• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.289-294
• /
• 2006

Better fundamental understanding of the interactions between the in-cylinder flows and combustion process is an important requirement for further improvement in the fuel economy and emissions of internal combustion(IC) engines. Flow near a spark plug at the time of ignition plays an important role for early flame kernel development(EFKD). Velocity data measurements in this study were made with a two-component laser Doppler velocimetry(LDV) near a spark plug in a single cylinder optical spark ignition(SI) engine with a heart-shaped combustion chamber. LDV velocity data were collected on an individual cycle basis under wide-open motored conditions with an engine speed of 1,000rpm. This study examines and compares the flow fields as interpreted through ensemble, cyclic and discrete wavelet transformation(DWT) analysis. The energy distributions in the non-stationary engine flows are also investigated over crank angle phase and frequency through continuous wavelet transformation(CWT) for a position near a spark plug. Wavelet analysis is appropriate for analyzing the flow fields in engines because it gives information about the transient events in a time and frequency plane. The results of CWT analysis are provided and compared with the mean flows of DWT first decomposition level for all cycles at a position. Low frequency high energy found with CWT corresponds well with the peak locations of the mean velocity. The high frequency flows caused by the intake jet gradually decay as the piston approaches the bottom dead center(BDC).

• 한국정밀공학회지
• /
• 제15권11호
• /
• pp.58-66
• /
• 1998

A low power consuming laser scanning vibrometer is studied for its development. For its optical system, a laser interferometer is constructed to use the Doppler effect. In order to reduce the driving power of the scanning system, a small displacement of the scanning system is produced, which is achieved by using a magnetostrictive actuator. A sufficient rotating angle of the scanning system is obtained by using an amplified displacement from the resonant phenomena of a second order mechanical system composed of a mass and spring. The control of the magnetostrictive actuator using a Terfenol-D is performed without using a feedback system to help reduce the power consumption. The vibration analysis is made for the sinusoidal scanning input to have the space domain information from the time domain of the velocity of a vibration object. As a partial work of development of a tow power consuming laser scanning vibrometer, in this work, a scanning system which has the above features is developed and experimentally investigated. For the purpose of the optical system calibration, the vibration measurement for one axis is presented and the future works are discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1546-1551
• /
• 2004

The laser Doppler technique is well-established as a velocity measurement technique of high precision for flow velocity. Recently, the laser Doppler technique has also been used to measure acceleration of fluid particles. Acceleration is interesting from a fluid mechanics point of view, since the Navier Stokes equations, specifically the left-hand-side, are formulated in terms of fluid acceleration. Further, there are several avenues to estimating the dissipation rate using the acceleration. However such measurements place additional demands on the design of the optical system; in particular fringe non-uniformity must be held below about 0.0001 to avoid systematic errors. Relations expressing fringe divergence as a function of the optical parameters of the system have been given in the literature; however, direct use of these formulae to minimize fringe divergence lead either to very large measurement volumes or to extremely high intersection angles. This dilemma can be resolved by using an off-axis receiving arrangement, in which the measurement volume is truncated by a pinhole in front of the detection plane. In the present study an optical design study is performed for optimizing laser Doppler systems for fluid acceleration measurements. This is followed by laboratory validation using a round free jet and a stagnation flow, two flows in which either fluid acceleration has been previously measured or in which the acceleration is known analytically. A 90 degree off-axis receiving angle is used with a pinhole or a slit.

