• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.745-752
• /
• 2012

This paper studies the effect of the compressive strength for combined alkali-activated slag mortars. The effect of activators such as alkali type and dosage factor on the strength was investigated. The alkalis combinations made using five caustic alkalis (sodium hydroxide (NaOH, A series), calcium hydroxide ($Ca(OH)_2$, B series), magnesium hydroxide ($Mg(OH)_2$, C series), aluminum hydroxide ($Al(OH)_3$, D series), and potassium hydroxide (KOH, E series)) with sodium carbonate ($Na_2CO_3$) were evaluated. The mixtures were combined in different dosage at 1M, 2M, and 3M. The study results showed that the compressive strength of combined alkali-activated slag mortars tended to increase with increasing sodium carbonate. The strength of combined alkali-activated slag mortars was better than that of control cases (without sodium carbonate). The result from scanning electron microscopy (SEM) analysis confirmed that there were reaction products of calcium silicate hydrate (C-S-H) and alumina-silicate gels from combined alkali-activated slag specimens.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.79-88
• /
• 1993

The purpose of this study is to provide a firm base for the quality improvement of high strength concrete and the development of ultra high strength concrete as well as enviromental con-servation and utilization of byproducts from industrial processing such as Fly ash and Silica fume. A comprehensive experimental study was performed to investigate the effects on the quality improvement of high strength concrete using mineral admixtures. As results, 400~500kg/$\textrm{cm}^2$ compressive strength and excellent flowability can be obtained if fly ash is replaced with cement in the range of 305. In case of using powder type silica fume, 600~700 kg/$\textrm{cm}^2$ compressive strength is showed and 600~800kg/$\textrm{cm}^2$ compressive strength cam be obtained with liquid type silica fume. But it is necessary to increase dosage of high range water reducer for flowability using powder type silica fume. Especially, higher strength concrete cam be obtained when maximum size of coarse aggregate is lower than 25mm.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.232-238
• /
• 1996

In this paper, the properties of high-strength concrete are described with respect to materials and mix conditions(water-cement ratio, chemical admixture, replacement of fly ash). As primary purposes of this study, the optimum mix design method of high-strength concrete to decrease unit cement contents is investigated, and the properties of fresh and hardened concretes are tested in terms of slump, air content and compressive strength. As results of this study, workability and strength development of the high-strength concrete depend on the water-cement ratio, replacement ratio of fly ash and dosage of the chemical admixture. The conditions which are proposed optimum mix design of the high-strength concrete show W/C 37%, S/A 42~45% and unit cement content 470~480kg/$\textrm{m}^3$. Based on the results, the applicability of high-strength concrete in site is clearly proved.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.4
• /
• pp.60-65
• /
• 2015

In order to improve the strength of paper, mixing ratio of Sw-BKP and Hw-BKP and PVA (polyvinyl alcohol) fibers dosage were investigated. When the Sw-BKP fraction was increased, strength properties were increased because of average fibers length increased. When PVA fraction increased, paper strength was increased, but there was dissolution of PVA in water. The reason for improving handsheet strength that contained PVA was due to increased bonding action between the fibers by the PVA. The addition of PVA to kraft pulp would be helpful for packaging paper materials to increase strength and fracture toughness.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.237-242
• /
• 2000

Recently, the importation of overseas cement has been increasing and the spot materials of different quality from Japan have to be treated in overseas construction work for technical cooperation with neighboring countries. However, a study on the quality of those oversea materials has not yet been carried out systematically, especially cement among those materials. Accordingly, in this study the properties of high-strength concrete with oversea cement imported from four countries in East Asia and South-east Asia were investigated under normal and high temperature condition, including the carbonation of normal-strength concrete under normal temperature. As a result, it is found that the required of normal-strength concrete will be expected regardless of temperature condition when the flowability is ensured by selecting the appropriate superplaticizer and dosage of it, and the carbonation rate of normal-strength concrete with overseas cement is approximately the same as that with Japanese one under the condition of the same compressive strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.23-28
• /
• 1998

In this paper, the compensation of the shrinkage in high performance concrete by applying CSA expansive additives are discussed. According to toe experimental results, fluidity and strength decrease with the increase of the dosage of expansive additives. When 5% of expansive additive are mixed, not only high fluidity and strength, but also the compensation of drying-shrinkage can be achieved.

