• Economic and Environmental Geology
• /
• v.17 no.1
• /
• pp.49-55
• /
• 1984

This paper describes three-dimensional (3-D) standard curves for conductive dipping buried bodies in induced polarization (IP) method. Dipole-dipole IP responses for the dipping bodies are calculated by the numerical modeling technique using an integral equation solution. Dip angles of the bodies are 0, 20, 45, 70 and 90 degrees, respectively. The horizontal (0-degree dip) and vertical (90-degree dip) bodies produce symmetrical patterns of IP responses. The dipping bodies of 20, 45 and 70 degrees, however, produce asymmertical patterns, with the highest IP contours dipping in the direction opposite to the bodies in pseudo-sections. The most remarkable asymmetrical pattern appears in the model of 20-degree dip. It is difficult to distinguish the body of 70-degree dip from that of 90-degree dip on the basis of dipole-dipole IP data. The IP pattern in pseudo-sections varies when the line moves away from the center of the body along strike, with the anomaly deeper and smaller in amplitude. IP maps seem to be more useful than IP pseudo-sections in predicting the location of target.

• Food Science and Biotechnology
• /
• v.15 no.4
• /
• pp.529-533
• /
• 2006

To produce fresh-cut fruit products of high quality, the combined effects of postharvest calcium and heat treatment on Tsugaru apple were examined. Whole fruits were treated for 20 min at three different conditions: dipping in 3% $CaCl_2$ solution at $45^{\circ}C$ or ambient temperature, or in heated water at $45^{\circ}C$. The calcium content of the apples dipped in $CaCl_2$ solution at $45^{\circ}C$ was higher than that of the control and the non-heated calcium dipping. The fruits with calcium and heat treatment showed the same pattern of respiration rates as the control did during storage. The browning degree of the apple slices increased to approximately 3% after one-day storage, but no significant difference was observed between the treated and untreated apples. The fruits with $CaCl_2$ solution dipping at $45^{\circ}C$ had higher firmness than those with calcium dipping or heat treatment alone.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.354-359
• /
• 2006

Recently, the interest in lithography without photo exposure has been increased compare to the conventional photolithography in nano meter and micrometer size patterning area. We studied a self aligned dipping of Ag solution through micro contact printing (${\mu}-CP$) with octadecyltrichlorosilane (OTS) treated polydimethylsiloxane (PDMS) soft mold. The OTS monolayer on the patterned PDMS was formed by dipping it into OTS solution. We transferred the OTS monolayer from PDMS mold to the glass. The OTS monolayer changed the surface energy from hydrophilic surface to hydrophobic surface, And then we made self aligned Ag solution patterns just after dipping the substrate, using adhesion difference of Ag solution between OTS treated hydrophobic area and non-OTS treated hydrophilic area. We finally get the Ag patterns through only dip-coating after the ${\mu}-CP$ process. And we observed surface energies on the glass substrate through the contact angle measurements as time goes on.

• Korean Journal of Veterinary Research
• /
• v.44 no.1
• /
• pp.113-120
• /
• 2004

1% iodophor loaded microspheres of PLGA (Poly[DL-Lactide-co-Glycolide]) were prepared by solvent evaporation method and were applied to the cows on dry period for evaluating it's preventive effects on intramammary infections. The morphology of the microspheres were evaluated using scanning electron microscopy and their releasing patterns were investigated. On investigating idophor releasing patterns of the microsphere, burst releasing pattern was detected until 2 days after in vitro incubation and sustained releasing was observed until 4 weeks. In field trial of teat dipping solution containing idophor loaded microspheres in dry cows showed significant preventive effects of intramammary infection caused by S. aureus, S. agalactiae, coagulase negative Staphylococci and coliform bacteria (p<0.05).

• Journal of the Korea Society for Simulation
• /
• v.20 no.2
• /
• pp.59-66
• /
• 2011

In this paper, a method to allocate a submarine search mission to an ASW(Anti-Submarine Warfare) helicopter is proposed. The aim of the proposed method is to increase the submarine detection capability. For this purpose, we modeled the behaviors that the ASW helicopter conduct during the search mission, and the relations between the behaviors are also modeled. To measure quantitatively the effectiveness of ASW search mission, the measure of effectiveness(MOP) is defined. Scenarios are designed to analyze the effectiveness utilizing the ASW mission model. We conducted simulations applying the designed scenarios and some parameters concerned with the friendly ship and the enemy submarine interacting each other in the ASW missions. We analyzed the result of simulation depending on the dipping interval and the pattern of dipping positions in the situation that the helicopter operates for a long time and should resupply several times on the friendly ship. From the analyzed data, we suggested the practical value of ratio between the detectable range of the sonar and the dipping interval to improve the effectiveness of ASW mission.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.25.1-25.1
• /
• 2009

