• 공업화학
• /
• 제26권3호
• /
• pp.306-310
• /
• 2015

본 연구에서는 광 전기화학적 물 분해 전극 재료로 이용되는 산화철($Fe_2O_3$, hematite)을 표면적을 크게 하기 위하여 DC 열플라즈마 장치를 이용하여 나노입자로 합성한 후 전극을 제조 시 binder의 종류 및 조성을 다르게 하여 염기성 전해질에서 각각의 물 분해 효율을 측정하는 실험을 진행하였으며 질소 도핑을 통해 질소가 산화철의 광전기화학 반응에 끼치는 영향을 확인하였다. 산화철 전극을 제조하여 solar simulator를 이용한 LSV 실험을 통해 각 전극의 onset potential 및 설정한 전압 범위에서의 최대 전류밀도를 측정하였으며, 전극의 내구성 평가를 위하여 LSV 실험을 반복하여 진행하였다. CMC (carboxymethyl cellulose)를 50 : 1의 비율로 섞어 binder로 이용한 산화철 전극이 가장 높은 전류밀도인 $12mA/cm^2$의 전류밀도를 나타내었고, CMC를 20 : 1 비율로 섞은 binder를 이용할 시 $3mA/cm^2$의 초기 전류밀도를 가지고 약 20회의 반복 실험을 견뎌내는 내구성을 나타내었다. 질소의 도핑이 산화철 나노입자의 광 전기 화학적 반응에 끼치는 영향은 미미한 것으로 확인되었다.

• 전기화학회지
• /
• 제15권2호
• /
• pp.67-73
• /
• 2012

본 연구에서는 습식분쇄, 구형화 분무건조 및 열처리 공정을 통해 구형의 $LiMn_{2-x}M_xO_4$(M = Al, Mg, B) 스피넬계 양극소재를 합성하고, 이의 전기화학적 성능을 평가하였다. $MnO_2$ (Tosoh, 91.94%), $Li_2CO_3$ (SQM, 97%), $MgCO_3$ (Aldrich, 99%), $Al(OH)_3$ (Aldrich, 99%) 및 $B_2O_3$ (Aldrich, 99%)를 원료로 사용하였으며, 분무건조공정에서 전구체의 구형화도 증가를 위해 PAAH 바인더를 첨가하였다. 200~500 nm 크기로 분쇄된 혼합 슬러리 용액으로부터 분무건조법을 통해 구형의 전구체를 제조하고, 이를 다양한 조건에서 열처리하여 최종 스피넬계 $LiMn_{2-x}M_xO_4$ (M = Al, Mg, B) 양극소재를 제조하였다. 제조된 구형의 $LiMn_{2-x}M_xO_4$ (M = Al, Mg, B) 양극재료는 이종원소 치환량, 특히 Boron 치환량에 따라 입자 표면 및 내부의 치밀도가 변화하는 것을 확인할 수 있었으며, 치밀도가 증가함에 따라 소재의 출력특성이 향상되었으며, 최적 조성의 양극소재는 상온 5 C 용량이 0.2 C 용량 대비 90% 이상이 됨을 확인하였다. 또한 표면의 치밀도도 증가함에 따라 $60^{\circ}C$ 고온 충방전 조건에서 수명특성이 향상되어 500회 사이클 이후에도 초기용량의 80% 이상을 유지하였다.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.68-73
• /
• 2007

We fabricated the in-situ $MgB_2$ wires using the powder-in-tube method and investigated the effects of sintering temperature and SiC contents on the microstructure and superconducting properties. Pure $MgB_2$ wires and 5, 10, 20 wt.% SiC doped $MgB_2$ wires were sintered at $600-1000^{\circ}C$ for 30 minutes in Ar atmosphere. We found that $MgB_2$ phase was mostly formed at the sintering temperature of $700^{\circ}C$ and above, and the critical temperature ($T_c$) increased with increasing sintering temperature. For the $MgB_2$ sintered at $850^{\circ}C$, the highest critical current density ($J_c$) was obtained to be $3.7{\times}10^5\;A/cm^2$ at 5 K and 1.6 T by a magnetic properties measurement system (MPMS). The addition of SiC to the $MgB_2$ wires changed microstructure and critical properties. SEM observation showed that the $MgB_2$ core had considerable micro-cracks in undoped wire and the density of micro-cracks decreased with increasing SiC contents. The critical temperature decreased as the SiC contents increased, on the other hand, the critical current density of SiC doped $MgB_2$ wires in high magnetic field was enhanced compared to that of undoped $MgB_2$ wires.

