• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.30-35
• /
• 2022

In a nuclear reactor, gamma radiation is the dominant energy deposition in non-fuel regions. Heat is generated upon gamma deposition and consequently affects the mechanical and thermal structure of the material. Therefore, the safety of samples should be carefully considered so that their integrity and quality can be retained. To evaluate relevant parameters, an in-core gamma thermometer (GT) was used to measure gamma heating (GH) throughout the operation of the McMaster nuclear reactor (MNR) at four irradiation sites. Additionally, a Monte Carlo reactor physics code (Serpent-2) was utilized to model the MNR with the GT located in the same irradiation sites used in the measurement to verify its predictions against measured GH. This research aids in the development of modeling, calculation, and prediction of the GH utilizing Serpent-2 as well as implementing a new GH measurement at the MNR core. After all uncertainties were quantified for both approaches, comparable GH profiles were observed between the measurements and calculations. In addition, the GH values found in the four sites represent a strong level of radiation based on the distance of the sample from the core. In this study, the maximum and minimum GH values were found at 0.32 ± 0.05 W/g and 0.15 ± 0.02 W/g, respectively, corresponding to 320 Sv/s and 150 Sv/s. These values are crucial to be considered whenever sample is planned to be irradiated inside the MNR core.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.18 no.4
• /
• pp.185-194
• /
• 2023

Currently, drones are used in various fields such as transportation, agriculture and military. Especially, drones for military use are developed and utilized in many ways such as reconnaissance and bombing to minimize one's own damages. Nevertheless, they are developed as new weapons of modern types, so it is difficult to use them together with existing weapons. In this study, a drone program for effective bombing of mortar, which is often used in modern warfare, is developed. In mortar, a forward soldier comprehends the location of enemy for its distance and altitude, input them in data computer of launching angle, and applies the result value to cannon to launch. However, the existing method has low accuracy of bombing because observing shall be done within 1km from the target, and measuring accurate direction and velocity of the wind is difficult. Whereas, in the program of this study, the location of target, GPS, direction and velocity of the wind, and altitude are measured through drone. Each digit is used to calculate bombing specification for optimal bombing through the calculating formula of launching angle. In addition, when specifications are input in the program, the calculation is done automatically, so that it can be used in various mortars and shells. With the use of the program in this study, the location of enemy can be comprehended, and bombing specifications can be calculated quickly. It also enables the intensity of the wind to be applied for accurate bombing.

• Geomechanics and Engineering
• /
• v.29 no.5
• /
• pp.523-533
• /
• 2022

Several prediction model of penetration rate (PR) of tunnel boring machines (TBMs) have been focused on applying to design stage. In construction stage, however, the expected PR and its trends are changed during tunneling owing to TBM excavation skills and the gap between the investigated and actual geological conditions. Monitoring the PR during tunneling is crucial to rescheduling the excavation plan in real-time. This study proposes a sequential prediction method applicable in the construction stage. Geological and TBM operating data are collected from Gunpo cable tunnel in Korea, and preprocessed through normalization and augmentation. The results show that the sequential prediction for 1 ring unit prediction distance (UPD) is R²≥0.79; whereas, a one-step prediction is R²≤0.30. In modeling algorithm, a gradient boosted regression tree (GBRT) outperformed a least square-based linear regression in sequential prediction method. For practical use, a simple equation between the R² and UPD is proposed. When UPD increases R² decreases exponentially; In particular, UPD at R²=0.60 is calculated as 28 rings using the equation. Such a time interval will provide enough time for decision-making. Evidently, the UPD can be adjusted depending on other project and the R² value targeted by an operator. Therefore, a calculation process for the equation between the R² and UPD is addressed.

• Advances in Energy Research
• /
• v.8 no.2
• /
• pp.111-123
• /
• 2022

Solar Energy is the energy of solar radiation carried by them in the form of heat and light. It can be converted into electricity. Solar potential depends on the site's atmosphere; the solar energy distribution depends on many factors, e.g., turbidity, cloud types, pollution levels, solar altitude, etc. We estimated solar radiation with the help of the Ashrae clear-sky model for three locations in Pakistan, namely Pasni, Gwadar, and Jiwani. As these locations are close to each other as compared to the distance between the sun and earth, therefore a slight change of latitude and longitude does not make any difference in the calculation of direct beam solar radiation (BSR), diffuse solar radiation (DSR), and global solar radiation (GSR). A modified formula for declination angle is also developed and presented. We also created two different models for Ashrae constants. The values of these constants are compared with the standard Ashrae Model. A good agreement is observed when we used these constants to calculate BSR, DSR, GSR, the Root mean square error (RMSE), Mean Absolute error (MABE), Mean Absolute percent error (MAPE), and chisquare (χ²) values are in acceptance range, indicating the validity of the models.

• Journal of Wind Energy
• /
• v.10 no.4
• /
• pp.20-27
• /
• 2019

High-speed shaft coupling in a wind power system transmits power and absorbs variations in length and spindle dislocation between the gearbox and generator. Furthermore, the coupling has an insulation function that prevents electrical corrosion caused by the flow of the generator's current into the gearbox and prevents overload resulting from sudden power failure from being transferred to the gearbox. Its design, functions, and part verification are described in the IEC61400 and GL Guidelines, which specify that the part must have a durability life of 20 years or longer under distance variation and axial misalignment between the gearbox and the generator. This study presents the design of a high-speed coupling through composite stiffness calculation, structural analysis, and comparative analysis of test and theory to identify the characteristics of high-speed coupling for a large-capacity 6 MW wind power generator. A prototype was fabricated by optimizing the manufacturing process for each part based on the design, and the reliability of the fabricated prototype was verified by evaluating the performance of the target quantitative evaluation items.

