• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.289-289
• /
• 2013

While there are plenty of studies on synthesizing semiconducting germanium nanowires (Ge NWs) by vapor-liquid-solid (VLS) process, it is difficult to inject dopants into them with uniform dopants distribution due to vapor-solid (VS) deposition. In particular, as precursors and dopants such as germane ($GeH_4$), phosphine ($PH_3$) or diborane ($B_2H_6$) incorporate through sidewall of nanowire, it is hard to obtain the structural and electrical uniformity of Ge NWs. Moreover, the drastic tapered structure of Ge NWs is observed when it is synthesized at high temperature over $400^{\circ}C$ because of excessive VS deposition. In 2006, Emanuel Tutuc et al. demonstrated Ge NW pn junction using p-type shell as depleted layer. However, it could not be prevented from undesirable VS deposition and it still kept the tapered structures of Ge NWs as a result. Herein, we adopt $C_2H_2$ gas in order to passivate Ge NWs with carbon sheath, which makes the entire Ge NWs uniform at even higher temperature over $450^{\circ}C$. We can also synthesize non-tapered and uniformly doped Ge NWs, restricting incorporation of excess germanium on the surface. The Ge NWs with carbon sheath are grown via VLS process on a $Si/SiO_2$ substrate coated 2 nm Au film. Thin Au film is thermally evaporated on a $Si/SiO_2$ substrate. The NW is grown flowing $GeH_4$, HCl, $C_2H_2$ and PH3 for n-type, $B_2H_6$ for p-type at a total pressure of 15 Torr and temperatures of $480{\sim}500^{\circ}C$. Scanning electron microscopy (SEM) reveals clear surface of the Ge NWs synthesized at $500^{\circ}C$. Raman spectroscopy peaked at about ~300 $cm^{-1}$ indicates it is comprised of single crystalline germanium in the core of Ge NWs and it is proved to be covered by thin amorphous carbon by two peaks of 1330 $cm^{-1}$ (D-band) and 1590 $cm^{-1}$ (G-band). Furthermore, the electrical performances of Ge NWs doped with boron and phosphorus are measured by field effect transistor (FET) and they shows typical curves of p-type and n-type FET. It is expected to have general potentials for development of logic devices and solar cells using p-type and n-type Ge NWs with carbon sheath.

• Journal of the Korean Ceramic Society
• /
• v.48 no.1
• /
• pp.94-98
• /
• 2011

A Sn-doped $In_2O_3$ (ITO) nanowire photoelectrode was produced using a simple metal evaporation method at low synthesis temperature (< $540^{\circ}C$). The nanowire electrodes have large surface area compared with that of flat ITO thin film, and show low electrical resistivity of $5.6{\times}10^{-3}{\Omega}cm$ at room temperature. In order to apply ITO nanowires to the photoelectrodes of dye-sensitized solar cell (DSSC), those surfaces were modified by $TiO_2$ nanoparticles using a chemical bath deposition (CBD) method. The conversion efficiency of the fabricated $TiO_2$/ITO nanostructure-based DSSC was obtained at 1.4%, which was increased value by a factor of 6 than one without ITO nanowires photoelectrode. This result is attributed to the large surface area and superior electrical property of the ITO nanowires photoelectrode, as well as the structural advantages, including short diffusion length of photo-induced electrons, of the fabricated $TiO_2$/ITO nanostructure-based DSSC.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.879-882
• /
• 2015

In this work, we have analyzed the characteristics of vertical nanowire GAA MOSFET according to channel width and the type of channel doping through the simulation. First, we compared and analyzed the characteristics of designed structures which have tilted shapes that ends of drains are fixed as 20nm and ends of sources are 30nm, 50nm, 80nm and 110nm. Second, we designed the rectangular structure which has uniform width of drain, channel and source as 50nm. We used it as a standard and designed trapezoidal structure which is tilted so that the end of drain became 20nm and reverse trapezoidal structure which is tilted so that the end of source became 20nm. We compared and analyzed the characteristic of above three structures. For the last, we used the rectangular structure, divided its channel as five parts and changed the type of the five parts of doping concentration variously. In the first simulation, when the channel width is the shortest, in the second, when the structure is trapezoid, in the third, when the center of channel is high doped show the best characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.41-45
• /
• 2003