• 한국분말재료학회지
• /
• 제15권3호
• /
• pp.182-187
• /
• 2008

Carbon was known to be one of effective additives which can improve the flux pinning of $MgB_2$ at high magnetic fields. In this study, glycerin $(C_3H_8O_3)$ was selected as a chemical carbon source for the improvement of critical current density of $MgB_2$. In order to replace some of boron atoms by carbon atoms, the boron powder was heat-treated with liquid glycerin. The glycerin-treated boron powder was mixed with an appropriate amount of magnesium powder to $MgB_2$ composition and the powder pallets were heat treated at $650^{\circ}C\;and\;900^{\circ}C$ for 30 min in a flowing argon gas. It was found that the superconducting transition temperature $(T_c)$ of $Mg(B_{1-x}C_x)_2$ prepared using glycerin-treated boron powder was 36.6 K, which is slightly smaller than $T_c$(37.1 K) of undoped $MgB_2$. The critical current density $(J_c)$ of $Mg(B_{1-x}C_x)_2$ was higher than that of undoped $MgB_2$ and the $T_c$ improvement effect was more remarkable at higher magnetic fields. The $T_c$, decrease and $J_c$ increase associated with the glycerin treatment for boron powder was explained in terms of the carbon substitution to boron site.

• 전기화학회지
• /
• 제24권4호
• /
• pp.77-92
• /
• 2021

전기자동차의 주행거리는 리튬이온전지의 에너지 밀도에 의해 결정된다. 리튬이온전지의 에너지 밀도 향상을 위해서는 단위 질량 당 많은 양의 리튬 이온을 저장할 수 있는 고용량 활물질 소재 개발이 필수적이다. 양극 기술의 급속한 발전은 이론적으로 구현 가능한 최대 용량에 근접한 수준의 가역 용량을 활용할 수 있는 수준에 이르렀다. 반면 음극은 90년대에 도입된 흑연을 현재까지도 주요 활물질로 활용하는데 머무르고 있다. 음극의 용량을 증가시키는 방법으로 고용량-장수명 특성을 지닌 실리콘 산화물 활물질을 음극에 첨가하는 방식이 가장 유력하게 검토되고 있다. 그러나 실리콘 산화물의 낮은 초기 쿨롱 효율은 음극 내 실리콘 산화물의 함량을 15% 이내로 제한하여 음극 용량 증가에 걸림돌이 되고 있다. 이에 따라 실리콘 산화물 등 고용량 음극의 초기 효율을 개선할 수 있는 사전리튬화 기술이 점점 많은 주목을 받고 있다. 본 리뷰논문에서는 사전리튬화 기술의 개념 및 효과에 대해 설명하고 현재까지 개발된 사전리튬화 기술을 반응 방식에 따라 분류하여 소개한다. 특히, 리튬화 반응의 균질성이 높고 대량 양산에 강점을 지닌 용액 기반 화학적 사전리튬화 기술의 최신 개발 동향을 집중적으로 소개하였다. 상용화가 가능한 사전리튬화 기술 개발이 가까운 미래의 차세대 리튬이온전지 음극재 시장의 주도권 확보의 핵심 조건이 될 것으로 기대한다.

• 전자공학회논문지 IE
• /
• 제45권1호
• /
• pp.1-6
• /
• 2008

본 연구에서는 발광층에 2 파장 재료를 갖는 백색 유기발광소자를 진공증착법을 사용하여 청색 발광재료인 NPB와 황색 발광재료인 Rubrene을 사용하여 제작하였다. 제작된 소자는 ITO/NPB$(200{\AA})$NPB:Rubrene$(300{\AA})$/BCP$(100{\AA})/Alq_3(100{\AA})/Al(1000{\AA})$ 구조로 하였고 Rubrene의 도핑농도는 0.75 wt%이었다. 소자의 색좌표값은 인가전압 11 V에서 x = 0.3327, y = 0.3387 로 NTSC 색좌표 순수한 백색영역(x = 0.3333, y = 0.3333)에 근접한 순수한 백색에 가까운 값을 얻었고, 이 때 최대발광파장은 560 nm이었다. 소자의 동작 개시전압은 1 V이하이고 발광 개시전압은 4 V이다. 최대 외부양자효율은 인가전압 18.5 V, 전류밑도 $369mA/cm^2$ 일 때 0.457 %를 얻었다.

• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.87-91
• /
• 2013

The doping effect of Sn on the microstructure evolution and dielectric properties was studied in $CaCu_3Ti_{4-x}Sn_xO_{12}$ polycrystals. Samples were produced by a conventional solid-state reaction method. Sintering was carried out at $1115^{\circ}C$ for 2-16 h in air. The dielectric constant and loss were examined at room temperature over a frequency range between $10^2$ and $10^6$ Hz. The microstructure was found to evolve into three stages. Addition of $SnO_2$ led to an increase in density and advanced formation of abnormal grains. The formation of coarse grains with a reduced thickness of the boundary brought about an enhanced dielectric constant and a lower dielectric loss below ~1 kHz. EDS data showed the Cu-rich phase along the grain boundary, which should contribute to the improved dielectric constant according to the internal barrier layer capacitor model. After all, $SnO_2$ was an effective dopant to elevate the dielectric characteristics of $CaCu_3Ti_{4-x}Sn_xO_{12}$ polycrystals as a promoter for abnormal grain growth.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.86-86
• /
• 2012

The new approaches for silicon solar cell of new concept have been actively conducted. Especially, solar cells with wire array structured radial p-n junctions has attracted considerable attention due to the unique advantages of orthogonalizing the direction of light absorption and charge separation while allowing for improved light scattering and trapping. One-dimenstional semiconductor nano/micro structures should be fabricated for radial p-n junction solar cell. Most of silicon wire and/or pillar arrays have been fabricated by vapour-liquid-solid (VLS) growth because of its simple and cheap process. In the case of the VLS method has some weak points, that is, the incorporation of heavy metal catalysts into the growing silicon wire, the high temperature procedure. We have tried new approaches; one is electrochemical etching, the other is noble metal catalytic etching method to overcome those problems. In this talk, the silicon pillar formation will be characterized by investigating the parameters of the electrochemical etching process such as HF concentration ratio of electrolyte, current density, back contact material, temperature of the solution, and large pre-pattern size and pitch. In the noble metal catalytic etching processes, the effect of solution composition and thickness of metal catalyst on the etching rate and morphologies of silicon was investigated. Finally, radial p-n junction wire arrays were fabricated by spin on doping (phosphor), starting from chemical etched p-Si wire arrays. In/Ga eutectic metal was used for contact metal. The energy conversion efficiency of radial p-n junction solar cell is discussed.

• Bulletin of the Korean Chemical Society
• /
• 제33권10호
• /
• pp.3407-3412
• /
• 2012

The Ti incorporation at Fe-site in the double perovskite lattice of $Sr_2FeNbO_6$ (SFNO) system is studied. The Ti concentration optimization yielded an efficient photocatalyst. At an optimum composition of Ti as x = 0.07 in $Sr_2Fe_{1-x}Ti_xNbO_6$, the photocatalyst exhibited 2 times the quantum yield for photolysis of $H_2O$ in presence of $CH_3OH$, than its undoped counterpart under visible light (${\lambda}{\geq}420nm$). Heavily Ti-doped $Sr_2Fe_{1-x}Ti_xNbO_6$ lattice exhibited poor photochemical properties due to the existence of constituent impurity phases as observed in the structural characterization, as well as deteriorated optical absorption. The higher electron-density acquired by n-type doping seem to be responsible for the more efficient charge separation in $Sr_2Fe_{1-x}Ti_xNbO_6$ (0.05 < x < 0.4) and thus consequently displays higher photocatalytic activity. The Ti incorporated structure also found to yield stable photocatalyst.

• Bulletin of the Korean Chemical Society
• /
• 제34권7호
• /
• pp.2067-2072
• /
• 2013

Hydrogen ($H_2$) treatment using a two-step $TiO_2$ nanotube (TONT) film was performed under various annealing temperatures from $350^{\circ}C$ to $550^{\circ}C$ and significantly influenced the extent of hydrogen treatment in the film. Compared with pure TONT films, the hydrogen-treated TONT (H:TONT) film showed substantial improvement of material features from structural, optical and electronic aspects. In particular, the extent of enhancement was remarkable with increasing annealing temperature. Light absorption by the H:TONT film extended toward the visible region, which was attributable to the formation of sub-band-gap states between the conduction and valence bands, resulting from oxygen vacancies due to the $H_2$ treatment. This increased donor concentration about 1.5 times higher and improved electrical conductivity of the TONT films. Based on these analyses and results, photoelectrochemical (PEC) performance was evaluated and showed that the H:TONT film prepared at $550^{\circ}C$ exhibited optimal PEC performance. Approximately twice higher photocurrent density of 0.967 $mA/cm^2$ at 0.32 V vs. NHE was achieved for the H:TONT film ($550^{\circ}C$) versus 0.43 $mA/cm^2$ for the pure TONT film. Moreover, the solar-to-hydrogen efficiency (STH, ${\eta}$) of the H:TONT film was 0.95%, whereas a 0.52% STH efficiency was acquired for the TONT film. These results demonstrate that hydrogen treatment of TONT film is a simple and effective tool to enhance PEC performance with modifying the properties of the original material.