• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.585-588
• /
• 2007

We studied the effect of self-erase discharge on the luminous efficacy of ac PDPs. We observed through discharge current analysis to confirm that the selferase discharge occurred mainly between sustain cathode and address electrode, which have an influence on the luminous efficacy. The amount and timing of the self-erase discharge was varied to observe its effect on the luminous efficacy. It has been found that the luminous efficacy could be improved by the self-erase discharge when it is adjusted to occur right before the main discharge in the small gap structure. In the long gap structure, on the contrary, the luminous efficacy could be increased when the self-erase discharge is suppressed. Also, various waveforms to control self-erase discharge are suggested and tested in the panel experiments.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.161-161
• /
• 2011

The design methodology of the sluice caisson structure is one of important factor that is closely related to the efficiency in tidal power generation. When the sluice caisson is designed to maximize the water discharge capability, it is possible to minimize the number of sluice caissons for attaining the water amount required for achieving the target power generation, which results in reduction of the construction cost for the sluice caisson structure. The discharge capability of sluice caisson is dependent on the geometrical conditions of an apron structure which is placed in both sides of the sluice caisson. In this study, we investigated numerically the variation of water discharge capability of sluice caisson according to the geometrical conditions of apron. Flow fields are simulated with FLOW-3D software using VOF method.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1581-1583
• /
• 2000

In this paper, we proposed a surface discharge FFL with the new electrode structure like the needle shaped electrode as the variation of cell structure to high luminance and low power consumption. In comparison with different electrode structure it has low discharge voltage and current and good optical characteristics. So it has better discharge characteristics than different surface discharge FFL and can be fungible of backlight as a lighting source in LCDs.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.633-640
• /
• 2007

In this paper, 3-D reciprocating compressor is taken into flow-structure interaction analysis. The full cycle process consisted of cylinder expansion and compression has been modeled without considering flow leakage through cylinder wall. Fully-coupled FSI analysis of this compressor model was iteratively solved and gives sufficient result with the experimental test. The study is emphasized to thoroughly investigate discharge valve motion, opening and closing, in order to determine discharge valve region which is prone to have high effective stress. The cylinder pressure is successfully validated before conducting impact analyses between discharge valve and other susceptible supported structure. Velocity profile has been obtained in FSI analysis is used as initial condition to carry out further impact analyses. Stress result of discharge valve and valve spring gives preliminary estimation of higher stress area due to its impact phenomena.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.179-184
• /
• 2014

The discharge characteristics of an open dielectric structure were investigated, especially such as a firing voltage and related wall voltage, compared with conventional panel structure based on the Vt close curve measurement in AC plasma display panel. While the front panel of the conventional structure in AC plasma display panel was composed of the glass, electrodes, and dielectric, the open dielectric structure could easily produce the discharge between the scan and the sustain electrodes by erasing the dielectric layer between two electrodes. As the open dielectric structure differ from the conventional structure, various problems were produced when driving with the conventional driving waveform. Especially, due to the changes in the discharge firing characteristics of the open dielectric structure between the scan and the sustain electrodes on the front panel, the conventional reset waveform including the address waveform needed to be modified. In this study, the Vt close curves were measured to compare the discharge firing voltages on three electrodes in the conventional and open dielectric structure and based on the Vt close curve analysis, the modified driving waveform suitable for the open dielectric structure was proposed.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1749-1751
• /
• 1997

AC PDP with surface micro discharge has a structure that all discharge electrodes are arranged on the front glass panel, and the rear glass panel merely serves as a cover glass to form the micro discharge space. The relationships between the dischage voltage and the structure among such as electrode width, distance between electrodes, discharge space gap, and dielectric layer width are investigated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.5
• /
• pp.732-738
• /
• 2015

In ac discharge, emission efficiency shows an time-varying characteristics during discharge. The phenomenon is caused by the potential distribution changes during the discharge, which indicates that a specific potential distribution can contribute to a high improvement of the emission efficiency. To create an artificial environment for a potential distribution favorable to emission efficiency, we used the asymmetric electrode structure and proved the capability. Our results showed that the ratio of the area of anode to cathode became larger, the emission efficacy was greatly improved.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2286-2292
• /
• 2011

In this paper we present the design of Low Noise Amplifier(LNA), mixer and filter for RF front-end part of partial discharge monitoring system. The monitoring system of partial discharge in high voltage power machinery is used to prevent many kinds of industrial accidents, and is usually composed of three parts - sensor, RF front-end and digital microcontroller unit. In our study, LNA, mixer and filter are key components of the RF front-end. The LNA consists of common gate and common source-cascaded structure and uses the resistive feedback for broad band matching. A coupled line structure is utilized to implement the filter, of which size is reduced by the meander structure. The mixer is designed using dual gate structure for high isolation between RF and local oscillator signal.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1786-1788
• /
• 1999

In this paper, we studied Surface Discharge Type Flat Fluorescent Lamp with High Luminance for LCD Backlighting, Liquid Crystal display(LCDs) demand the use of fluorescent lamp as the backlighting source. This lamp is Surface Discharge Type structure with a pair of Sodalime glass, insulator layer, phosphor layer, and Xe gas gap. In spite of its simple structure, the lamp has uniform and stable discharge over entire volume. Till now, we measured the current-voltage(V-I), Firing Voltage, Sustain Voltage for 0.5mm, 1mm electrode gap. In experiment result, long gap cell structure cause high firing voltage. The rising in firing voltage in long gap structure could not be explained by paschen's law because of non-uniform electric field.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.600-603
• /
• 2000

Recently, Display devices have become important in the information-oriented society and flat display devices are greatly demanded. Liquid crystal display(LCD) represents one of the most promising devices for large size desk-top monitors, notebook PC and car navigation system. However LCD cannot give forth light itself and must have backlight system. The most popular backlighting system is composed of a lighting-guide plate and CCFL as a lighting source. The number of CCFL must increase up if the area of display is increased. So a new backlighting source with high luminance is needed for large LCDs. In this paper, we proposed a surface discharge FFL with the new electrode structure like the needle shaped electrode as the variation of cell structure to high luminance and low power consumption. In comparison with different electrode structure it has low discharge voltage and current and good optical characteristics. So it has better discharge characteristics than different surface discharge FFL and can be fungible for a backlight as a lighting source in LCDs.