• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.919-922
• /
• 2003

This paper presents a novel low power driving circuit for passive matrix organic lighting emitting diodes (OLED) displays. The proposed driving method for a low power OLED driving circuit which reduce large parasitic capacitance in OLED panel only use current driving method, instead of mixed mode driving method which uses voltage pre-charge technique. The driving circuit is implemented to one chip using 0.35${\mu}{\textrm}{m}$ CMOS process with 18V high voltage devices and it is applicable to 96(R.G.B)X64, 65K color OLED displays for mobile phone application. The maximum switching power dissipation of driving power dissipation is 5.7mW and it is 4% of that of the conventional driving circuit.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.203-203
• /
• 2013

Low pressure plasmas play a key role in many areas including electronic, aerospace, automotive, biomedical, and toxic waste management industries, and the advantages of the plasma are well known the processing procedure is established. However, the insight behavior of the discharges remains a mystery, even though a simple geometry as capacitive discharges. In this work, we measured RF power dissipation in capacitively coupled plasma (CCP) at various experiment conditions with potential probe and RF current probe. Through the results, we will have a clearer view of the inner nature of the CCP.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 C
• /
• pp.1079-1081
• /
• 1998

This paper describes the dissipation factor measuring device for insulating oil in operating pole transformer by DSP(digital signal processor). After applying voltage to the sensor which is installed in a transformer, acquire source voltage and current of sensor using FFT techniques, then we could evaluate the dissipation factor of insulating oil. To improve measuring accuracy and processing speed, we use TMS320C31 DSP, FFT and data analysis techniques. Also we suggest deterioration criterion of insulating oil and compared the developed diagnosis device with schering bridge on deteriorated insulating oil. The result of this paper show that the developed measuring device can be used as diagnosis device for the pole transformers.

• Structural Engineering and Mechanics
• /
• 제26권3호
• /
• pp.231-250
• /
• 2007

The influence of masonry infills with eccentric openings on the seismic performance of reinforced concrete (r/c) frames that were designed in accordance with current code provisions are investigated. Eight 1/3-scale, single-story, single-bay frame specimens were tested under cyclic horizontal loading up to a drift level of 4%. In all examined cases the shear strength of columns was higher than the cracking shear strength of solid infill. The parameters investigated include the shape and the location of the opening. Assessment of the behavior of the frames is also attempted, based on the observed failure modes, strength, stiffness, ductility, energy dissipation capacity and degradation from cycling loading. Based on these results there can be deduced that masonry infills with eccentrically located openings has been proven to be beneficial to the seismic capacity of the bare r/c frames in terms of strength, stiffness, ductility and energy dissipation. The location of the opening must be as near to the edge of the infill as possible in order to provide an improvement in the performance of the infilled frame.

• Steel and Composite Structures
• /
• 제27권4호
• /
• pp.439-451
• /
• 2018

In the present investigation, a plane P (longitudinal) wave is made incident upon a transversely isotropic magnetothermoelastic solid slab of uniform thickness, interposed between two different semi-infinite viscoelastic solids. The transversely isotropic magnetothermoelastic sandwiched layer is homogeneous with combined effects of two temperature, rotation and Hall current in the context of GN Type-II and Type-III (1993) theory of thermoelasticity. The amplitude ratios of various reflected and refracted waves are obtained by using appropriate boundary conditions. The effect of energy dissipation on various amplitude ratios of longitudinal wave with angle of incidence are depicted graphically. Some cases of interest are also deduced from the present investigation.

• ETRI Journal
• /
• 제33권6호
• /
• pp.880-886
• /
• 2011

With the introduction of high-current 8-inch solar cells, conventional Schottky bypass diodes, usually adopted in photovoltaic (PV) panels to prevent the hot spot phenomenon, are becoming ineffective as they cause relatively high voltage drops with associated undue power consumption. In this paper, we present the architecture of an active circuit that reduces the aforementioned power dissipation by profitably replacing the bypass diode through a power MOS switch with its embedded driving circuitry. Experimental prototypes were fabricated and tested, showing that the proposed solution allows a reduction of the power dissipation by more than 70% compared to conventional Schottky diodes. The whole circuit does not require a dedicated DC power and is fully compatible with standard CMOS technologies. This enables its integration, even directly on the panel, thereby opening new scenarios for next generation PV systems.

• 한국전기전자재료학회논문지
• /
• 제25권10호
• /
• pp.817-823
• /
• 2012

Insulation breakdown of water-cooled generator stator windings occurs frequently due to leakage of cooling water and absorption into the insulation material. Leakage and absorption problems of water-cooled stator windings are often found during regular preventive maintenance. To evaluate cooling water leakage and absorption, diagnostic tests were performed on two water-cooled turbine generators, which have been in service for 13 and 17 years, respectively. The test results of the measured electrical properties such as dissipation factor($tan{\delta}$), capacitance and AC leakage current for water-cooled generator stator windings with wet bars are reported in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.232-234
• /
• 1996

The self-refresh mode was introduced as method to reduce power dissipation in DRAM. Because the data retention time of DRAM cell decreases as the ambient temperature rises, the internal period in self-refresh mode must be limited by retention capability at the highest temperature in DRAM specification. Because of this, at room temperature($25^{\circ}C$) unnecessary power dissipation happens, If the period of self-refresh could be modulated as temperature, it is possible to reduce the self-refresh current. In this paper, new temperature detector circuit is suggested as this purpose.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제23권3호
• /
• pp.157-178
• /
• 2019

The present correspondence is conveyed on to consider the fascinating and novel characteristics of radiative hydromagnetic convective flow of a chemically reacting fluid over an exponentially accelerated inclined porous plate. Exact solutions for the fluid velocity, temperature and species concentration, under Boussinesq approximation, are obtained in closed form by the two term perturbation technique. The interesting parts of thermal dispersing outcomes are accounted in this correspondence. Graphical evaluation is appeared to depict the trademark direct of introduced parameters on non dimensional velocity, temperature and concentration profiles. Also, the numerical assortment for skin friction coefficient, Nusselt number and Sherwood number is examined through tables. The certification of current examination is confirmed by making an examination with past revelations available in composing, which sets a benchmark for utilization of computational approach.

• Structural Engineering and Mechanics
• /
• 제82권2호
• /
• pp.259-270
• /
• 2022

The paper investigates the residual stresses arising in a thermoviscoelastic cylinder as a result of layer-by-layer deposition of material on its lateral surface. Internal stresses are caused by incompatible deformations that accumulate in the assembly as a result of joining parts with different temperatures. For the analysis of internal stresses, an analytical solution to the axisymmetric quasi-static problem of thermoelasticity for a growing cylinder is constructed. It is shown that the distribution of residual stresses depends on the scenario of the surfacing process. In this case, the supply of additional heat to the growing body can significantly reduce the unevenness of temperature fields and reduce the intensity of residual stresses. The most effective is uneven heating, which can be realized, by the action of an alternating current with a tunable excitation frequency. The temperature and residual stresses fields on the growing surface is analyzed numerically for Titanium and Copper materials.