• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.256-259
• /
• 2008

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some ejectors with a various of nozzle throat and mixing chamber diameter were manufactured precisely and tested for the comparison with the calculation results.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3191-3196
• /
• 2007

The present study addresses a method to operate a fuel-cell system effectively using a recirculation ejector which recycles wasted hydrogen gas. Configuration of a recirculation ejector is changed to investigate the flow behavior through it under varying operating conditions, and how such conditions affect the fuel-cell hydrogen cycle. The numerical simulations are based on a fully implicit finite volume scheme of the axisymmetric, compressible, Reynolds-Averaged, Navier-Stokes equations for hydrogen gas, and are compared with available experimental data for validation. The results show that a hydrogen recirculation ratio is effectively controlled by a configurational alteration within the operational region in which the recirculation passage doesn't plugged by a sonic line.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.547-550
• /
• 2008

A solid rocket motor has quite complex physical condition such exothermal chemical reaction in subsonic area and supersonic ex pansion in a converging-diverging nozzle. To introduce a simulation tool for compressible flow in supersonic range as well as incompressible chemical reaction zone in a whole rocket nozzle is a essential demand. Since the flow vary subsonic to super sonic, the convergence in computation becomes very low and unstable in a whole domain of rocket motor. This paper reports the 2-D Axisymmetric and simple 3-D solid propellant combustion and flow of gases in rocket motor by using a precondi tioning, shear stress turbulence modeling, AUSM(p). To simulate the simplified combustion process, Double base solid propellant is used to calculate reaction of solid propellant.

• Journal of Navigation and Port Research
• /
• v.33 no.2
• /
• pp.105-110
• /
• 2009

Shipwaves am have harmful effects on ships working on the sea, in a harbour or navigational channel and caused beach erosion, seawall destruction. This study aims to investigate describe the characteristics of the wave pattern generated by an individual model ship tested at different velocities and hull forms for a given water depth and to investigate the variations at a given distance from the sailing line under the same conditions. As a result, the angles a's by model ship tests are smaller than those by real ship ones. Wave heights decreases with an increasing the mid-ship cross sectional area $A_s$. The maximum wave height and period increase rapidly in the subcritical speed, and beyond the critical speed the height and period decrease with increasing depth Froude number. And the period keeps constant with the distance from the sailing line.

• Proceedings of KOSOMES biannual meeting
• /
• 2006.11a
• /
• pp.25-30
• /
• 2006

Marine traffics near Ulsan approaching waters are crossing and converged at the diverging point of No.1 route- No.2 route and No.1 route -No.3 route and are also concentrated at near No1. route approaching area and the headland of cape Gawnjeol. Because the number of berth will increase to 78 from 49 until 2011 due to additional developments, minor modification is expected for the water utilities. This study examined environmental conditions, marine accidental data, marine traffic capacity, traffic flow survery and fisheries zone status near Ulsan approaching water area. Finally, a questionaire survey was carried ou for experts and users to propose new plan.

• Tunnel and Underground Space
• /
• v.28 no.1
• /
• pp.111-124
• /
• 2018

The purpose of this study is to analyze ventilation design factor for network-type double-deck road tunnel that have been developed actively around the world. A numerical analysis was carried out through computational fluid dynamics (CFD) to derive shock loss coefficient that occurs due to the change in cross sectional area at both merging section and diverging section. The model used for the numerical analysis is real-scale model and the reliability of the result is secured by comparing with the coefficient of the previous studies. As a result of this study, shock loss coefficient was calculated depending on the change in cross-sectional area ratio and was higher than the result of previous studies in case of both merging section and diverging section. It is considered that the characteristics of the geometrical structure of network-type double-deck road tunnel have a great impact on shock loss coefficient. Therefore, the result of this study is expected to be helpful for more accurate ventilation design of network-type double-deck road tunnel.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.4
• /
• pp.297-301
• /
• 2008

On-site measurement of ship wave has been carried out in the vicinity of Mokpo inner harbour. The wave data were collected and logged 5Hz by the ultrasonic instrument for 12hour on May 17, 2006. The number of data was 216,000 and the maximum wave height was 81.41cm in normal weather condition. It was found that the wave conditions in this water area are predominantly affected by the ship-generated waved under normal condition. By comparing with the wind-generated waves in the open region which were irregular but with dominant directional characteristics, the existing harbor wave field was much more complex.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.11
• /
• pp.2680-2687
• /
• 2000

The Reynolds equation, incorporating Elrods cavitation algorithm, is discretized on a rectangular grid in computational space through coordinate mapping in order to accurately analyze a herringbone grooved journal bearing of a spindle motor in a computer hard disk drive. The pressure distribution and cavitation area are determined by using the finite volume method. Predicted results are compared to experimental data of previous researchers. It was found that positive pressure is developed within the converging section of the bearing and that a cavity occurs in the diverging section. Cavitation has been neglected in the previous analysis of the herringbone grooved bearing. Load capacity and bearing torque are increased due to the increased of eccentricity and L/D and the decrease of the grooved width ratio. The maximum load capacity was found to occur at a groove angle of 30 degrees while bearing torque remains constant due to the variation of the groove angle. The cavitation region is significantly decreased with the inclusion of herringbone grooves. However, the region increases with the increase of the eccentricity, L/D, groove angle and the rotational speed and the decrease of the grooved width ratio.

• Journal of Korean Society of Rural Planning
• /
• v.25 no.1
• /
• pp.39-50
• /
• 2019

The purpose of this study is to figure out the current condition of local governments (Si or Gun) to implement rural development policy in the face of the central government's drive for increasing devolution. Since late 1990s or early 2000s when scope of rural policy began to expand quantitatively, there has been considerable increase in rural residents' participation into community projects as a whole. Nevertheless, there exists regional differentiation in local governments' efforts to systematically support rural development projects (CRDP: Comprehensive Rural Development Programme) and community activities by setting up intermediary organizations or hiring rural development professionals in a public office. According to this survey on local government officials, regions that have made such efforts to support rural policy at a local level, show more advanced level of institutional capacity than other regions in local decision making process for CRDP, role of strategic rural developmental plans, vitality of community actors, etc. In the era of increasing devolution, these differences can be expected to result in diverging performances of each area in regionalized rural policy. The central government needs to introduce EU's LEADER-type rural development programmes to support community acitivities by various local actors and at the same time promote local governance building for rural policy, adopting institutional rewarding system such as rural planning contract.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2873-2878
• /
• 2023

The purpose of this study is to perform radiation monitoring by acquiring gamma images and real-time optical images for ^99mTc vial source using charge couple device (CCD) cameras equipped with the proposed compact gamma camera. The compact gamma camera measures 86×65×78.5 mm³ and weighs 934 g. It is equipped with a metal 3D printed diverging collimator manufactured in a 45 field of view (FOV) to detect the location of the source. The circuit's system uses system-on-chip (SoC) and field-programmable-gate-array (FPGA) to establish a good connection between hardware and software. In detection modules, the photodetector (multi-pixel photon counters) is tiled at 8×8 to expand the activation area and improve sensitivity. The gadolinium aluminium gallium garnet (GAGG) measuring 0.5×0.5×3.5 mm³ was arranged in 38×38 arrays. Intrinsic and extrinsic performance tests such as energy spectrum, uniformity, and system sensitivity for other radioisotopes, and sensitivity evaluation at edges within FOV were conducted. The compact gamma camera can be mounted on unmanned equipment such as drones and robots that require miniaturization and light weight, so a wide range of applications in various fields are possible.