• 열처리공학회지
• /
• 제7권1호
• /
• pp.44-52
• /
• 1994

In order to investigate the effect of tempring treatment on the mechanical properties of ausformed martensite in Fe-30%Ni-0.35%C alloy, the hardness, yield strength and elongation were examined by tensile test. 1. The strength of deformed austenite in Fe-30%Ni-0.35%C alloy was increased due to the work hardening induced from the dislocation density increased during deformation. The strength of ausformed martensite was increased because of defects inherited from deformed austenite by martensitic transformation. 2. The ductility of ausformed martensite was shown a nearly constant values independent of deformation degrees because of the interaction of multiple factors such as increased retained austenite, formation of void and decrement of twin in ausformed martensite. 3. The strength of ausformed martensite by tempering treatment was shown a little decrement up to $340^{\circ}C$, especially showed remarkable softening resistance in higher deformation degrees. 4. Virgin martensite and ausformed martensite were shown a maximum yield strength by clustering in tempering at $100^{\circ}C$ and above $100^{\circ}C$, yield strength was very small decreased due to the decrement of solute carbon by the destruction of clustering. 5. The decomposition of retained austenite was not shown up to $450^{\circ}C$ in ausformed martensite with tempering treatment, and the matrix was rapidly softening because of the decomposition of martensite and the formation of reversed austenite with tempering above $400^{\circ}C$.

• 열처리공학회지
• /
• 제17권3호
• /
• pp.151-164
• /
• 2004

The changes of microstructural and mechanical properties were evaluated for the high burn-up fuel claddings after the neutron irradiation of $1.8{\sim}3.1{\times}10^{20}n/cm^2$ (E>1.0 MEV) in HANARO research reactor. After the irradiation, the spot-type dislocations (a-type dislocations) were easily observed in most claddings, and the density of the dislocations was different depending on the grains and was higher at grain boundaries than within grains. As the final annealing temperature increased, the density of spot-type dislocations increased and the line-type dislocations (c-type dislocations) which was perpendicular to the <0002> direction, appeared sporadically in some claddings. However, the types of precipitates in the fuel claddings after the irradiation were not changed from that in unirradiated claddings. The mechanical properties including the hardness, strength and elongation after the irradiation were changed due to the formation of spot-type dislocations. That is, the increase in hardness and strength as well as the decrease in elongation after the irradiation was occurred simultaneously with increasing the final annealing temperature. Owing to the Nb contribution to the formation of spot-type dislocation during the irradiation, the increase in hardness and strength in higher Nb-contained Zr alloys after the irradiation was higher than that in lower Nb-contained Zr alloys.

• 열처리공학회지
• /
• 제4권4호
• /
• pp.15-23
• /
• 1991

The damping capacities of the nonthermoelastic bcc type lath martensite and of the nonthermoelastic hcp type thin plate martensite in Fe-Mn alloys were studied. Fe-17%Mn alloy showing the hcp type thin plate martensite was superior to Fe-4%Mn alloy having the bcc type lath martensite in damping capacity. The damping capacity of the Fe-17%Mn alloy became greater with increasing the hcp martensite volume fraction. The damping mechanism of the Fe-4%Mn alloy was well explained by the dislocation model. However, the damping mechanism of the Fe-17%Mn alloy was explained on the basis of austenite/martensite interface moving model. The two alloys showed almost same levels of tensile strength. However, the elongation was greater in the Fe-17%Mn alloy than in the Fe-4%Mn alloy, showing lower yield strength in the former than in the latter. This result was considered to be attributed to formation of stress-induced martensite during tension test.

• 한국지구과학회지
• /
• 제33권5호
• /
• pp.434-449
• /
• 2012

The Mesozoic leucocratic granite in the northeastern margin of the Taebaeksan Basin was transformed to protomylonite and mylonite. Mylonitic foliations generally strike to NWWNW and dip to NE with the development of a sinistral strike-slip (top-to-the-northwest) shear sense. Grain-size reduction of feldspar in the mylonitized leucocratic granite occurred due to fracturing, myrmekite formation and neocrystallization of albitic plagioclase along the shear fractures of K-feldspar porphyroclasts. As the deformation proceeded, compositional layering consisting of feldspar-, quartz- and/or muscovite-rich layers developed in the mylonite. In the feldspar-rich layer, fine-grained albitic plagioclase and interstitial K-feldspar were deformed dominantly by granular flow. On the other hand, quartz-rich layers containing core-mantle and quartz ribbons structures were deformed by dislocation creep. Based on calculations from conventional two-feldspar and ternary feldspar geothermometers, mylonitization temperatures of the leucocratic granite range from 360 to $450^{\circ}C$. It thus indicates that the mylonitization has occurred under greenschist-facies conditions. Based on the geochemical features and previous chronological data, the leucocratic granite was emplaced during the Middle Jurassic at volcanic arc setting associated with crustal thickening. And then the mylonitization of the granite occurred during the late Middle to Late Jurassic (150-165 Ma). Therefore, the mylonitization of the Jurassic granitoids in the Taebaeksan Basin was closely related to the development of the Honam shear zone.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• 한국결정성장학회지
• /
• 제9권4호
• /
• pp.402-416
• /
• 1999

