• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.15-23
• /
• 2000

In the present study, flow characteristics of turbulent pulsating flow in the square-sectional $180^{\circ}$curved duct are investigated experimentally. In order to measure axial direction velocity and secondary flow distributions, experimental studies for air flow are conducted in the square-sectional $180^{\circ}$curved duct by using the LDV system with the data acquisition and the processing system of the Rotating Machinery Resolver (RMR) and the PHASE software. The experiment is conducted on seven sections form the inlet($\phi=0^{\circ}$) to the outlet($\phi=180^{\circ}$) at $30^{\circ}$intervals of the duct. The results obtained from the experimentation are summarized as follows : In the axial direction velocity distributions of turbulent pulsating flow, when the ratio of velocity amplitude (A1) is less than one, there is hardly any velocity change in the section except near the wall and in axial velocity distribution along the phase. The secondary flow of turbulent pulsating flow has a positive value at the bend angle of $150^{\circ}$regardless of the ratio of velocity amplitude. The dimensionless value of secondary flow becomes gradually weak and approaches zero in the region of bend angle $180^{\circ}$without regard to the ratio of velocity amplitude.

• Proceedings of the Korea Contents Association Conference
• /
• 2005.11a
• /
• pp.548-551
• /
• 2005

In this paper, three axial accelerometer was used to develop a small sensor module, which was attached to human body to calculate the acceleration in gravity direction by human motion, when it was positioned in any direction. To measure its wearer's walking or running motion using the sensor module, the acquired sensor data was pre-processed to enable its quantitative analysis. The acquired digital data was transformed to orthogonal coordinate value in three dimension and calculated to be single scalar acceleration data in gravity direction and normalized to be physical unit value.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.6
• /
• pp.484-493
• /
• 2013

Typical underwater acoustic sensors can measure the scalar quantity of sound-pressure-magnitude with the limitation of being unable to identify the direction of an incoming wave. This paper proposes a method to detect the direction of the sound wave with a ring sensor. The sensor of the proposed structure has a piezoceramic ring divided into eight elements, and distinguishes the direction of the sound wave by properly combining the output voltages of the piezoceramic elements. Further, through the analysis of the effects of the structural parameters like the ring radius and length, and piezoceramic thickness, we have suggested the way to improve the sensitivity of the vector sensor.

• Journal of Biosystems Engineering
• /
• v.25 no.2
• /
• pp.131-140
• /
• 2000

Spraying operation is one of the most essential in an orchard management and it is also hazardous to human body. for automatic and unmanned spraying , an autonomous travelling vehicle is demanded. In this study, a telemeter was developed using infrared beam which could detect trunks and obstacles measure distance and direction from the vehicle travelling in the orchard. The telemeter system was composed of two infrared LED transmitters and receivers, a beam scanning device for continuous object detection , two rotary encoders for angle detector, and a beam level controller for uneven soil surface. The detected distance and direction signal s were sent to personal computer which made for the system display the angular and distance measurements through I/O board. According to a field test in an apple farm, the system detected up to 10m distance under 12 V of transmitted beam intensity, however, it was recommended that the proper beam transmit intensity be 7 v at the 10 m distance, because of the negative effect to human body at 12 V. The error rate of this system was 0.92 % when the actual distance was compared to measured one. The system was feasible at the small error rate. The developed telemeter system was an important part for autonomous travelling vehicle provided the real time object recognition . A direction control system could be constructed suing the system. It is expected that the system could greatly contribute to the development of autonomous farm vehicle.

• Journal of Magnetics
• /
• v.18 no.4
• /
• pp.422-427
• /
• 2013

The aim of this study was to investigate effects of the number of acquisitions (NEX) on signal-to-noise (SNR) and artifacts in SENSE parallel imaging of magnetic resonance imaging (MRI). 3.0T MR System, 8 Channel sensitivity encoding (SENSE) head coils were used along with an in-vivo phantom. Reference sequence of 3D fast field echo (FFE) was consisted of NEX values of 2, 4, 6, 8, 10 and 12. The T2 turbo spin echo (TSE) sequence used for exams achieved SENSE factors of 1.2, 1.5, 1.8, 2.0, 2.2, 2.5, 2.8, 3.0, 3.2, 3.5, 3.8 and 4.0. Exams were conducted five times for each SENSE factor to measure signal intensity of the object, the posterior phase-encode direction and frequency direction. And SNR was calculated using mean values. SENSE artifacts were identified as background signal intensity in the phase-encoded direction using MRIcro. It was found that SNR increased but SENSE artifacts reduced with NEX of 4, 8 and 12 when the NEX increased in reference scan. It is therefore concluded that image quality can be improved with NEX of 4, 8 and 12 for reference scanning.