Impurities transmuted in GaN thin film and GaN nanowires after neutron irradiation are studied in this work. The structural properties of GaN nanowires were shown using by Transmission Electron Microscope(TEM). Transmuted impurities that are expected to be doped into GaN thin film and GaN nanowires are then confirmed by photoluminescence(PL). Transmuted atom in GaN materials is Ge atom, Ge-related peaks in GaN thin film lead to emit at 2.9eV, 2.25eV. But emission bands at 2.9eV, 2.25eV are not shown in PL spectra of GaN nanowires. Our experimental results are expected to give deep impact on nano-material doping technology for the achievement of the fabrication of nano-devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.378-379
• /
• 2012

ITO 만큼 높은 전도성과 광학적 투과성을 갖는 Al-doped ZnO (AZO) 박막을 DC-Pulse magnetron sputtering을 이용하여 40 nm 두께로 증착 후 리소그라피 공정을 통해 $30{\mu}m$ 간격으로 패터닝 하였다. 간격 30 ${\mu}m$로 배열된 AZO를 촉매층으로 하는 수열합성법을 리사이클 공정을 반복하여 수행하여 ZnO 나노선을 성장시켰다. 이와 같이 AZO 전극 사이에 길이 $30{\mu}m$의 ZnO 나노선이 래터럴 구조로 연결된 소자의 $NH_3$ 가스감지 특성을 조사하였다. 합성된 나노선의 전기적, 광학적, 구조적인 특성을 분석하여 높은 가스 감지도를 예상할 수 있는 특성을 확인하였다. 제작된 가스센서를 진공 챔버에 설치 후 양 전극간에 동작전압(Operating voltage)을 1 V로 인가하여 고정한 후에 $NH_3$를 주입(Injection)과 퍼지(Purge)를 반복하며 그 주입량(10 ppm, 20 ppm, 40 ppm, 60 ppm)에 변화를 주었고, 그에 따른 전류변화를 관찰하여 $NH_3$ 가스감지특성을 평가하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.546-550
• /
• 2013

We propose a novel negative differential resistance (NDR) device with ultra-high peak-to-valley current ratio (PVCR) by combining pn junction diode with depletion mode nanowire (NW) transistor, which suppress the valley current with transistor off-leakage level. Band-to-band tunneling (BTBT) Esaki diode with degenerately doped pn junction can provide multiple switching behavior having multi-peak and valley currents. These multiple NDR characteristics can be controlled by doping concentration of tunnel diode and threshold voltage of NW transistor. By designing our NDR device, PVCR can be over $10^4$ at low operation voltage of 0.5 V in a single peak and valley current.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.101-102
• /
• 2006

금속을 도핑 함으로써 전기전도도가 향상될 것으로 생각되는 산화바나듐 나노선에 대하여 열처리 전후의 전기적 특성을 비교하였다. sol-gel 방법으로 만들어진 산화바나듐 xerogel($V_{1.66}Mo_{0.33}O_5{\cdot}nH_2O$)을 $Si_3N_4$ 절연막이 성장된 Si기판위에 분산시키고 Ti/Au으로 전극을 증착한 후 열처리 한 것과 하지 않은 두 시료의 전류-전압특성을 비교 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.160-161
• /
• 2008

$SnO_2$는 n형 반도체로써 3.6 eV의 큰 밴드갭을 가지는 물질로 CO와 NOx 가스에 좋은 감도를 나타내는 것으로 보고되고 있다. 문헌에 따른 일반적인 $SnO_2$ 가스센서는 후막이나 벌크형태로 제작되었다. 근래에는 가스감응체가 $SnO_2$ 나노선 형태인 가스센서가 활발한 연구 중에 있다. 본 논문에서는 기판 위에 서로 분리된 전극 패턴에 Au를 촉매로 하여 네트워크 구조로 된 $SnO_2$ 나노선이 합성되었다. 제작된 가스센서에 Pd 도핑에 따른 영향을 알아보기 위하여 1.8 mM의 Pd 용액 ($PdCl_2{\cdot}xH_2O$ 3 mg + $H_2O$ 10 ml)을 이용하여 센서에 도핑하였다. 측정 시스템에서 $NO_2$ 가스에 대한 센서의 특성을 분석한 결과 도핑하지 않은 $SnO_2$ 센서보다 20%정도의 감도가 개선되었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.463-463
• /
• 2014

