• Journal of the Optical Society of Korea
• /
• v.17 no.1
• /
• pp.50-56
• /
• 2013

Optical-fiber electronic speckle pattern interferometry (ESPI) is a non-contact, non-destructive examination technique with the advantages of rapid measurement, high accuracy, and full-field measurement. The optical-fiber ESPI system used in this study was compact and portable with the advantages of easy set-up and signal acquisition. By suitably configuring the optical-fiber ESPI system, producing an image signal in a charge-coupled device camera, and periodically modulating beam phases, we obtained phase information from the speckle pattern using a four-step phase shifting algorithm. Moreover, we compared the actual defect size with that of interference fringes which appeared on a screen after calculating the pixel value according to the distance between the object and the CCD camera. Conventional methods of measuring defects are time-consuming and resource-intensive because the estimated values are relative. However, our simple method could quantitatively estimate the defect length by carrying out numerical analysis for obtaining values on the X-axis in a line profile. The results showed reliable values for average error rates and a decrease in the error rate with increasing defect length or pressure.

• Journal of Forest and Environmental Science
• /
• v.39 no.4
• /
• pp.254-260
• /
• 2023

A sensor system has been developed that uses an ultrasonic sensor to detect the downhill slope on the side of a forest road and prevents a vehicle-type forest machine from rolling down a mountainside. A specular reflection of ultrasonic wave might cause severe issues in measuring distances to targets. By investigating the installation angle of the sensor to minimize the negative effects of specular reflection, the installation angle of lateral monitoring ultrasonic sensor could be determined based on the width of road shoulder. Obstacles such as small rocks or piece of log in a forest road may cause the forest machine to be overturned while the machine riding over due to excessive its posture change. It was determined that the laser sensor could be a part of a sensor system capable of specifying the location and size of small obstacles. Not only this sensor system including ultrasonic and laser sensors can issue a warning of dangerous sections to drivers in forest forwarders currently in use, but also it can be used as a driving safety sensor in autonomous forest machine or remote-control forest machine in the future.

• Journal of KIISE:Databases
• /
• v.32 no.1
• /
• pp.56-70
• /
• 2005

The results of location-dependent queries(LDQ) generally depend on the current locations of query issuers. Many mechanisms, e.g. broadcast scheme, hoarding, or racking policy, have been developed to improve the system peformance and provide better services, which are specialized for LDQs. Considering geographical adjacency of data and characteristics oi target area, caching policy and broadcast scheme affect the overall performance in LDQ. For this reason, we propose both the caching policy and broadcast scheme, which these features are reflected in. Based on the adjacency of data in LDQ, our broadcast scheme use Hilbert curve to cluster data. Moreover, in order to develop the caching policy suitable for LDQ on urban area, we apply the moving distance of a MH(Mobile Host) to our caching policy We evaluate the performance of the caching policy measuring the workload of MHs and the correctness of LDQ results and the performance of the broadcast scheme measuring the average setup-time of MHs in our experiments. Finally, we expect that our caching policy Provides more correct answers when executing LDQ in focal cache and leads significant improvement of the performance of MHs. It also seems quite probable that our broadcast scheme leads improvement of battery life of the MH.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.15-24
• /
• 2007

Two kinds of temperature monitoring technology have been introduced in this study, which can measure coincidently temperatures at many points along a single length of cable. One is to use a thermal sensor cable comprizing of addressable thermal sensors. The other is to use an optic fiber sensor with Distributed Temperature Sensing (DTS) system. The differences between two technologies can be summarized as follows: A thermal sensor cable has a concept of "point sensing" that can measure temperature only at a predefined position. The accuracy and resolution of temperature measurement are up to the capability of the individual thermal sensor. On the other hand, an optic fiber sensor has a concept of "distributed sensing" because temperature is measured practically at all points along the fiber optic cable by analysing the intensity of Raman back-scattering when a laser pulse travels along the fiber. Thus, the temperature resolution depends on the measuring distance, measuring time and spatial resolution. The purpose of this study is to investigate the applicability of two different temperature monitoring techniques in technical and economical sense. To this end, diverse experiments with two techniques were performed and two techniques are applied under the same condition. Considering the results, the thermal sensor cable will be well applicable to the assessment of groundwater flow, geothermal distribution and grouting efficiency within about loom distance, and the optic fiber sensor will be suitable for long distance such as pipe line inspection, tunnel fire detection and power line monitoring etc.

• Journal of Radiation Industry
• /
• v.17 no.1
• /
• pp.1-9
• /
• 2023

Since a large amount of radioactive waste is expected to be generated due to permanent shutdown of many nuclear power plants, it is necessary to prepare efficient management methods for radioactive waste. Therefore, there is a need for a based study to apply the In-Situ gamma spectrometry, which can simplify the measurement procedure. The purpose of this study is to analyze research cases of In-Situ gamma spectrometry and to analyze the sensitivity of measurement according to influencing factors on In-Situ gamma spectrometry. Research cases of five institutions, including the CERN and the Imperial College Reactor Centre (ICRC), were selected as the institutions to be investigated. Research on the In-Situ gamma spectrometry was conducted on the satisfaction of the acceptance criteria for radioactive waste and the analysis of residual radioactivity in the site. In-Situ Objective Counting System (ISOCS) was used as a major measuring device. Sampling and computer code were used to verify the analysis results. For evaluation of measuring sensitivity according to influencing factors on In-Situ gamma spectrometry, the thickness of the measurement target, the distance between the detector and the target, the angle of the collimator, and the contamination location were performed using ISOCS's Geometry Composer. In every case, based on 122 keV, the efficiency decreased as the energy increased in the high energy region, and the efficiency decreased as the energy decreased in the low energy region. As the target thickness increased, the efficiency decreased, and as the distance between target and detector increased, the efficiency decreased. As the distance between contamination and detector increased, the efficiency decreased, and as the angle of the collimator increased, the measurement efficiency increased. However, when simulating the measurement situation using Geometry Composer, the background is not considered, and the probability of incident in the background increases as the angle increases, so further research needs to be conducted in consideration of these. This study can be utilized when applying the In-Situ gamma spectrometry of radioactive waste clearance in the future.