• 한국전자파학회논문지
• /
• 제25권1호
• /
• pp.99-107
• /
• 2014

돌발적으로 발생하는 도로 장애물은 고속으로 주행하는 차량의 안전운행을 위협한다. 따라서, 악천후 시에도 도로상의 돌발 장애물을 탐지하고, 충돌을 방지할 수 있는 전천후 레이다 센서에 대한 관심이 높아지고 있다. 본 논문에서는 도로 장애물 탐지 및 경보를 위한 Ka-대역 펄스 도플러 레이다 시험모델의 설계 제작 및 성능시험 결과를 제시한다. 레이다 센서는 도로 환경조건에 적합하고, 다양한 고정 및 이동 장애물에 대하여 탐지, 추적 및 차선 식별 기능이 요구된다. 개발된 레이다는 안테나, 송수신기, 신호처리기 및 제어기로 구성된다. 주요 적용 기술은 고정 장애물 탐지를 위한 클러터 맵 기반 변화 탐지 기법, 이동 장애물 속도 탐지를 위한 도플러 추정 기법, 그리고 차선 식별을 위한 3-horn 모노펄스 방위각 추정 및 추적 기법이 포함된다. 개발된 레이다 시스템의 장애물 탐지와 차량 감시 성능은 성능시험과 환경시험을 통하여 설계 요구 조건을 만족하는 것으로 확인되었다.

• 한국항공우주학회지
• /
• 제43권7호
• /
• pp.648-656
• /
• 2015

능동 합성개구레이더 위성의 주요기동은 SAR 안테나 방향을 바꾸기 위한 롤축 기동이다. 그리고 도플러 중심주파수 변화를 최소화하기 위하여 요축 기동이 요구된다. 따라서 토크/모멘텀 용량을 대부분 롤축으로 그 다음으로 요축으로 할당하는 것이 합리적이다. 하지만 궤도 조정 때문에 가끔씩 피치축으로 중심으로 큰 각도의 회전이 요구된다. 본 논문에서는 롤축과 요축의 연속회전을 통한 피치축 기동시간 단축 방법에 대해서 살펴본다. 이들 두 축이 피치축에 비해서 기동성능이 좋기 때문에, 피치축을 중심으로 큰 회전이 요구될 때는 기동시간 단축이 가능하다.

• 한국분무공학회지
• /
• 제20권1호
• /
• pp.35-42
• /
• 2015

This study is to investigate the spray behavior of DME-LPG blended fuels in common rail injection system for diesel engines. The visualization experiment was performed to analyze the macroscopic spray behavior of test fuels. In addition, the experiment using BOS(Background Oriented Schlieren) method is performed to compare liquid phase and gas phase. The test fuels are injected in high pressure chamber. The ambient pressure of high pressure chamber was formed by nitrogen gas. Spray tip penetration, spray cone angle and spray area were measured using high speed camera. SMD(Sauter Mean Diameter) and spray particle velocity were measured using the PDPA(Phase Doppler Particle Analyzer) system to analyze the microscopic properties of test fuels. The results of this experiment showed that spray tip penetration, spray cone angle and spray area of DME-LPG fuels are similar to those of DME fuel. When compared to results of experiment using BOS, significant differences of spray tip penetrations, spray cone angle and spray area are showed because of gas phase. The results of experiment using BOS method showed higher values. SMD of DME-LPG blended fuels is smaller than that of DME fuel. Velocity of DME-LPG blended fuels is faster than that of DME fuel.

• 설비공학논문집
• /
• 제27권7호
• /
• pp.344-353
• /
• 2015

In the present study the characteristics of turbulent oscillatory flows in a square-sectional $180^{\circ}$curved duct were investigated experimentally. A series of experiments for air flow were conducted to measure axial velocity profiles, secondary flow velocity profiles and pressure distributions. The measurements were made by a Laser Doppler Velocimeter (LDV) system with a data acquisition and processing system which includes Rotating Machinery Resolve (RMR) and PHASE software. The results from the experiment are summarized as follows. (1) The maximum velocity moved toward the outer wall from the region of a bend angle of $30^{\circ}$. The velocity distribution had a positive value extended over the total phase in the region of a bend angle of $150^{\circ}$. (2) Secondary flows were generally proportional to the velocity of the main flow. The intensity of the secondary flow was about 25% as much as that in the axial direction. (3) Pressure distributions were effects of the oscillatory Dean number and respective region.