• Resources Recycling
• /
• v.25 no.3
• /
• pp.20-28
• /
• 2016

Assessment on adequate dosage of superplasticizer in eco-friendly ultra-high performance concrete (UHPC) containing industrial by-products was carried out from the standpoint of workability. Various types of industrial by-products, including blast-furnace slag, coal bottom ash and rapid-cooled electric arc furnace oxidizing slag, were utilized, and the effects of dosage of superplasticizer on the workability and strength of UHPC containing the by-products were evaluated. By utilizing the by-products, the workability of UHPC was improved and required dosage of superplasticizer was reduced. In addition, the material cost for UHPC with by-products was decreased due to reduced dosage of superplasticizer.

• Journal of the Korea Concrete Institute
• /
• v.24 no.2
• /
• pp.137-145
• /
• 2012

Strength model for blasted furnace slag mortar blended with sodium was investigated in this study. The main parameters of AAS (alkali activated slag) mortar were dosage of alkali activator, water to binder ratio (W/B), and aggregate to binder ratio (A/B). For evaluating the property related to the dosage of alkali activator, sodium carbonate ($Na_2CO_3$) of 4~8% was added to 4% dosage of sodium hydroxide (NaOH). W/B and A/B was varied 0.45~0.60 and 2.05~2.85, respectively. An alkali quality coefficient combining the amounts of main compositions of source materials and sodium oxide ($Na_2O$) in sodium hydroxide and sodium carbonate is proposed to assess the compressive strength of alkali activated mortars. Test results clearly showed that the compressive strength development of alkali-activated mortars were significantly dependent on the proposed alkali quality coefficient. Compressive strength development of AAS mortars were also estimated using the formula specified in the previous study, which was calibrated using the collected database. Predictions from the simplified equations showed good agreements with the test results.

• Korean Journal of Materials Research
• /
• v.34 no.6
• /
• pp.291-302
• /
• 2024

In this paper, iron ore tailings (IOT) were separated from the tailings field and used to prepare cement stabilized macadam (CSM) with porous basalt aggregate. First, the basic properties of the raw materials were studied. Porous basalt was replaced by IOT at ratios of 0, 20 %, 40 %, 60 %, 80 %, and 100 % as fine aggregate to prepare CSM, and the effects of different cement dosage (4 %, 5 %, 6 %) on CSM performance were also investigated. CSM's durability and mechanical performance with ages of 7 d, 28 d, and 90 d were studied with the unconfined compression strength test, splitting tensile strength test, compressive modulus test and freeze-thaw test, respectively. The changes in Ca²⁺ content in CSM of different ages and different IOT ratios were analyzed by the ethylene diamine tetraacetic acid (EDTA) titration method, and the micro-morphology of CSM with different ages and different IOT replaced ratio were observed by scanning electron microscopy (SEM). It was found that with the same cement dosage, the strengths of the IOT-replaced CSM were weaker than that of the porous basalt aggregate at early stage, and the strength was highest at the replaced ratio of 60 %. With a cement dosage of 4 %, the unconfined compressive strength of CSM without IOT was increased by 6.78 % at ages from 28 d to 90 d, while the splitting tensile strength increased by 7.89 %. However, once the IOT replaced ratio reached 100 %, the values increased by about 76.24 % and 17.78 %, which was better than 0 % IOT. The CSM-IOT performed better than the porous basalt CSM at 90 d age. This means IOT can replace porous basalt fine aggregate as a pavement base.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.628-631
• /
• 2004

In this paper, mechanical properties of concrete incorporating CKD are discussed with W/B and fluidity. For setting properties, an increase in W/B retarded setting time greatly in $5^{\circ}C$, while accelerated in $20^{\circ}C$. For fluidity, an increase in slump delayed the setting time with dosage of SP agent. The presence of CKD has little influence on setting time compared with plain concrete. For compressive strength, an increase in maturity enhanced compressive strength. Fluidity had no relation to compressive strength. At low curing temperature, concrete with CKD has slight strength loss compared with plain concrete. However, remarkable strength loss at low curing temperature in early stage was not found, which can be applicable to low temperature environment concrete placing.