• Proceedings of the Korea Information Processing Society Conference
• /
• 2004.05a
• /
• pp.797-800
• /
• 2004

FED(Field Emission Display)는 CRT(Cathode Ray Tube)의 화질과 LCD(Liquid Crystal Display)와 같은 FPD(Flat Panel Display)의 경량, 박형의 장점을 만족시키는 차세대 Display 소자로서 주목을 받고 있다. 본 논문은 저항열을 이용하여 256 Gray-Scale Level을 출력하는 8 비트 FED Data Driver IC 설계에 관한 것이다. 즉, 저항열과 D/A 변환기를 통하여 디지털 입력 데이터에 따른 아날로그 출력 데이터를 갖는 FED 용 Data Driver IC이다. 본 논문에서 설계된 Driver IC는 집적도를 높여 Output Channel 수를 증가시키는 것을 목표로, 하이닉스 0.6um High Voltage 공정을 사용하였으며, 8 비트 RGB 데이터 입력과 40V 구동전압에서 동작하도록 설계하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1236-1239
• /
• 2009

Each LCD TFT panel requires a power supply IC on the panel board. The IC provides the power rails for the timing controller, source and gated driver IC and others. The industry trend moves towards higher integrated devices. The challenge for the panel manufacturer is the development and implementation of such an IC in cooperation with the semiconductor supplier. If not done carefully the solution will not reduce the overall solution cost or can't provide the expected performance and reliability. This paper discusses the key considerations to successfully develop and integrate a highly integrated LCD bias IC into the system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.381-384
• /
• 2005

Driver IC is one of the key components on the LCD monitor and LCD/TV. The function of the driver IC is to transfer and forward the input signals to LCD panel module. Inside driver IC, there are several operating units which process the input signals and generate the appropriate size and resolution to the LCD panel module. LCD panel module will display these input signals. However, there are some difficulties which driver IC designer, LCD monitor and LCD/TV maker will face. Thus, this article addresses the function and difficulties on driver IC.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.293-296
• /
• 2002

This paper proposes new driving methods for designing a driver independent of the current property of organic light emitting diodes (OLED) displays. The proposed methods are the Look-Up Table (LUT) and the Pulse Width Modulation (PWM). The LUT is used to handle the amount of the current for driving the OLED display panel and the PWM is applied to represent the gray scale on the OLED display panel. Segment and common drivers were implemented using delay circuits to prevent short-circuit current and a DC-DC converter was designed to supply the drivers with a power source. In particular, tile proposed methods are used for the manufacturing of 1.8" 128$\times$128 dot passive matrix OLED display panel. The designed circuit was fabricated using 0.6w, 2-poly, 3-metal, CMOS process and applied to the Personal Communication System (PCS) phone successfully.ully.

• Proceedings of the Safety Management and Science Conference
• /
• 2009.04a
• /
• pp.523-529
• /
• 2009

The ACF(Anisotropic Conductive Film) is used for bonding Drive IC and OLED display device panel. If ACF bonding process is problem, a malfunction of line defect can occur. Because electric resistance increase between the panel and drive IC after a period of time, drive IC can not supply enough current to the panel. This paper is studied on a method of test for line defect.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.127-130
• /
• 2008

A 2.2" QVGA($320{\times}240$) 262,114 color AMOLED module has been developed using digital driving methodology. In this paper, we discuss the development of diver IC which is applied to Digital AMOLED module. Technologies for low cost IC structure and image quality enhancement are presented.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.288-290
• /
• 2014

In this paper, Escape and BTA(Bus Turn Around) modes of master bridge IC are implemented, which supports MIPI(Mobile Industry Processor Interface) DSI(Display Serial Interface) standard. MIPI DSI master bridge IC sends RGB data and various commands to display module(slave) in order to test it. The Escape mode is designed to implement LPDT, ULPS and trigger message transmissions. The BTA mode is designed to obtain various status information from slave in reverse direction. Functional simulation results show that the designed Escape and BTA modes work correctly for various conditions defined in MIPI DSI standard.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.291-292
• /
• 2014

High-speed video transmission modes of master bridge IC are implemented, which supports MIPI (Mobile Industry Processor Interface) DSI (Display Serial Interface) standard. MIPI DSI master bridge IC sends RGB data and various commands to display module (slave) in order to test it. The master bridge IC consists of buffers storing video data of two lines, packet generation block, and D-PHY layer that distributes packets to data lanes and transmits them to slave. In addition, it supports four bpp (bit per pixel) formats and three transmission modes including Burst and Non-Burst (Sync Events, Sync Pulses types). The designed bridge IC is verified by RTL simulations showing that it functions correctly for various operating parameters.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1275-1282
• /
• 2012

This paper proposes the 16-channel LED Driver IC for Full color LED display system. The proposed LED driver IC in this paper can draw current independent of temperature and supply voltage in each channel. Current flow in the channel is configurable via an external resistor. LED brightness is adjusted by 12-Bit PWM(Pulse Width Modulation) and 8-Bit DC(Dot Correction). A real-time monitoring of IC temperature ($130^{\circ}C/150^{\circ}C$) and LED status (open/short) is provided by LED driver IC and the user can receive warning and get information on problems. A 16-channel LED driver IC is produced using 0.35 um BCD process and the size is $2.5mm{\times}2.5mm$. In this paper, channel current characteristic and channel current control function were measured in order to verify am embodied 16-channel LED driver IC by producing a single IC test board.

• Analytical Science and Technology
• /
• v.21 no.4
• /
• pp.284-295
• /
• 2008

For plastics samples, a method using combustion ion chromatography was selected as a method for rapid low-cost analysis to test whether hazardous substances are contained or not. Using combustion ion chromatography, a verification test for F, Cl and Br compounds generated a linear calibration curve with a correlation coefficient of $r^2$ = 0.999~1.000 in the calibration range from 0.5 to 4.0 mg/kg. The detection limits were found to be 0.005~0.024 mg/kg and quantitative limits were found to be 0.014~0.073 mg/kg. The recoveries of combustion ion chromatography using certified reference material (CRM) were found to be 95.5~104.9%. Based on these results, a proficiency test was conducted together with several laboratories in and out of the country, to make comparative analysis of the results from each laboratory. As a result, the data supported the use of combustion ion chromatography as an effective analysis method to deal with regulations for halogen-free electronic products and for other hazardous substances in the electronic products.