• Steel and Composite Structures
• /
• v.45 no.4
• /
• pp.513-533
• /
• 2022

This study presents similarities and differences between Turkish Building Code for Steel Structures, which are TS 648 and SDCCSS (Specification for Design, Calculation and Construction of Steel Structures) in terms of the design of the members. Hot-rolled I-shaped steel sections for symmetrical and U-shaped steel sections (i.e., channels) for monosymmetric sections were elaborated in detail. The design strength of tension members under tensile load, compression members under axial load and flexural members under flexure and shear were examined separately. Connection details for tension members, slenderness for compression members and distance between lateral supports for flexural members were considered as prime variables. Analysis results revealed the design strength of the tension members where at least one of the cross-sectional parts is not connected to the connection plates, I-shaped compression members where a slenderness ratio is below 39 (𝛌<39), U-shaped compression members and flexural members where L_b is between L_p and L_r (L_pb≤L_r) designed based on TS 648 are greater than those designed based on SDCCSS 2018. Strength differences between the specification can reach 79% for tensile members, 13% for compression members and 9% for flexural members.

• Structural Engineering and Mechanics
• /
• v.91 no.1
• /
• pp.25-38
• /
• 2024

After the mainshock, whether the train can be allowed to pass the bridges plays an important role in ensuring the transport of supplies and rescue works for example, in the "12 May" earthquake in China, after evaluation, the bridge was still used for transportation in rescue at a very slow speed, engineers usually evaluate whether the train can pass the bridge safely based on the experience, lacks sufficient calculation basis and does not fully consider the risk caused by aftershocks. To address this issue, this paper comprehensively considers the randomness of track irregularity, the randomness of aftershock intensity and other multiple random sources in train-bridge interaction system (TBIS). The sensitivity of train to various random parameters after earthquake is analyzed from the perspective of probability, the most sensitive random variable in this paper is PGA of aftershocks, both for bridge and trailer car, With the increase of epicentral distance, the sensitivity of PGA will decrease, and correspondingly, for trailer car, the sensitivity of other random variables will increase, research in this paper provides a basis for the subsequent random analysis of post-earthquake driving safety.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.5
• /
• pp.473-479
• /
• 2004

In this paper, power density in near field is calculated about analytic object which has comparatively large volume in considering used wavelength such as cellular base station antenna. Panel sector antenna which is used widespreadly in domestic cellular wireless communication system is modeled and electromagnetic field distribution in reactive near field region is calculated by FDTD (Finite Difference Time Domain) method. After that, antenna gain in far field region is obtain by near to far transformation. Power spectral density in radiated near field is calculated in applying to gain-based model with antenna gain in far field. Finally, compliance distance is obtained in considering the result from radiated near field calculation and basic restrictions on occupational and general public exposure limits in ICNIRP guideline. In the center of main radiating position, the result from gain-based model is -14.55 ㏈m and the result from surface scanning method is -15.75 ㏈m. When the losses from cables and connectors used in measurement are considered, the results from gain-based model and surface scanning method are nearly coincident.

• Progress in Medical Physics
• /
• v.12 no.1
• /
• pp.71-77
• /
• 2001

The region, near the edge of a radiation beam, where the dose changes rapidly according to the distance from the beam axis is known as the penumbra. There is a sharp dose gradient zone even in megavoltage photon beams due to source size, collimator, lead alloy block, other accessories, and internal scatter ray. We investigate dosimetric characteristics on penumbra regions of a standard collimator and compare to those of theoritical model for the optimal use of the system in radiotherapy. Peripheral dose distribution of 6 W Photon beams represents penumbral forming function as the depth. Also we have discussed that the peripheral dose distribution of clinical photon beams, differences between calculation dose use of emperical penumbral forming function and measurements in penumbral region. Predictions by emperical penumbral forming functions are compared with measurements in 3-dimensional water phantom and it is shown that the method is capable of reproduceing the measured peripheral dose values usually to within the statistical uncertainties of the data. The semiconductor detector and ion chamber were positioned at a dmax depth, 5cm depth, 10cm depth, and its specific ratio was determined using a scanning data. The effective penumbra, the distance from 80% to 20% isodose lines were analyzed as a function of the distance. The extent of penumbra will also expand with depth increase. Difference of measurement value and model functions value according to character of the detector show small error in dose distribution of the peripheral dose.

• Progress in Medical Physics
• /
• v.13 no.4
• /
• pp.187-194
• /
• 2002

In this work we investigated through Monte Carlo calculations the physical characteristics of the absorbed dose from the Ir-192 source used in brachytherapy The Monte Carlo calculations were performed using the code EGS4, which was extensively modified in order to handle cylindrical sources, phantoms, and energy distributions to suit out own purpose. From the results of the calculations for the $\beta$ -rays, it was found that they contribute on the average 0.02% to The total absorbed dose in the distance range of 0.5-5.0 cm from the source. This is due to the face that, although most of the primary $\beta$ -rays are absorbed in the source and encapsulation material, the resulting low energy braking radiation from them contribute to such a distance. The absorbed dose in the encapsulation material varied on the average from 2.8% for platinum down to 1.1% for iron. The radial dose functions obtained by our Monte Carlo calculations were consistent within $\pm$3% with those of the TG-43 report for the radial distance interval 0.5-10.0 cm from the source. The user code we wrote in this work can be used for other sources of different sizes and so it can be very useful in designing and producing the sources for brachytherapy.