• 한국전자파학회논문지
• /
• 제29권8호
• /
• pp.615-623
• /
• 2018

낮은 관측각에서의 해상 클러터 반사계수의 진폭 확률밀도 함수는 각 클러터 패치별 평균 세기가 서로 다르므로 Rayleigh 분포가 아닌 compound Gaussian 분포로 가정하는 것이 일반적이다. 반사계수를 구성하는 텍스쳐(texture) 성분은 Gamma 분포 및 MNLT(memoryless nonlinear transformation)를 이용해서 발생시키지만, 스펙클(speckle) 성분 시뮬레이션에 대해서는 정형화된 방법은 없다. 수신 신호의 스펙트럼을 Gaussian 형태의 도플러 스펙트럼 형태로 모델링한 후 스펙클 성분을 발생시킨 기존 S. Watt 방법을 소개한 후 본 논문에서 새롭게 제안한 방법을 제시하였다. 제안 방법은 이퀄라이져(equalizer) 필터를 사용해서 인접 클러터 영향을 최소화한 후, 클러터 공분산 행렬에 대해 Cholesky 분해를 통해서 스펙클 성분을 생성하는 방법으로써 제안 방법의 타당성 검증을 위해 시뮬레이션을 통해 도플러 스펙트럼 및 코릴레이션(correlation) 함수 관점에서 제안한 방법과 기존 방법을 비교한다.

• International Journal of Automotive Technology
• /
• 제5권4호
• /
• pp.221-238
• /
• 2004

Wall interactions of direct injection spray were investigated using laser-sheet imaging, shadowgraphy, wetted footprint and phase Doppler interferometry techniques. A narrow-cone high-pressure swirl injector is used to inject iso-octane fuel onto a plate, which has three different impact angles inside a pressurized chamber. Heated air and plate conditions were compared with unheated cases. Injection interval was also varied in the heated case to compare dry- and wet- wall impingement behaviors. High-speed macroscopic Mie-scattering images showed that presence of wall and air temperature has only minor effect on the bulk spray structure and penetration speed for the narrow-cone injector tested. The overall bulk motions of the spray plume and its spatial position at a given time are basically unaffected until a few millimeters before impacting the wall. The surface properties of the impact surface, such as the temperature, the presence of a preexisting liquid film also have a small effect on the amount of wetting or the wetted footprint; however, they have strong influence on what occurs just after impact or after a film is formed. The shadowgraph in particular shows that the plate temperature has a significant effect on vapor phase propagation. Generally, 10-20% faster horizontal vapor phase propagation is observed along the wall at elevated temperature condition. For impingement onto a preexisting film, more splash and evaporation were also observed. Contrary to some preconceptions, there is no significant splashing and droplet rebounding from surfaces that are interposed in the path of the DI gasoline spray, especially for the oblique impact angle cases. There also appears to be a dense spray front consists of large sac spray droplets in the oblique impact angle cases. The bulk of the spray is not impacted on the surface, but rather is deflected by it The microscopic details as depicted by phase Doppler measurements show that the outcome of the droplet impaction events can be significantly influenced. Only droplets at the spray front have high enough Weber numbers for wall impact to wet, splash or rebound. Using the sign of vertical velocity, the time-resolved downward droplets and upward droplets are compared. The Weber number of upward moving droplets, which seldom exceeds unity, also decreases as the impact angle decreases, as the droplets tend to impact less and move along the wall in the deflected spray plume.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1919-1932
• /
• 1991

본 연구에서는 고강도 알루미늄 합금으로 제작된 평판보의 받음각(.alpha.)를 10˚ 에서 30˚까지 10˚씩 변화시킨 3가지의 모델에 대해, 각 모델의 Re$_{d}$수 변화에 대한 후류의 스펙트럼분석, 레이저 도플러 유속계(laser doppler velocimetry)를 이용 한 유동장 해석 및 평판보의 응답을 실험을 통해 조사, 분석하고 유동장과 측정이 용 이하지 않은 얇은 평판주위의 압력분포에 대한 전산해석을 수행함으로써 유동 여기진 동 구조의 규명을 시도하였다.다.