• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.248-251
• /
• 2009

We have investigated the effect of the quality of 1.3 um distributed feed back laser diode (DFB-LD) on the design of anti-reflection (AR) coatings. Optimal condition of AR coating to prevent internal feedback from both facets and reduce the reflection-induced intensity noise of laser diode was simulated with Macleod Simulator. Coating materials used in this work were ${Ti_3}{O_5}$ and $SiO_2$, of which design thickness were 105 nm and 165 nm, respectively. AR coating films were deposited by Ion-Assisted Deposition system. The electrical and optical properties of 1.3 um laser diode were characterized by Bar tester and Chip tester. Threshold current and slop-efficiency of DFB-LD were 27.56 mA 0.302 W/A. Far field pattern and wavelength of DFB-LD were $22.3^{\circ}(Horizontal){\times}24.4^{\circ}$ (Vertical), 1313.8 nm, respectively.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.113-119
• /
• 1994

We fabricated and characterized RWG-DFB-LDs emitting at $1.3\mu\textrm{m}$ wavelength. For fabrication of the laser diode, inteference fringe of optical beams was used for grating formation and epi layers were grown by LPE. The fablicated RWG-DFB-LD operated in a single longitudinal mode with more than 30 dB SMSR at 1296.5 nm emitting wavelength and its threshold current was 67 mA. Coupling coefficient (K) was estimated as $40cm^{-1}$ by means of stop-band measurement. Finally, we show that the RWG-DFB-LD fabricated in this experiment can be applicable as light source of 2.5 Gbps optical communication system from the fact that the small signal response of the RWG-DFB-LD rated up to 1.99 GHz at pre-bias level of $1.2 I_{th}$..

• ETRI Journal
• /
• v.45 no.2
• /
• pp.193-202
• /
• 2023

We demonstrate the transmission of uncompressed 4K videos over the photonics-based terahertz (THz) wireless link using a directly modulated distributed feedback laser diode (DFB-LD). For optical heterodyne mixing and data modulation, a DFB-LD was employed and directly modulated with a 5.94-Gb/s non-return-to-zero signal, which is related to a 6G-serial digital interface standard to support ultra-high-definition video resolution. We derived the optimal frequency of the THz carrier by varying the wavelength difference between DFB-LD output and Tunable LD output in the THz signal transmitter to obtain the best transmission performances of the uncompressed 4K video signals. Furthermore, we exploited the negative laser-to-filter detuning for the adiabatic chirp management of the DFB-LD by the intentional discrepancy between the center wavelength of the optical band-pass filter and the output wavelength of the DFB-LD. With the help of the abovementioned methods, we successfully transmitted uncompressed 4K video signals over the 2.3-m wireless transmission distance without black frames induced by time synchronization error.

• Current Optics and Photonics
• /
• v.4 no.6
• /
• pp.461-465
• /
• 2020

A dual-mode laser terahertz source consisting of two in-line distributed Bragg reflector (DBR) laser diodes (LD) is proposed. It is less susceptible to residual reflections from facets than an in-line dual-mode distributed feedback (DFB) LD. The characteristics of the proposed terahertz source are theoretically investigated using a split-step time-domain simulation. It is shown that terahertz waves of frequencies from 385 GHz to 1725 GHz can be generated by appropriate thermal tuning of two DBR LDs. The dual-mode DBR LD terahertz source exhibits good spectral quality for residual facet reflectivity below 0.02, but facet reflectivity of the in-line dual-mode DFB LD terahertz source should be below 0.002 to provide similar spectral quality.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.5
• /
• pp.1372-1383
• /
• 1998

In this paper, modeling for DC and AC characteristics analysis of DFB-LD was performed considering effects of .lambda./4-shifted gratingandspatial hole burning within a laser diode cavity. From the simulation for DC characteristics, Light-Current curve, optical power distribution and carrier density distribution within the cavity can be obtained. The simulation for AC characteristics porovides IM response and the amplitude and phase and the amplitude and phase response of FM with excellent accuracy.

