• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.8
• /
• pp.721-728
• /
• 2017

High-grade gray cast iron (HCI350) was prepared by adding Cr, Mo and Cu to the gray cast iron (GC300). Their microstructure, mechanical properties and fatigue strength were studied. Cast iron was made from round bar and plate-type castings, and was cut and polished to measure the percentage of each microstructure. The size of flake graphite decreased due to additives, while the structure of high density pearlite increased in volume percentage improving the tensile strength and fatigue strength. Based on the fatigue life data obtained from the fatigue test results, the probability - stress - life (P-S-N) curve was calculated using the 2-parameter Weibull distribution to which the maximum likelihood method was applied. The P-S-N curve showed that the fatigue strength of HCI350 was significantly improved and the dispersion of life data was lower than that of GC300. However, the fatigue life according to fatigue stress alleviation increased further. Data for reliability life design was presented by quantitatively showing the allowable stress value for the required life cycle number using the calculated P-S-N curve.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.2
• /
• pp.165-170
• /
• 2014

Shear horizontal (SH) waves propagate as a type of plate wave in a thin sheet. The dispersion characteristics of SH waves can be used for signal analysis. Therefore, SH-waves are useful for monitoring the structural health of a thin-sheet-structure. An electromagnetic acoustic transducer (EMAT), which is a non-contact ultrasonic transducer, can generate SH-waves easily by varying the shape and array of magnets and coils. Therefore, an EMAT can be applied to an automated ultrasonic testing system for structural health monitoring. When used as a sensor, however, the EMAT has a weakness in that electromagnetic interference (EMI) noise can occur easily in the automated system because of motors and electric devices. Alternatively, a fiber optic sensor works well in the same environment with EMI noise because it uses a light signal instead of an electric signal. In this paper, a fiber Fabry-P$\acute{e}$rot interferometer (FFPI) was proposed as a sensor to receive the SH-waves generated by an EMAT. A simple test was performed to verify the performance of the FFPI sensor. It is thus shown that the FFPI can receive SH-wave signals clearly.

• Korea Real Estate Review
• /
• v.27 no.3
• /
• pp.87-102
• /
• 2017

The purpose of this study was to compare the taxation equity of non-residential collective real estate based on its standard market prices set by National Tax Service and those for taxation set by the Ministry of Government Administration and Home Affairs with that of the apartment houses in Seoul, South Korea. The study findings were as follows. First, the analysis results of the standard market price rates of non-residential collective real estate pointed to a huge gap in the assessment rate (AR) of the taxation standards among the Gu offices. Second, there was a big coefficient of dispersion (COD) in the standard market prices of non-residential collective real estate, which confirmed the presence of horizontal inequity. Finally, there was regressive vertical inequity, which leads to the undervaluation of high-value assets, in the standard market prices of non-residential collective real estate. The evaluation of the standard market prices of non-residential collective real state should thus reflect the market prices and the addition and assessment of the land and buildings to achieve taxation equity. Based on these findings, it is hoped that this study will make a significant contribution to the improvement of the official announcement system for non-residential real estate based on real transactions during the shift to such system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.677-684
• /
• 2014

In response to possible HNS (Hazardous and Noxious Substance) spill accident, HNS spill accident scenario and response scenario were developed. The accident area listed in scenarios is the coastal area of Busan, and scenario for possible accident in the designated area and strategies to respond the accident were developed, respectively. The scenario for accident was developed by designating HNS spill according to risk evaluation of HNS and analysis of HNS spill probability along the coastal area of Busan, and then estimating possible and potential impact from the accident. The scenario for response has been suggested as a systematical responding operations in order to effectively reduce the estimated impact from the accident. The possible HNS spill accident on the seas around Busan, has been designated by the spillage of 1,000ton of xylene due to collision accident in Gamcheon Port, and the possible impacts occurred by the accident has been simulated with the help of the atmospheric and oceanic dispersion model of xylene. In the responding scenario for the accident, a phased strategies regarding emergency rescue of peoples, protection and recovery of xylene, protective measures for the responders, and post management of the accident have been suggested.

