• 반도체디스플레이기술학회지
• /
• 제18권2호
• /
• pp.58-62
• /
• 2019

Diffractive Optical Elements(DOEs) diffracts incident light using the diffraction phenomenon of light to generate a desired diffraction image. In recent years, the use of diffraction optics, which can replace existing refractive optical elements with flat plates, has been increased by implementing various optical functions that could not be implemented in refractive optical devices and by becoming miniaturized and compacted optical elements. Direct laser lithography is typically used to effectively fabrication such a diffractive optical element in a large area with a low process cost. In this study, the process conditions for fabricating patterns of diffractive optical elements in various shapes were found using direct laser lithographic system, and optical performance evaluation was performed through fabrication.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3467-3472
• /
• 2007

The effects of the wall geometry on the spray-wall impingement process of a hollow-cone fuel spray emerging from a high-pressure swirl injector of the Gasoline Direct Injection (GDI) engine were investigated by means of a numerical method. The ized Instability Sheet Atomization (LISA) & Aerodynamically Progressed Taylor Analogy Breakup (APTAB) model for spray atomization process and the Gosman model were applied to model the atomization and wall impingement process of the spray. The calculation results of spray characteristics, such as a spray development process and a radial distance after wall impingement, compared with the experimental ones by the Laser Induced Exciplex Fluorescence (LIEF) technique. It was found that the radial distance of the cavity angle of 90$^{circ]$ after wall impingement was the shortest and the ring shaped vortex was generated near the wall after spray-wall impingement process.

• 한국지리정보학회지
• /
• 제8권1호
• /
• pp.88-95
• /
• 2005

다중센서 결합에 의한 외부표정요소 결정기법은 항공기에 탑재한 GPS와 INS로 센서의 위치와 회전각을 정확히 결정함으로써 외부표정요소 결정을 위한 지상기준점 측량을 생략하거나 또는 최소한의 기준점만을 사용하여 외부표정요소를 결정할 수 있으며, 이에 따라 지형도 제작에 대한 시간과 경비를 크게 절감할 수 있다. 따라서 본 연구에서는 다중센서 결합과 동시에 CCD 카메라를 탑재하여 동시에 측량을 하고, 외부표정요소 직접결정 기법에 의한 CCD 영상으로 수치정사영상을 제작하였다. 본 연구에서 제작된 결과물에 대한 정확도 검증을 위하여 GPS로 측량한 지상검사점을 기본으로 하여 외부표정요소 직접결정 기법에 의하여 제작된 수치정사영상의 위치 정확도를 평가하였다. 수치정사영상은 소수의 기준점을 사용한 경우와 기준점을 사용하지 않은 경우의 두 가지로 제작하였다. 다중센서에 의한 제작된 수치정사영상의 정확도는 소수의 기준점을 사용한 경우, 축척 1:1,000 지도의 정확도 기준을 만족시켰으며, 기준점이 없이 제작된 정사영상의 정확도는 축척 1:5,000 지도의 정확도 기준을 만족함을 알 수 있었다.

• 한국염색가공학회지
• /
• 제18권6호
• /
• pp.69-79
• /
• 2006

The washing characteristics of steam jet heating process have been compared with other washing processes, such as low temperature process(standard process, below $40^{\circ}C$) and high temperature process(boiling process, up to $95^{\circ}C$) with the standard soil fabric, EPMA 105. Steam jet heating process showed almost the same washing efficiency as high maximum temperature process for pig's blood and wine. This result can be explained with the higher surface temperature of washing materials in steam jet process compared with direct boiling process. In terms of the energy and water consumption, the steam jet washing process showed significant savings compared with direct boiling type washing process.

• 한국염색가공학회지
• /
• 제33권4호
• /
• pp.210-219
• /
• 2021

It was intended to conduct basic research to reduce development lead time and cost consumed in DTP process technology development. For the simulation of HTPE fabric, virtual engineering software was used to generate fiber model, yarn model, fabric model, and finite element model of HTPE fiber. The purpose of this study is to analyze the correlation and error rate between the stiffness numerical analysis results according to the direct DTP process parameters using reactive dyes in the generated finite element model and the stiffness measurements of the actual sample ac- cording to ASTM D1388. And, after dyeing the HTPE plain fabric according to the direct DTP process parameters, we want to analyze the dyeability of the HTPE fabric fabrics according to the direct DTP process parameters through the color fastness analysis. When looking at the results of the analysis of the finite element model, a higher value was shown when the distance between the nozzle and the fabric was 3mm than when the distance was 10mm. When the distance between the nozzle and the fabric was 10mm and 7mm, the reactive dye did not penetrate sufficiently, resulting in poor clarity when viewed with the naked eye.