• ETRI Journal
• /
• v.25 no.3
• /
• pp.149-155
• /
• 2003

A self-pulsating multisection distributed-feedback laser diode (DFB LD) can potentially realize all-optical clock extraction. This device generally consists of three sections, two DFB sections and one waveguide section. The most important variable in this device is detuning, which is the relative spectral position between the stop bands of two DFB sections. We fabricated a novel structure in which two gratings were located one over and one under the active layers. Each grating structure was independently defined in processing so that detuning, which is the prerequisite for self-pulsation, could be easily controlled. Observing various self-pulsating phenomena in these devices under several detuning conditions, we characterized the phenomena as dispersive Q-switching, mode beating, and self-mode-locking.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.96-99
• /
• 2005

As the demand of internet networks using backbone communication systems recently increased, the researches on the high-speed wideband optical communication systems are required. For high-speed optical communication systems, asymmetric sampled grating distributed feedback laser diodes (DFB-LDs) are developed and the reliability of DFB-LDs is examined. The reliability of DFB-LDs is performed by monitoring I-V and L-I characteristics and two degradation phenomena related to the electrical characteristics of LDs are observed during the life tests. The first degradation phenomenon by increasing the reverse current is considered as a formation of leakage current path enough to prevent lasing operation in lateral blocking layer near active region of lasers. The second degradation phenomenon by decreasing the forward current is considered as activation of non-radiative Auger recombination process by thermal energy and the second degradation phenomenon is recovered after the off-test period at room temperature Eventually, evaluating the reliability of DFB LDs can allow us to improved the manufacturability in high-volume manufacturing.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.423-430
• /
• 1994

We designed and fabricated the single mode fiber pigtailed DFB-LD module for 2.5 Gbps optical communication system. In the design of the DFB-LD module, we made the module divided into two parts of inner sub-module and outer 14-pin butterfly package and cylindrical shaped sub-module contain quasi confocal 2 lens system including optical isolator and electrical connection between these parts via hybrid substrate of bias T circuit. Laser welding was used to assemble the sub-module which requires accurate fixing between optical elements. The fabricated DFB-LD module showed optical coupling efficiency of 20% and - 3 dB small signal response of more than 2.6 GHz. We confirmed mechanical reliability of the module by temperature cycle test where the tested module exhibit optical power fluctuation of less than 10%. Finally we evaluated the performance of the fabricated DFB-LD module as light source of 2.5 Gbps optical communication system, sensitivity of - 30.2 dBm was obtained through 47 km optical fiber transmission under the criterion of $1\times10^{-10}$ BER and transmission penalties were 1.5 dB caused by extinction ratio and 1.0 dB caused by chromatic dispersion of normal single mode fiber. fiber.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.68-72
• /
• 1997

Using one of the absorption lines of $^{13}C_2H_2$ molecules near the zero dispersion wavelength(1549.49nm) of dispersion shifted fiber, we stabilized center frequency of an optical fiber Fabry-Perot filter. The free spectral range of the filter is 100 GHz for 100 GHz channel allocation. For equi-spaced three channel multiplexing, channel locking of three DFB-LDs to transmission peaks of the fiber Fabry-Perot filter was tried. To investigate the effect of dithering current applied to each DFB-LD, the change of DFB-LD linewidth was measured.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.823-828
• /
• 2011

We have systematically designed and experimentally demonstrated the opto-electrical predistortion optical transmitter using microwave circuit modelling for reducing the nonlinearity of the distributed-feedback laser diode (DFD-LD). The DFB-LD is analyzed using microwave circuits model based on rate equations. Through the system-level simulation for predistortion method, the optimized characteristics of the RF components in the system are confirmed. The simulated and experimental results show the reduced distortion products. These results are analyzed as the evaluation parameters for the miniaturization and optimization of the opto-electrical predistortion method in radio-over-fiber systems.