• Korean Journal of Optics and Photonics
• /
• v.28 no.5
• /
• pp.194-202
• /
• 2017

The purpose of this study is to analyze how optics concepts and activities have changed according to the revision of the national science curriculum. For this purpose, the optics achievement standards presented in the middle-school science curriculum of the 7th curriculum, 2007 revised curriculum, 2009 revised curriculum, and 2015 revised curriculum, and the optics content presented in the textbooks developed for each curriculum, were compared and analyzed. The optics content is classified into four concepts: the process of viewing an object; light and color; reflection and refraction; and the image from a mirror and a lens. The main results are as follows: First, according to the revision of curriculum, some optics concepts have been added or removed. In particular, big changes have appeared in the concepts of "process of viewing the object", "dispersion", "reflection and refraction" and so on. Second, the content for 'image formation by a mirror and a lens' was gradually reduced, according to the revision of curriculum, and the level of activity was also adjusted. Third, attempts to present the content of textbooks in conjunction with the phenomena and tools that students can experience in everyday life have increased gradually. In addition, based on the analysis of the content of curriculum and textbooks, the implications for optics education have been discussed.

• Membrane Journal
• /
• v.29 no.1
• /
• pp.51-60
• /
• 2019

In order to improve gas separation properties of polymeric membranes which have been widely applied in the industry field, aluminosilicate hollow nanoparticles named as allophanes were synthesized by sol-gel method and formulated in Poly(dimethylsiloxane) (PDMS) matrix to investigate the gas separation properties of PDMS membrane. Transmission electron microscope (TEM), Energy dispersive X-ray analysis (EDX), X-ray diffractometer (XRD), Surface area and pore size analyzer (BET) and Fourier transform infrared spectrophotometer (FTIR) were carried out to characterize the synthetic allophanes. Then the PDMS mixed matrix membranes were prepared by adding different volume fraction of allophanes. To examine the effect of allophanes addition in PDMS matrix using unmodified allophane and modified ones, the gas permeation experiments were performed using oxygen, nitrogen, methane and carbon dioxide. As the volume fraction of modified allophane increased up to 4.05 Vol% the permeability of four test gases through PDMS mixed matrix membranes increased. Also, the selectivity of $O_2/N_2$ and $CO_2/CH_4$ increased with the contents of the modified allophane. Further improvement of gas separation properties of PDMS mixed matrix membranes containing higher volume percent of allophanes can be expected as long as well dispersion of allophanes in PDMS matrix can be achieved for better PDMS membranes.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.575-583
• /
• 2019

The results of the catalytic reaction by pulsed injection of reactants are useful for studying the initial reaction characteristics in the case of many coke invloved reactions. The dehydrogenation characteristics of alumina supported platinum tin catalysts were investigated by pulsed injection of propane. The yield of propylene was maximized when the reduction time of propane injection catalyst was $550^{\circ}C$. Raman analysis showed that the amount of coke was very small when PtSn (4.5) catalyst was used and the short contact time was simulated by propane pulse injection. n order to differentiate the degree of dispersion of platinum, PtSn (4.5) catalyst was sintered at $900^{\circ}C$ with hydrogen, and then the temperature of air - redispersion was varied and propane pulse was injected. As a result, conversione and yield were the highest when air-redispersion temperature is $600^{\circ}C$. The lower the air-redispersion temperature, the higher the selectivity. As the tin content in the platinum catalyst increased, the propane conversion was lowered, but the selectivity to propylene increased and the yield increased. From this, it can be seen that the tin-added platinum catalyst is less active than the platinum catalyst from the beginning of the reaction, which is less affected by coke. The dehydrogenation reaction by the propane pulse injection shows a higher conversion rate than the result of continuous injection due to the formation of COx, and the amount of coke is very small. Decrease in selectivity due to the formation of COx can be reduced by increasing the reduction temperature and time.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.349-356
• /
• 2018