Dye-sensitized solar cells (DSSCs) have generated a strong interest in the development of solid-state devices owing to their low cost and simple preparation procedures. Effort has been devoted to the study of electrolytes that allow light-to-electrical power conversion for DSSC applications. Several attempts have been made to substitute the liquid electrolyte in the original solar cells by using (2,2',7,7'-tetrakis (N,N-di-p-methoxyphenylamine)-9-9'-spirobi-fluorene (spiro-OMeTAD) that act as hole conductor [1]. Although efficiencies above 3% have been reached by several groups, here the major challenging is limited photoelectrode thickness ($2{\mu}m$), which is very low due to electron diffusion length (Ln) for spiro-OMeTAD ($4.4{\mu}m$) [2]. In principle, the $TiO_2$ layer can be thicker than had been thought previously. This has important implications for the design of high-efficiency solid-state DSSCs. In the present study, we have fabricated 3-D Transparent Conducting Oxide (TCO) by growing tin-doped indium oxide (ITO) nanowire (NWs) arrays via a vapor transport method [3] and mesoporous $TiO_2$ nanoparticle (NP)-based photoelectrodes were prepared using doctor blade method. Finally optimized light-harvesting solid-state DSSCs is made using 3-D TCO where electron life time is controlled the recombination rate through fast charge collection and also ITO NWs length can be controlled in the range of over $2{\mu}m$ and has been characterized using field emission scanning electron microscopy (FE-SEM). Structural analyses by high-resolution transmission electron microscopy (HRTEM) and X-Ray diffraction (XRD) results reveal that the ITO NWs formed single crystal oriented [100] direction. Also to compare the charge collection properties of conventional NPs based solid-state DSSCs with ITO NWs based solid-state DSSCs, we have studied intensity modulated photovoltage spectroscopy (IMVS), intensity modulated photocurrent spectroscopy (IMPS) and transient open circuit voltages. As a result, above $4{\mu}m$ thick ITO NWs based photoelectrodes with Z907 dye shown the best performing device, exhibiting a short-circuit current density of 7.21 mA cm-2 under simulated solar emission of 100 mW cm-2 associated with an overall power conversion efficiency of 2.80 %. Finally, we achieved the efficiency of 7.5% by applying a CH3NH3PbI3 perovskite sensitizer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.261.2-261.2
• /
• 2013

에너지 갭이 큰 ZnO 반도체는 빛 투과율이 우수하여 투명성이 좋으며 화학적으로 안정된 구조를 가지고 있어 전자소자 및 광소자 응용에 대단히 유용하다. 일반적으로 화학 기상증착, 전자빔증착과 전기화학증착법을 사용하여 ZnO 나노 구조를 제작하고 있다. 여러 가지 증착 방법 중에서 전기화학증착방법은 낮은 온도와 진공 공정이 필요하지 않으며 대면적 공정이 가능하고 빠른 성장 속도로 나노구조를 효과적으로 성장할 수 있는 장점을 가지고 있다. 본 연구에서는 전기화학증착법을 이용하여 Indium Tin Oxide (ITO) 기판위에 Al 도핑된 ZnO 나노세선 성장시키고 성장시간에 따라 형성한 ZnO 나노세선의 구조적 성질을 조사하였다. ZnO 나노세선을 성장하기 위하여 zinc nitrate와 potassium chloride를 각각 0.1 M을 용해한 용액을 사용하였다. 전기화학증착방법을 사용하여 제작한 ITO 기판 위에 성장시킨 ZnO 나노세선 위에 전극을 제작하고 전류-전압 특성을 측정하였다. Al-doped ZnO 나노세선의 성장되는 조건을 Al 농도별로 0 wt%, 1 wt%, 2 wt% 및 5 wt% 씩 증가시키면서 ZnO 나노세선의 구조적 특성을 분석하였다. X-선회절 (X-ray diffraction; XRD) 실험 결과를 통해 ZnO 나노세선이 성장함을 확인하였고, 성장 시간이 길어짐에 따라 (101) 성장방향의 XRD 피크의 세기가 증가하였다. 전기화학증착시 Al 도핑 농도 증가에 따라 ZnO 나노세선의 지름이 200 nm에서 300 nm로 변화하는 것을 주사전자현미경으로 관측하였다. 이 실험 결과는 전기화학증착방법을 사용하여 제작한 ZnO 나노세선의 Al 도핑 농도에 따른 구조적 특성들을 최적화하여 소자제작에 응용하는데 도움이 됨을 보여주고 있다.