• 한국정밀공학회지
• /
• 제33권11호
• /
• pp.951-959
• /
• 2016

The aim of this paper is to investigate the improvement of surface characteristics of Stellite21 deposited layer by powder feeding type of direct energy deposition (DED) process using a plasma electron beam. Re-melting experiments of the deposited specimen is performed using a three-dimensional finishing system with a plasma electron beam. The acceleration voltage and the travel speed of the electron beam are chosen as process parameters. The effects of the process parameters on the surface roughness and the hardness of the re-melted region are examined. The formation of the re-melted region is observed using an optical microscope. Results of these experiments revealed that the re-melting process using a plasma electron beam can greatly improve the surface qualities of the Stellite21 deposited layer by the DED process.

• 소성∙가공
• /
• 제22권6호
• /
• pp.334-339
• /
• 2013

Direct Laser Melting is a prototyping process whereby a 3-D part is built layer wise by melting the metal powder with laser scanning. This process is strongly influenced by the shielding gas and the laser operating parameters such as laser power, scan rate, layering thickness, and rescanning. The shielding gas is especially important in affecting the microstructure and mechanical properties. In the current study, fabrication experiments were conducted in order to analyze the effect of shielding gas on the forming characteristics of direct laser melting. Cylindrical parts were produced from a Fe-Ni-Cr powder with a 200W fiber laser. Surface quality, porosity and hardness as a function of the layering thickness and shield gas were evaluated. By decreasing the layering thickness, the surface quality improved and porosity decreased. The selection of which shield gas, Ar or $N_2$, to obtain better surface quality, lower porosity, and higher hardness was examined. The formability and mechanical properties with a $N_2$ atmosphere are better than those parts formed under an Ar atmosphere.

• 한국의류학회지
• /
• 제33권1호
• /
• pp.139-148
• /
• 2009

In this study, we tried to verify the effectiveness of 3D scans of clothed participants from 20 to 24 year old men in fit analysis process. Carrying out fit analysis, we used 3D scan data and direct fit evaluation with the basic garments made as semi-fitted bodice pattern for men. The result of fit evaluation through 3D scan data showed the expert rated fitting items more positive than direct fit evaluation. Even though, generally there was a no significant difference in the response between 3D and direct fit analysis. Only there was a significant difference in the response to the specific place such as the center front line, neckline, shoulder seam, and etc. There was a no significant difference between the result of 3D scan and direct fit evaluation in the subjects' group. Also the result of assessment of 3D targeting consumers showed very positive and interested in using 3D scans for fit analysis. The ability to rotate the 3D scans for a variety of views proved to be a very effective process to analyze fit. Moreover, digital data is easily accessed at any locations and any time. Fit analysis using 3D scans could be great tool for not only fit evaluation in research but also better fitting in apparel industry.

• 산업기술연구
• /
• 제25권B호
• /
• pp.121-126
• /
• 2005

Micro wires manufactured by the straightening process are used in the BT(Bio-Technology), IT(Information-Technology), NT(Nano-Technology). We have developed a novel wire straightener which uses the direct heating method(DHM) for straightening the micro wire and shearing device for burr-less cutting. In this study, we confirm the tendency of micro wire after the shearing process. It is impossible to remove the burr in the shearing process. However, the embodiment of minimum burr size after the shearing process is the best in-process method. In order to minimize the burr size, we have accomplished the various experiment condition such as the U-groove, the effect of the counter punch, the shear angle, clearance.

• Transactions on Electrical and Electronic Materials
• /
• 제3권1호
• /
• pp.42-45
• /
• 2002

Properties of lead zirconate titanate ferroelectric thin films prepared by rapid thermal annealing/direct insertion thermal annealing were investigated. The remnant polarization (Pr), saturation polarization (Ps), and coercive force (Ec) of typical samples annealed by rapid thermal annealing (RTA) are about 13.7 $\mu$ C/cm$^2$, 27.1 $\mu$C/cm$^2$, and 55.6 kV/cm, respectively. The dielectric constant of the sample is about 786, the dielectric loss tangent is about 2.4% at 1 kHz. Furthermore, ferroelectric, conduction, and piezoelectric properties of the thin films annealed by RTA process and the direct insertion thermal annealing (DITA) process were compared. The influence of temperature in the dry process on the above properties was also investigated.