• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1A
• /
• pp.132-141
• /
• 2000

In this paper, we proposed the MAC protocol of APON supporting multi-class traffic such as CBBUVBR, ABR, UBR, to guarantee the required QoS of each service. For this, we analyze the performance of variousrequest mechanisms and employee the different request mechanism for each traffic classes. Upstream anddownstream frame structures to minimize transmission overhead are proposed based on our request mechanism.The proposed MAC protocol applies the different priority to permit distribution process. CBBWBR traffic, withthe stringent requirements on CDV or delay, is allocated prior to any other class. ABR traffic, which hasnon-strict CDV or delay criteria, uses flexibly the available bandwidth but ensures a minimum cell rate (MCR).UBR traffic is allocated with lowest priority for the remaining capacity. The performance of proposed protocol isevaluated in terms of transfer delay and 1-point CDV with various offered load. The result of simulation showsthat the proposed protocol guarantees the required QoS of the corresponding category, while making use of theavailable resources in both an efficient and dynamical way.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.7B
• /
• pp.719-726
• /
• 2002

In WRC-2000, Resolution 734 was adopted to study the use of high altitude platform station(HAPS) operating in the bands above 30GHz. Therefore, frequency sharing feasibility between a new HAPS systems and an existing terrestrial fixed-service(FS) system should be analyzed primarily. In this paper, interference effects from the HAPS system into the radio-relay station are analyzed in terms of two cases; one is the interference distribution from the power-flux density(PFD) of HAPS airships, and the other the interference power from the ground stations. In conclusion, the new PFD criteria different from the exiting satellite system should be required, and the coordinated distance between the HAPS nadir and the radio-relay station should be 60km ∼ 253km for P$\sub$HG/ = -50dBW/MHz of transmitting power spectral density to share the new HAPS system into the existing FS system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.12B
• /
• pp.1601-1610
• /
• 2011

This paper discusses standardization activities, requirements and enabling technologies for 100G Ethernet and 100G OTN. The need of 100Gbps transport capacity has been gaining greater interest from service providers and carrier vendors. Moreover, optical transport networks based on OTN/DWDM are changing their properties to apply Ethernet traffic which is dramatically increasing. We realize and experimentally demonstrate OTU4 framer with commercial FPGA. The key features of the realized OTU4 framer are parallel signal processing function, multi-lane distribution function, GMP function and FEC function. The realized OTU4 framer has the large signal processing capacity of 120Gbps, which allows to transport about 120Gbps client signals such as $12{\times}10G$ Ethernet and $3{\times}40G$ Ethernet. The realized OTU4 framer has the advantages to quickly adjust to changing markets and new technologies by using commercial FPGA instead of ASIC.

• Journal of the Korean Data and Information Science Society
• /
• v.22 no.2
• /
• pp.323-333
• /
• 2011

Recently, Electronic Data Interchange (EDI) systems are widely used. Many organizations exchange the documents by using EDI, and EDI is used in various industries such as physical distribution, export and import business, custom, and medical care. However, there have been little attempt to empirically investigate the success factors of EDI system. In this paper, we identify the influencing factors which determine the success of typical information system and then suggest the additional factors characterized to the EDI system. Our research model, mainly based on the system success model, is tested by analyzing the empirical data acquired from the companies in the medical industry. As a result, the system quality, information quality, service quality, and the perceived sacrifice turned out to be significant to the success of EDI system while data security does not. The result of this research is likely to help providing useful guidelines for the successful EDI implementations.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.2
• /
• pp.29-39
• /
• 2018

In this paper, we discuss a discrete-time queueing system with dyadic server control policy that combines workload control and multiple vacations. Customers arrive at the system with Bernoulli arrival process. If there is no customer to serve in the system, an idle single server spends a vacation of discrete random variable V and returns. The server repeats the vacation until the total service time of waiting customers exceeds the predetermined workload threshold D. In this paper, we derived the steady-state workload distribution of a discrete-time queueing system which is operating under a more realistic and flexible server control policy. Mean workload is also derived as a performance measure. The results are basis for the analysis of system performance measures such as queue lengths, waiting time, and sojourn time.

• Geophysics and Geophysical Exploration
• /
• v.7 no.1
• /
• pp.62-69
• /
• 2004