Pattern 웨이퍼 상의 오염입자 제거는 반도체 산업의 주된 과제 중 하나이다. Pattern의 선폭이 좁아짐에 따라 Pattern에 손상을 가하지 않고 오염입자를 제거 하는 것은 더욱 어려워지고 있다. 그뿐만 아니라 기존 습식세정 공정에서의 화학액에 의한 환경오염 및 박막의 손실도 문제가 되기 시작했다. 이러한 문제를 해결하기 위해 기존 세정공정에서 화학액의 농도를 낮추고 Megasonic 등을 이용하여 세정력을 보완하는 방법들이 연구되고 있다. 하지만 습식세정의 경우 강한 화학작용으로 인한 표면 손상 및 물 반점의 문제는 여전히 이슈가 되고 있다. 이러한 단점을 극복하기 위하여 건식 세정법이 제시되고 있으며 이 중 레이저 충격파는 레이저를 집속시켜 발생된 충격파를 이용하여 입자를 제거하기 때문에 국부적인 세정이 가능하며 세정력 조절이 가능하여 손상이 세정을 할 수 있다. 그러나 Pattern의 구조에 의해 전되는 세정력의 차이가 발생하고 Trench 내부의 오염입자제거 문제점이 발생할 수 있다. 시편은 Si STI Pattern을 100 nm PSL Particle (Red Fluorescence, Duke Scientific, USA) 을 50ppm 농도로 희석시킨 IPA에 dipping 하여 오염시킨 후 N2 Gas를 이용하여 건조하여 준비하였다. 그리고 레이저 충격파 세정 시스템은 최대 에너지 1.8 J까지 가능한 레이저를 발생하는 1,064 nm Nd:YAG 레이저를 이용하여 실험하였다. 레이져 충격파 실험은 충격파와 시편사이의 거리, gap distance와 에너지를 변환하여 세정효율을 관찰하였다. 세정효율은 세정 전후의 입자 감소량을 현광현미경 (LV-150, Nikon, Japan)를 이용하여 측정하였다. 그 결과, Trench 내부의 오염입자의 경우 Trench 밖의 오염입자에 비해 세정효율이 떨어지는 것으로 나타났으나 시편과 레이저 초점과의 거리가 가까워짐에 따라 Trench 내부의 오염입자에 대한 세정 효율을 증가시킬 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.687-687
• /
• 2013

In rearpoint contact solar cell and the PERC (passivated emitter rear contact) type cell, surfaces were passivated by SiO2 or Al2O3 to increase solar cell efficiency. Therefore, we have investigated the effect of surface passivation for crystalline silicon solarcell using mass-production atomic layer deposited (ALD) Al2O3. The patttern which consists of cylinders with 100um diameter and 5um height was formed by PR patterning on Si (100) substrate and then Al2O3 of about 10nm and 20nm thickness was deposited by ALD. The pattern in 10 nm Al2O3 film was removed by dipping in aceton solution for about 10 min but the pattern in 20 nm Al2O3 film was not. The influences of process temperature and heat treatment were investigated using microwave photoconductance decay (PCD) and Quasi-Steady-State photoconductance (QSSPC). The solar cell process used in this work combines the advantage of using the applicability of a selective deposition associated with a ALD passivation and the use of low-cost screen print for the contacts formation.

• Economic and Environmental Geology
• /
• v.32 no.2
• /
• pp.161-167
• /
• 1999

Electric and electromagnetic surveys were conducted to investigate the deep structure of the Ulsan fault in Ipsil area, south of Kyeongju. On this study, especially high-frequency magnetotelluric method of electromagnetic survey in the frequency range of 10~100,000 Hz was mainly employed to study the deep subsurface configuration. High-frequency MT survey was performed at 70 points of spacing 30~50 m, making 3.8 km survey line. As a survey result, a 2-km-depth 2-D cross-section was achieved. It shows vertical and horizontal subsurface variations of resistivity values. Near-surface layer having low resistivity value becomes thicker eastward up to 800m. There is a steep low resistivity zone in the west side of survey line, and there exists two low resistivity zones dipping west in the east side of survey line. Two low resistivity zones are interpreted to be related to major movement pattern of the Ulsan fault. This suggests that major fault lines are developed on both peripheral sides of the broad fault zone.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.987-991
• /
• 2009

We report growth of vertically well-aligned zinc oxide (ZnO) nanorods on indium-tin oxide (ITO)/glass substrates using a simple aqueous solution method at low temperature via control of the ZnO seed layer morphology. ZnO nanoparticles acting as seeds are pre-coated on ITO-coated glass substrates. by spin coating to control distribution and density of the ZnO seed nanoparticles. ZnO nanorods were synthesized on the seed-coated substrates in a dipping process into a main growth solution. It was found that the alignment of ZnO nanorods can be effectively manipulated by the spin-coating speed of the seed layer. A grazing incidence X-ray diffraction pattern shows that the ZnO seed layer prepared using the higher spin-coating speed is of uniform seed distribution and a flat surface, resulting in the vertical growth of ZnO nanorods aligned toward the [0001] direction in the main growth process.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.4
• /
• pp.50-53
• /
• 2023

In this study, the photolithography process was chosen to reduce the aspect ratio of the cross-section of a high-temperature superconducting (HTS) tape by dividing the superconducting layer of the tape. Reducing the aspect ratio decreases the magnetization losses in the second-generation HTS tapes generated by AC magnetic fields. The HTS tape used in the experiment has a thin silver (Ag) layer of about 2 ㎛ on top of the REBCO superconducting layer and no additional stabilizer layer. A dry film resist (DFR) was laminated on top of the HTS tape by a lamination method for the segmentation. Exposure to a 395 nm UV lamp on a patterned mask cures the DFR. Dipping with a 1% Na₂CO₃ solution was followed to develop the uncured film side and to obtain the required pattern. The silver and superconducting layers of the REBCO films were cleaned with an acid solution after the etching. Finally, the segmented HTS tape was completed by stripping the DFR film with acetone.