• Korean Journal of Remote Sensing
• /
• v.28 no.3
• /
• pp.307-318
• /
• 2012

To understand forest structures, the Geoscience Laser Altimeter System (GLAS) instrument have been employed to measure and monitor forest canopy with feasibility of acquiring three dimensional canopy structure information. This study tried to examine the potential of GLAS dataset in measuring forest canopy structures, particularly maximum canopy height estimation. To estimate maximum canopy height using feasible GLAS dataset, we simply used difference between signal start and ground peak derived from Gaussian decomposition method. After estimation procedure, maximum canopy height was derived from airborne Light Detection and Ranging (LiDAR) data and it was applied to evaluate the accuracy of that of GLAS estimation. In addition, several influences, such as topographical and biophysical factors, were analyzed and discussed to explain error sources of direct maximum canopy height estimation using GLAS data. In the result of estimation using direct method, a root mean square error (RMSE) was estimated at 8.15 m. The estimation tended to be overestimated when comparing to derivations of airborne LiDAR. According to the result of error occurrences analysis, we need to consider these error sources, particularly terrain slope within GLAS footprint, and to apply statistical regression approach based on various parameters from a Gaussian decomposition for accurate and reliable maximum canopy height estimation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1207-1210
• /
• 2004

As many humans age, degenerative lumbar spinal stenosis (DLSS) becomes a major cause of lower limb discomfort and disability. By surgical treatment method of DLSS, the existing surgical treatment methods using internal fixation have showed degeneration changes of an adjacent vertebrae and loss of lumbar spine lordosis-kyphosis due to eliminating a motion. For solving the problems of internal fixation, a novel interspinous spacer has been developed to treat DLSS by surgical treatment method. In this study, we evaluated the biomechanical effects of the interspinous spacer on the kinematics of the porcine lumbar spine before and after insertion of the implant. For this purpose, a device that is capable of measuring 3-D motions were built based on direct linear transformation (DLT) algorithm written with MATLAB program. Results showed that in extension, a change of the mean angle between the intact and the implanted specimens at L4-L5 was 1.87 degree difference and the implant reduced the extension range of motion of the L4-L5 (p＆lt;0.05). But the range of motion in flexion, axial rotation and lateral bending at the adjacent segments was not statistically affected by the implant. In conclusion, we thought that interspinous spacer may have remedical value for DLSS by flexing human lumbar spine.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• Korean Journal of Microbiology
• /
• v.39 no.3
• /
• pp.181-186
• /
• 2003

This study was performed to analyze quantitatively the number of living bacteria in forest soil samples collected from Mt. Keryong using improved direct viable count (DVC) and plate count (PC) methods. The number of living bacteria by DVC comprised 18～44% of the total direct count (TDC), whereas the number of living bacteria by PC was less than 1% of TDC. These results showed that viable but non-culturable (VBNC) bacteria existed in the soil with high percentages. Besides, DVC was proved to make it possible to make a quantitative detection of the VBNC bacteria. On the other hand, upon measuring the value from the conventional nutrient broth (NB) and $10^{-2}$ folded diluted nutrient broth (DNB), the values from the DNB showed 5 to 10 times higher than those from the conventional NB medium. These results indicate that oligotrophic bacterial groups, which could multiply in the low nutrient broth, abundantly exist in the soil ecosystem. It would also be possible to apply this kind of method to other substrate to make a quantitative detection of soil bacterial groups.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.15 no.1
• /
• pp.70-75
• /
• 1991

Contact angle measuring device was developed in this laboratory using laser beam projec-tion. The new method allows for rapid and direct determination of stationary, advancing, and receding contact angles on both planar and nonplanar solid surfaces, including fibers with very small diameters. A narrow laser beam impinges on an edge of an interface of liquid and solid. This makes two projected laser beam lines upon and radiating from the center of a protractor scale on a tangent screen. Contact angle is measured by determining the difference in angle on the protractor scale between the two projected laser beam lines. Contact angles measured on Perspex-CQ using this instrument were in agreement with the literature. it was shown that this instrument provides a novel method for the facile and accurate measurement of contact angles.