In this study, material properties of steel fiber reinforced high strength concrete (FRHSC) with the compressive strength of about 120MPa were modeled. Steel fiber content of 1.0%, 1.5%, and 2.0% was considered as experimental variable. First of all, compressive strength tests were carried out to determine compressive characteristics of concrete, and compressive stress-strain curves were modeled. For conventional concrete with moderate compressive strength, the stress-strain curves are in the form of parabolic curves, but in the case of high strength concrete reinforced with steel fiber, the curves increase linearly in the form of the straight line. In addition, to understand the tensile properties of FRHSC, the crack mouth opening displacement (CMOD) test was performed, and the tensile stress-CMOD curve was calculated through inverse analysis. When the steel fiber content increased from 1.0% to 1.5%, there was a significant difference of tensile strength. However, when the amount of steel fiber was increased from 1.5% to 2.0%, there was no significant difference of tensile strength, which might result from the poor dispersion and arrangement of steel fiber in concrete.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.20-28
• /
• 2019

This study comparatively analyzes general walking shoes on the conical top foundation of the ground condition and the pressure distribution during walking with shoes that are currently under development. Two categories of footwear were used: general footwear and a footwear conical top foundation that is currently under development. Experiments were carried out on hard ground and sandy soil in 15 male twenties that satisfy the conditions of normal foot wearing 260 mm. The pressure during walking was measured using Techstorm's Wireless Insole System, and foot pressure was measured in 7 zones of the foot. Studies have shown different maximum forces, average pressures, and pressure distributions depending on the shoe and ground conditions. This study shows that shoes with general low pressure dispersion effects depending on the feet in hard ground and sand ground are different from shoes with the conical top foundation that is currently under development. It is expected that it will be useful for the development of shoes that can be worn in all hard ground and sandy ground by selecting various rubber materials through further research.

• Korean Journal of Heritage: History & Science
• /
• v.36
• /
• pp.241-266
• /
• 2003

Glass pieces excavated from Mireuksa Temple dated $7^{th}$ century A.D. were characterized by chemical composition, specific gravity and melting point. Lead isotope ratios of lead glasses were also compared with those of lead ore to attribute which lead ore was delivered for making lead glass. It was known that some lead glasses found in Japan were similar with those of Mireuksa Temple as comparing the data of chemical composition and lead isotope ratios. Characteristics of lead glass from Mireuksa Temple Thirty five glass pieces of Mireuksa Temple were analyzed for five oxides and found that all was lead glass system(PbO-$SiO_2$) with the range of 70~79% for PbO and 20~28% for $SiO_2$. The concentrations of oxides such as $Al_2O_3$, $Fe_2O_3$ and CuO were below 0.4%, 0.3% and 0.9%, respectively. Principal component analysis(PCA) as a statistical method was carried out to classify glasses with the similarities of chemical concentrations. The result of PCA has shown that three groups of glasses were created according to the excavation positions and two major oxides(PbO and $SiO_2$) greatly contributed to the dispersion of glasses on principal component 1(PC1) axis and trace element oxides($Al_2O_3$ and $Fe_2O_3$) for PC2 axis. Most of lead glasses were greenish by the efficacy of iron and copper oxides and some showed yellowish-green. The gravity of lead glasses was about 4.4~5.4 and estimated melting point was near $670^{\circ}C$. Lead isotope ratios of glasses were analyzed and found quite close to a lead ore from the Bupyeong mine in Gyeonggi-do. Comparison with lead glasses found in Japan Lead glasses of Mireuksa Temple were compared with those of Japan on the basis of chemical and physical data. Chemical compositions of Japanese lead glasses dated $7^{th}{\sim}8^{th}$ century A.D. were nearly similar with those of Mireuksa Temple but lead isotope ratios of those were separated into two groups. Three distribution maps of lead ores of Korea, Japan and China with lead isotope ratios were applied for lead glasses found in Japan. The result have shown that the locations of lead glasses from Fukuoka Prefecture coincided with the region of northen part of Korea and similar with those of Mireuksa Temple and lead glasses from Nara Prefecture dated $8^{th}$ century A.D. were located in the region of Japanese lead ore. This research has demonstrated that lead glasses of Mireuksa Temple conveyed to Miyajidake site, Fukuoka Prefecture around $7^{th}$ century A.D. and glass melting pots and glass beads excavated from Nara Prefecture confirmed the first use of Japanese lead ore for production of lead glasses from the end of $7^{th}$ century A.D.