• Journal of Information Technology Services
• /
• v.10 no.1
• /
• pp.65-72
• /
• 2011

In this paper, we consist of three dimensional acceleration sensor as a small-sized sensor module to acquire base technologies that need to estimate exhibition audience' moving distance. and that we developed algorism and device that can calculate acceleration in gravity direction with attaching it to people's body part without regard to three dimensional direction. By making use of the sensor module, we have to process the data that let it quantitatively process possible to measure people's walk and movement by computer system. We normalized sensor output data in the process of change from sensor module to acquisition of data, rectangular coordinates and single scalar acceleration value in gravity direction. Printed out sensor data attaching sensor module to people's body part is used for motion pattern detection after normalization, Motion sensor devised mode change algorism because it print data of other pattern according to attached position of body. For algorism design, we collected data occurring during walking about subject and we also defined occurring problem domain after analyzing the data. We settle defined problem domain and that we simulated the walking number measuring instrument with highly efficient in restricted environment.

• Journal of Sensor Science and Technology
• /
• v.22 no.4
• /
• pp.292-296
• /
• 2013

The ultrasonic wind sensor that pass through the air, beating the delivery of ultrasonic wind speed increases or decreases by the physical characteristics of the wind speed and the direction of the sensor, the transmission and reception of ultrasonic time difference measured by a two-axis vector wind and wind speed measured by calculating a device that converts the digital signal is Anemometer and wind direction meteorological facilities management, management of the ship sail used for various purposes, including, but used the existing 3-cup (mechanical) anemometer wind rotor caused by mechanical wear parts replacement due to the short-term, the reliability of the product is low, parts replacement, and according to the characteristics caused the car, there is a problem in high maintenance costs. In addition, because the bearings use of the marine environment and the cryogenic environment was constrained. In this study, the excellent long-term reliability, using ultrasonic-type environment that is not constrained to produce wind anemometer located $90^{\circ}$ conformal road using four piezoelectric sensors were fabricated structures, the piezoelectric oscillator circuit produces a rash and receiving transmit and receive speeds the car through the two-axis vector calculation to measure wind velocity processor firmware programming, and its characteristics were tested.

• Structural Monitoring and Maintenance
• /
• v.10 no.2
• /
• pp.155-174
• /
• 2023

High performance concrete (HPC) has been extensively used in thin overlay for repair purpose due to its excellent strength and durability. This paper presents an experiment, where the sensor-instrumented HPC overlays have been followed by dynamic strain and moisture content monitoring for 1 year, under normal traffic. The vibrating wire and soil moisture sensors were embedded in overlay before construction. Four given HPC mixes (2 original mixes and their shrinkage-modified mixes) were used for overlays to contrast the strain and moisture results. A calibration method to accurately measure the moisture content for a given concrete mixture using soil moisture sensor was established. The monitoring results indicated that the modified mixes performed much better than the original mixes in shrinkage cracking control. Weather condition and concrete maturity at early age greatly affected the strain in concrete. The strain in HPC overlay was primarily in longitudinal direction, leading to transverse cracks. Additionally, the most moisture loss in concrete occurred at early age. Its rate was very dependent on weather. After one year, cracking survey was carried out by vision to verify the strain direction and no cracks observed in shrinkage modified mixes.

• Korea Trade Review
• /
• v.47 no.5
• /
• pp.321-336
• /
• 2022

The purpose of this study aims to investigate how consumer awareness and purchasing behavior are affected by the type of animosity against the nation. This study classified animosity into three categories: sociocultural, economic, and war-based. Additionally, the consumer's cognition toward animosity was split into two categories-empathic concernt and personal distress-and the direction of consumption behavior was split into two categories-individual brand avoidance behavior and collective bandwagon behavior. The concept of Fear of Missing Out (FoMO) was introduced for the direction of consumption behavior, further validating the moderating impact. Structural equation modeling method was used to measure the general consumption behvior of Korean consumers' animosity. The results were analyzed using a total of 279 samples. As a result, animosity motivated by war and by economics had a substantial impact on empathic concern, while animosity motivated by socioculture had a significant impact on personal distress. Personal distress had a good impact on an individual's brand antipathy behavior, which in turn led to brand dislike and avoidance. Empathic concern also had a positive impact on the phenomena of group sympathy, which leads to identification of conduct and social conformity. Also, it was proven that the group that had a high level of FoMO reacted strongly to the phenomenon of group collective behavior.

• The Mathematical Education
• /
• v.48 no.4
• /
• pp.399-417
• /
• 2009

The purpose of this study was to explore the adaptability of U.S. multiple-choice items to measure Mathematical Knowledge for Teaching (MKT) in Korea. For this purpose, the authors selected the number and operations form B which was developed by Learning Mathematics for Teaching (LMT) project at the University of Michigan and then adapted items in terms of general cultural context, school cultural context, mathematical substances, and language in Korea. The survey was administrated to 77 Korean in-service teachers who had more than three years of teaching experiences. Based on the survey, the authors compared the data to that of U.S. teachers who had participated California's Mathematics Professional Development Institute. As a result, the survey measures less knowledge Korean teachers than more knowledgable Korean teachers and there are strong correlations of relative item difficulties between Korean teachers and U.S. teachers for both Content Knowledge (CK) items and Knowledge of Content and Students (KCS) items. This study implies the future direction for developing items to measure teacher knowledge as well as designing effective teacher education programs.