• Journal of Korean Society of Forest Science
• /
• v.99 no.5
• /
• pp.682-685
• /
• 2010

Coring has been widely used to measure annual increment in temperate forest ecosystems. This method is attractive because cores can be taken in just one visit. However, the accuracy of this method has not been tested. We expected coring to be less accurate than band dendrometers because of the eccentricity of tree growth. We studied 41 trees at the Long Term Experimental Forest in Mt. Gyebang, which has been monitored with band dendrometers since 1996. We collected two tree cores from the south and north face of each tree, 10 cm below the growth band. Increment cores were measured to 0.01 mm under stereomicroscopy. Annual growth from 1997 to 2006 was 3.2 mm $yr^{-1}$ for Quercus mongolica, 3.5 mm $yr^{-1}$ for Kalopanax septemlobus, and 5.7 mm $yr^{-1}$ for Pinus densiflora. The difference between the two methods was 10% for Q. mongolica, 14% for K. septemlobus, and 4% for P. densiflora. Compaction in the corer and shrinkage during drying decreased diameter increment by 5.6% and 1.0% on P. densiflora, respectively. This study suggests that the two methods for annual increment measurement are very similar, but species specificity should be concerned for direct comparison.

• Journal of Radiation Protection and Research
• /
• v.10 no.1
• /
• pp.29-40
• /
• 1985

The objectives of present study is to investigate genetic damage of radiation in mammalian male germ cell and. to establish available screening method for determining genetic hazard by radiation. Several methods were employed to measure the genetic damage of radiation as follows: Sperm head counts, frequency occurrence of sperm with abnormal head shape, fertility, activity of LDH-X, and the induction of unscheduled DNA synthesis (U.D.S.) in male mouse were performed with the passing of time after irradiation by making use of the sequence of event that occurs during spermatogenesis. Sperm head counts and activity of LDH-X in testes were gradually reduced by increased radiation dose and with the passing of the time after irradiation. Frequency occurrence of sperm with abnormal head shape, sterile period, and the induction of unscheduled DNA synthesis were increased by increased radiation dose. It is suggested that since germ cell is a direct reflection of genetic complement, the use of male germ cell is rapid and convenient method for measuring genetic damage by radiation.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.44-50
• /
• 2003

If the accelerometers are used in measuring the response, the absolute values of the velocity and displacement are not usually obtainable because their initial values are not accounted for in the integration of the acceleration response. A new dynamic response conversion algorithm of both the time domain and the frequency domain is proposed for the problem in estimating the displacement data by defining the transformed responses. In this algorithm, the displacement response can be obtained from the measured acceleration records by integration without requiring the knowledge of the initial velocity and displacement information. The applicability of the technique is tested by an example problem using the real bridge's superstructure under several cases of moving load. In the response conversion procedure of the frequency domain, the identified response according to the frequency can be estimated by changing over the limits of integration. If the reliability of the identified responses is ensured, it is expected that the proposed method for estimating the impact factor can be useful in the bridge's dynamic test. This method can be useful in those practical cases when the direct measurement of the displacement is difficult as in the dynamic studies of huge structure.

• Korean Journal of Applied Biomechanics
• /
• v.28 no.1
• /
• pp.61-67
• /
• 2018

Objective: The human body is often modelled as a spring-mass system. Lower extremity stiffness has been considered to be one of key factor in the performance enhancement of running, jumping, and hopping involved sports activities. There are several different classification of lower extremity stiffness consisting of vertical stiffness, leg stiffness, joint stiffness, as well as muscle and tendon stiffness. The primary purpose of this paper was to review the literature and describe different stiffness models and discuss applications of stiffness models while engaging in sports activities. In addition, this paper provided a current update of the lower extremity literature as it investigates the relationships between lower extremity stiffness and both functional performance and injury. Summary: Because various methods for measuring lower extremity stiffness are existing, measurements should always be accompanied by a detailed description including type of stiffness, testing method and calculation method. Moreover, investigator should be cautious when comparing lower extremity stiffness from different methods. Some evidence highlights that optimal degree of lower extremity stiffness is required for successful athletic performance. However, the actual magnitude of stiffness required to optimize performance is relatively unexplored. Direct relationship between lower extremity stiffness and lower extremity injuries has not clearly been established yet. Overall, high stiffness is potentially associate risk factors of lower extremity injuries although some of the evidence is controversial. Prospective injures studies are necessary to confirm this relationship. Moreover, further biomechanical and physiological investigation is needed to identify the optimal regulation of the lower limb stiffness behavior and its impact on athletic performance and lower limb injuries.

• Analytical Science and Technology
• /
• v.20 no.1
• /
• pp.41-48
• /
• 2007

The determination method for the trace lead and cadmium in glass materials was developed by ICP-AES. The lead- and cadmium-DDTC chelates were formed by adding Na-DDTC (sodium diethyldithiocarbamate) as a chelating agent and extracted into MIBK (methyl-isobutyl ketone). Direct measuring of the trace lead and cadmium in glass was not possible because of the interferences of matrix elements as Na, Si, Mg and Ca of glasses unless solvent extraction of lead and cadmium was applied. This procedure was confirmed to be valid quantitative method of Pb and Cd analysis in glass did not influence of sample matrix, by applying it procedure to artifact sample and NIST SRM 1412.