The thermal distributions near the growth interface of 150nm CZ crystals were measured by three thermocouples installed at the center, middle (half radius) and edge (10nm from surface) of the crystals. The results show that larger growth rates produced smaller thermal gradients. This contradicts the widely used heat flux balance equation. Using this fact, it is confirmed in CZ crystals that the type of point defects created is determined by the value of the thermal gradient(G) near the interface during growth, as already reported for FZ crystals. Although depending on the growth systems the effective length of the thermal gradient for defect generation are varied, we defined the effective length as 10n,\m from th interface in this experiment. If the G is roughly smaller than 20C/cm, vacancy rich CZ crystals are produced. If G is larger than 25C/cm, the species of point defects changes dramatically from vacancies to interstitials. The experimental results after detaching FZ and CZ crystals from the melt show that growth interfaces are filled with vacancies. We propose that large G produces shrunk lattice spacing and in order to relax such lattice excess interstitials are necessary. Such interstitials recombine with vacancies which were generated at the growth interface, nest occupy interstitial sites and residuals aggregate themselves to make stacking faults and dislocation loops during cooling. The shape of the growth interface is also determined by te distributions of G across the interface. That is, the small G and the large G in the center induce concave and convex interfaces to the melts, respectively.

• 치과방사선
• /
• 제28권1호
• /
• pp.285-297
• /
• 1998

This report details a case of 8-year-old girl showing failure of odontogenesis after chemo-radiation therapy for the rhabdomyosarcoma at the age of 4. The observed results were as follows : 1. Past history revealed that she had received for a total radiation dose of 4430cGy, 29 fractions in 6 weeks and chemotherapy with vincristine, actinomycin D and cytoxan, followed as maintenance phase for 2 years. 2. The patient was symptom -free and appointed for the treatment of multiple dental caries. 3. Oral examination showed hypoplastic enamel on whole erupted permanent teeth and showed retarded eruption. 4. Conventional radiograms showed failure of root development including abrupt cessation of root formation and root agenesis, and microdontia, missing teeth, irregular enamel, dislocation of the impacted teeth. Additional finding showed good healing bone pattern on the left mandibular ramus and angle area. 5. Cephalometric analysis revealed failure of bite raising due to incomplete eruption of all the first molars and made it possible to suspect entrapped mandibular growth and then Class II tendency growth. 6. There was correlation between the time of chemo-radiation therapy and the damage of the teeth.

• 한국결정성장학회지
• /
• 제2권2호
• /
• pp.77-82
• /
• 1992

FZ법에 의한 결정성장에 있어서 용융대는 고액 계면의 장력에 의해 유지되고 상.하부의 고체봉 사이에 위치하고 있다. 따라서, 용융대의 표면에서는 온도와 농도 차이에 의해 표면장력의 구배가 발생하고 있는 marangoni 대류의 구동력으로 작용한다. 본 연구에서 정상상태의 결정성장시는 결정의 가장자리 영역에서의 Solute 농도는 결정내부 보다도 높아지게 되고 전위의 분포도 불규칙하여 지며, void나 기포 침투, Secondary phase의 생성 및 미소균열등의 결함 발생 확률이 계면부근에서 높아지는 결과를 알 수 있었다. 이는 고액성장 계면이 marangoni 대류에 의하여 이 영역에서 온도의 국부적인 변동에 의해 불규칙하여 지게 되기 때문이라 사료된다.

• 한국분말재료학회지
• /
• 제17권6호
• /
• pp.477-481
• /
• 2010

Cu-Sn based alloys were manufactured by gas atomization spray casting route in order to achieve a fine scale microstructure and a high tensile strength. The spray cast Cu-10Sn-2Ni-0.2Si alloy had an equiaxed grain microstructure, with no formation of brittle ${\delta}-Cu_{41}Sn_{11}$ phase. Aging treatment promoted the precipitation of finely distributed particles corresponding to ${\delta}-Ni_2Si$ intermetallic phase throughout the $\alpha$-(CuSn) matrix. The cold-rolled Cu-Sn-Ni-Si alloy had a very high tensile strength of 1200 MPa and an elongation of 5%. Subsequent aging treatment at $450^{\circ}C$ for 1h slightly reduced the tensile strength to 700 MPa and remarkably increased the elongation up to 30%. This result has been explained by coarsening the precipitates due to over aging and reducing the dislocation density due to annealing effects.

• Applied Microscopy
• /
• 제45권3호
• /
• pp.170-176
• /
• 2015

In this work, various electron microscopy and analysis techniques were used to investigate the microstructural evolution of a 9% Cr tempered martensite ferritic (TMF) steel T91 upon ultrasonic nanocrystalline surface modification (UNSM) treatment. The micro-dimpled surface was analyzed by scanning electron microscopy. The characteristics of plastic deformation and gradient microstructure of the UNSM treated specimens were clearly revealed by crystal orientation mapping of electron backscatter diffraction (EBSD), with flexible use of the inverse pole figure, image quality, and grain boundary misorientation images. Transmission electron microscope (TEM) observation of the specimens at different depths showed the formation of dislocations, dense dislocation walls, subgrains, and grains in the lower, middle, upper, and top layers of the treated specimens. Refinement of the $M_{23}C_6$ precipitates was also observed, the size and the number density of which were found to decrease as depth from the top surface decreased. The complex microstructure and microstructural evolution of the TMF steel samples upon the UNSM treatment were well-characterized by combined use of EBSD and TEM techniques.