• Journal of Platform Technology
• /
• v.10 no.2
• /
• pp.10-19
• /
• 2022

Moving assistant devices for people who are difficult to move are becoming electric-powered and automated. These moving assistant devices are not suitable for moving stairs at which the height between floor surfaces is different because these devices are designed and manufactured for flatland moving. An electric-powered and automated moving assistant device should change direction or stop when it approaches stairs in a movement direction. If the user or automatic control system does not change direction or stop in time, a moving assistant device can roll over or collide with stairs. In this paper, we propose a stairs detection method by using oblique distance measured by one sensor tilted to flatland. The method proposed in this paper can detect upward or downward stairs by using a difference between a predicted and measured oblique distance in considering a tilted angle of a sensor for measuring an oblique distance and installation height of the sensor on a moving object. Before the device enters a stairs region, if our proposed method provides information about detected stairs to a device's controller, the controller can do adequate action to avoid the accident.

• Journal of Biomedical Engineering Research
• /
• v.16 no.4
• /
• pp.525-532
• /
• 1995

In this paper, a new try to measure nonlinear propagation characteristics of the pulse along blood vessel by using bispectral analysis is introduced, and the possibility of its application to the medical diagnosis is shown. In this method, the waveforms of pulse motion of blood vessel at two separated measuring points on the wall were detected from Doppler frequency modulation of transmitted probing ultrasonic waves. Then the auto- and crossbispectrum of detected waveforms are calculated to estimate the quadratic NTF (nonlinear transfer function) between the two measuring positions. In order to show relationships between the NTF and the nonlinear propagation characteristics, computer simulations have been performed. As the propagation distance increases, harmonic frequency components in NTF increases broadly due to the nonlinear effect in the propagation of blood pulse. In order to represent this phenomena quantitatively, we propose a new parameter, dispersion ratio of WTF. Basic experimental system was constructed by using 3.5MHz probing ultrasonic waves and the preliminary experiments were carried out on ague phantom and human body. Experimental results showed the validity of the measurement system enoughly.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.8
• /
• pp.381-389
• /
• 2007

In this paper, the measuring method of underwater acoustic communication channel characteristics in the shallow water using the autocorrelation characteristic of PN sequence and the undorwater communication channel analysis results from the received signal sample data are described. For measuring the underwater acoustic communication channel characteristics, two PN sequences are used as a transmitted data of I-channel and Q-channel of QPSK symbol and QPSK signal is transmitted with symbol rate of 5 kHz and carrier frequency of 25 kHz. In the receiver the received signal, which pass through 675 m and 1492 m, is sampled and then stored. Using the stored sample data, the scattering function, coherent time, delay power profile, spaced-tone autocorrelation function, delay spread, and coherent bandwidth of each propagation distance cases are analyzed. Based on the analysis results, several guidelines are suggested for the design and implementation of underwater transmission system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.10
• /
• pp.115-120
• /
• 2009

In this parer, we design the artificial intelligent direction escape light control system to improve/complete the defects of the existing fire fighting system, and sketch an optimum escape guide algorithm for its implementation. It intends to minimize human casualties and injuries by calculating/predicting moving line of the optimum emergency escape, by means of interlocking the sensor and the reception group and analyzing the data of the combustion point and the smoke movement. The optimum escape algorithm is designed by FLOYD algorithm which calculates the shortest distance. It consists of the measuring method which calculates the shortest distance by using hazardous factors for each condition in danger which is judged by the sensor installed in each area.

• Journal of Animal Environmental Science
• /
• v.8 no.3
• /
• pp.171-176
• /
• 2002

Physical parameters of milk cow were measured to design and build RMS(Robotic Milking System) with a tape-measurer and body parameter measurer. The parameters are very important variables to design an RMS. For the working zone space of an RMS manipulator and the movement blunting of milk cow, an interval frame was installed on the stall bottom, and then cow's behavioral reactions were tested. The results from this study is summarized as follow. 1. On the general physical condition measurement, the maximum, minimum and average body length of cow which is related to the space that the manipulator could work into the RMS were 175cm, 144cm, and 163cm respectively. It appeared that the average distance between bottom and chest was 60cm. 2. The average length between fore teats, fore and hind teats and hind teats were 178mm, 150mm and 95mm respectively. It appeared that the average length between bottom and teat attachments was 544mm, and the average length between fore teats and tail-end was 331mm. 3. Although a cow kept a some extent length between hind legs for milking, it looked a stable pose. However, the cow kept a some extent distance between front legs for milking, it looked a unstable pose. Based on results of this test, an interval frame of stall bottom should be installed around the position which was located at its hind legs.