing sheet and simple insulation curing including non-woven fabric, double layer bubble sheet, the combination of double layer bubble sheet and non-woven fabric dropped temperature below zero within 24 hours, which caused frost damage at early age. On the other hand, the combination of double layer bubble sheet and non-woven fabric and double layer bubble sheet and styrofoam maintained minimum temperature above $4^{\circ}C\;and\;8^{\circ}C$, respectively. Based on core test results compressive strength of concrete with the combination of double layer bubble sheet and non-woven fabric and double layer bubble sheet and styrofoam was higher than those with other curing method due to good insulation effect.

• Design & Manufacturing
• /
• v.1 no.1
• /
• pp.1-5
• /
• 2007

Double injection molding process is very efficient molding-method for molding the products which is consist of multi-materials. Fuel-tube holder which is necessary for automobil power train and circulation systems is composed of plastic and rubber materials to minimize the vibration and pulsation noises. In existing process, fuel-tube holder was made by the insert molding process or assembly process after molding. If fuel-tube holder is manufactured by double injection molding process, it may be realize to improve the product quality, efficiency of molding-process and retrenchment of manufacturing cost. In this study, for manufacturing fuel-tube holder by double injection molding process, the analysis of joining characteristics between PA6(polyamide 6) and TPE(thermoplastic elastomer) was executed and the double injectin mold for molding fuel-tube holder with core toggle mechanism was fabricated. Finally, fuel-tube holder was molding using fabricated double injection mold.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.634-642
• /
• 1998

This paper deals with the analytical model of an elastic porous material in sound transmission loss of a double panel with fiber glasses. From the parametric analysis, it is concluded that the boundary condition, which is concerned to the contact between the skin panel and core materials, does not have much influence on sound transmission loss of a double panel with fiber glasses, and material properties of the porous material become, however, important factors to mass-spring-mass resonance. The comparisons of the prediction with the measurement of sound transmission loss of walls show good agreement between the two values.

• Progress in Superconductivity and Cryogenics
• /
• v.2 no.2
• /
• pp.37-43
• /
• 2000

This paper describes the construction and test results of a 10kVA single phase HTS transformer. Double pancake windings with BSCCO-2223 HTS tape and G10-FRP cryostat with room temperature bore are used in the transformer. Two double pancake windings are connected in series to provide 188 turns and other two double pancake windings are connected in parallel to conduct the secondary current of 45.4[A]. Coefficients of the constructed transformer are obtained using the fundamental teats of the transformer. According to the test results, larger leakage reactance than expected is observed due to the bulky core which surrounds the sryostat.

• Steel and Composite Structures
• /
• v.22 no.5
• /
• pp.1141-1162
• /
• 2016

Concrete-filled double skin steel tube (CFDST) beam-columns are widely used in industrial plants, subways, high-rise buildings and arch bridges. The CFDST columns have the same advantages as traditional CFT members. Moreover, they have lighter weight, higher bending stiffness, better cyclic performance, and have higher fire resistance capacities than their CFT counterparts. The scope of this study is to develop finite element models that can predict accepted capacities of double skin concrete-filled tube columns under the combined effect of axial and bending actions. The analysis results were studied to determine the distribution of stresses among the different components and the effect of the concrete core on the outer and inner steel tube. The developed models are first verified against the available experimental data. Accordingly, an extensive parametric study was performed considering different key factors including load eccentricity, slenderness ratio, concrete compressive strength, and steel tube yield strength. The results of the performed parametric study are intended to supplement the experimental research and examine the accuracy of the available design formulas.