The objective of this study is to estimate the distribution of a zone disturbed by excavation (EDZ) around tunnels that have been excavated at about 500 m depth in pre-Tertiary hard sedimentary rock. One of the most important tasks is to evaluate changes in the dynamic stability and permeability of the rock around the tunnels, by investigating the properties of the rock after the excavation. We performed resistivity and acoustic tomography using two boreholes, 5 m in length, drilled horizontally from the wall of a tunnel in pre-Tertiary hard conglomerate. By these methods, we detected a low-resistivity and low-velocity zone 1 m in thickness around the wall of the tunnel. The resulting profiles were verified by permeability and evaporation tests performed at the same boreholes. This anomalous zone matched a high-permeability zone caused by open fractures. Next, we performed resistivity monitoring along annular survey lines in a tunnel excavated in pre-Tertiary hard shale by a tunnel-boring machine (TBM). We detected anomalous zones in 2D resistivity profiles surrounding the tunnel. A low-resistivity zone 1 m in thickness was detected around the tunnel when one year had passed after the excavation. However, two years later, the resistivity around the tunnel had increased in a portion, about 30 cm in thickness, of this zone. To investigate this change, we studied the relationship between groundwater flow from the surroundings and evaporation from the wall around the tunnel. These features were verified by the relationship between the resistivity and porosity of rocks obtained by laboratory tests on core samples. Furthermore, the profiles matched well with highly permeable zones detected by permeability and evaporation tests at a horizontal borehole drilled near the survey line. We conclude that the anomalous zones in these profiles indicate the EDZ around the tunnel.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1612-1627
• /
• 2008

Dwelling time is one of the factors that influence in rail. Current research in dwelling time has been focusing on railways, the state of the research in high-speed rail's dwelling time is not complete. Dwelling time is consisted of time to open door, time to get into and out of vehicle and time of the departure it takes after the passenger's door was closed, it was affected by various factors such as congestion's degree in vehicle, the number of persons that get into and out of vehicle, congestion's degree in station. In order to analyze theses, we need data analysis such as the number of persons that get into and out of vehicle, congestion's degree in station, congestion's degree in vehicle, but the congestion's degree and passenger's distribution chart in vehicle is excluded in this research due to difficulty of gathering data, and thus we will develop forecasting models through high-speed rail's demand most affected by the dwelling time.

• Journal of Digital Convergence
• /
• v.11 no.3
• /
• pp.181-187
• /
• 2013

Moreover a new logistics concept is needed through the sharing information between suppliers and consumers, which maximizes the level of customers service and its flexibility by changing functional-oriented to process-oriented. In other words, Supply Chain Management(SCM) is now considered as a key aspect of business, which controls the flows of information, funds, and goods in the supply chain. Rationalization of transport-delivery system will be one of the most important issues on logistics management to the domestic companies. The companies need the effective delivery system. Especially in the case of delivery system from distribution centers to customers or vendors, it might take a long time to control the delivery system manually because it would be hard to apply the automatic vehicle routing algorithm effectively considering all the practical constraints. Thus this study develops a heuristic algorithm of automatic vehicle delivery support system in terms of grouping by short ranges of vehicle movement utilizing postal coordinates, which satisfies a variety of realistic constraints and reduces controlling time of manual operations.

• Journal of KIISE
• /
• v.42 no.2
• /
• pp.213-219
• /
• 2015

Simulation is used these days to verify the hypothesis or the new technology. In particular, National Defense Modeling & Simulation (M&S) is used to predict wartime situation and conduct the military training. National Defense M&S can be divided into three parts, live simulation, virtual simulation, and constructive simulation. Live simulation is based on the real environment, which allows more realistic sumulation; however, it has decreased budget efficiency, but reduced depictions of reality. In contrast, virtual and constructive simulations which are based on the virtual environment, have increased budget efficiency, but reduced depictions of reality. Thus, if the three parts of the M&S are combined to make the L-V-C combined environment, the disadvantages of each simulation can be complemented to increases the quality of the simulation. In this paper, a method of interworking heterogeneous simulation middeware for L-V-C combined environment is proposed, and the test results of interworking between Data Distribution Service (DDS) and High Level Architecture (HLA) are shown.

• Nuclear Engineering and Technology
• /
• v.46 no.6
• /
• pp.869-874
• /
• 2014

It was discovered in a Korean PWR that an extensive number of very short and shallow cracks in the SG tubes were undetectable by eddy current in-service-inspection because of the masking effect of sludge deposits. Axial stress corrosion cracks at the outside diameter of the steam generator tubes near the line contacts with the tube support plates are the major concern among the six identical Korean nuclear power plants having CE-type steam generators with Alloy 600 high temperature mill annealed tubes, HU3&4 and HB3~6. The tubes in HB3&4 have a less susceptible microstructure so that the onset of ODSCC was substantially delayed compared to HU3&4 whose tubes are most susceptible to ODSCC among the six units. The numbers of cracks detected by the eddy current inspection jumped drastically after the steam generators of HB4 were chemically cleaned. The purpose of the chemical cleaning was to mitigate stress corrosion cracking by removing the heavy sludge deposit, since a corrosive environment is formed in the occluded region under the sludge deposit. SGCC also enhances the detection capability of the eddy current inspection at the same time. Measurement of the size of each crack using the motorized rotating pancake coil probe indicated that the cracks in HB4 were shorter and substantially shallower than the cracks in HU3&4. It is believed that the cracks were shorter and shallower because the microstructure of the tubes in HB4 is less susceptible to ODSCC. It was readily understood from the size distribution of the cracks and the quantitative information available on the probability of detection that most cracks in HB4 had been undetected until the steam generators were chemically cleaned.