• Journal of the Korean Ceramic Society
• /
• v.33 no.11
• /
• pp.1195-1202
• /
• 1996

To prepare the dielectric thin films of (Pb1-xSrx)TiO3 (x=0.1, 0.2, 0.3, 0.35, 0.5) by the sol-gel process titanium (IV) isopropoxide (Ti[OCH(CH3)2]4) and Pb Sr, acetate were used therefore the thin films were fabricated by dip-coating method. Stability of the sol decreased with addition of Sr content thin films could be fabricated up to 35mol% Over this range precipitation of sol occured thin films couldn't be obtained. Transmittance of thin films at visible range decreased with the increase of heat-treatment temperature but exhibited transmit-tance above 60% in all case. Moreover transmittance of thin films at visible range slightly increased with of addition of Sr,. When thin film containing 30 mol% srontium was heated at 600℃ the best perovskite phase was obtained. The dielectric constant (ε) was 280 and dielectric loss factor (tan δ) was 0.021 and curie tempera-ture (Tc) decreased with the increase of addition of Sr.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.49-57
• /
• 2004

The modified polyionene polyelectrolyte inks were newly prepared and applied to the humidity-sensitive membrane of humidity sensor. The films were fabricated on the alumina substrate with comb-type gold electrode using a ink-jet printing technique. The copolymers of methyl methacrylate, acrylic acid, 2-hydroxyethyl methacrylate and [(2-methacryloyloxy)ethyl]trimethylammonium chloride were also prepared for the humidity-sensing material. which was fabricated by dip-coating method. Electrical measurements under various relative humidity were performed. The humidity-sensitive characteristics of sensors obtained by ink-jet printing technique were compared with that of dip-coating method. Humidity sensors showed a decrease in resistance as an increase of relative humidity and their resistance characteristics are in a close agreement each other.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1232-1233
• /
• 2008

딥 코팅 공정을 통하여 콜로이드 $Fe_2O_3$ 나노입자의 단일층을 다공성의 AAO (Anodic Aluminum Oxide) 기판에 형성하였다. 나노입자의 평균 사이즈는 20 nm이고, 각각의 나노입자는 올레익 산(oleic acid) 으로 둘러싸여 옥탄(octane) 용액 안에 분산되어있다. AAO 기판은 알루미늄에 높은 균일성과 고밀도의 기공(pore) 형성을 위해 두 단계 양극산화공정을 통해 제작하였다. AAO 기공의 지름은 ${\sim}$30에서 100 nm 이고, 딥 코팅 공정의 속도는 0.1 mm/sec 로 하여 AAO의 나노기공 안에 나노입자의 단일층을 성공적으로 형성시켰다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.42.2-42.2
• /
• 2010

Recently, highly porous bone substitutes, which have interconnected open pore structure, have been focused on improving their mechanical properties and modifying their functions. Especially, it is highly required to develop functional gradient structured bone substitute which is available for controlling their material properties such as bioresorption rate and elastic modulus. Porous $ZrO_2$ scaffold was fabricated by the sponge replica method using PU sponge. After 3 times of dip coating and the subsequent oven drying, burning out and microwave sintering were carried out. Various $ZrO_2$-BCP powder mixtures were prepared depending on the ratio and coated on the $ZrO_2$ scaffold by dip coating process. X-ray diffraction analysis was performed to characterize the phase identification of the scaffolds. Microstructures of the bone substitutes were observed using scanning electron microscopy.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.445-449
• /
• 1999

Hydrophilic polyphosphazenes were synthesized from hydrophobic polyphosphazenes by adding methoxyethylenoxy side chains and cast by dip-coating method into membranes supported on porous polypropylene mesh filter sheet for metal separation testing. A solution of $Cr^{3+},\;Co^{2+},\;Mn^{2+}$ nitrates was used in diffusion experiments which were conducted from $25^{\circ}C$ to $60^{\circ}C$. lt was found that the ion transport properties were increased as the repeating number of ethylenoxy side chain increased. Membrane from trifluoroethoxy methoxyethoxyethoxyethoxy co-substituted polyphosphazenes was found to separate $Cr^{3+}$ ion from $Mn^{2-}$ and $Co^{2+}$ ions with separation factor of 4.5 at $60^{\circ}C$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.131-133
• /
• 2012

The photoluminescence (PT) properties of Al-doped ZnO thin films grown by the sol-gel dip-coating method have been investigated. At 12 K, nine distinct PL peaks were observed at 2.037, 2.592, 2.832, 3.027, 3.177, 3.216, 3.260, 3.303, and 3.354 eV. The deep-level emissions (2.037, 2.592, 2.832, and 3.027 eV) were attributed to native defects. The near-band-edge (NBE) emission peaks at 3.354, 3.303, 3.260, 3.216, and 3.177 eV were attributed to the emission of the neutral-donor-bound excitons (D0X), two-electron satellite (TES), free-to-neutral-acceptors (e,A0), donor-acceptor pairs (DAP), and second-order longitudinal optical (2LO) phonon replicas of the TES (TES-2LO), respectively. According to Haynes' empirical rule, we calculated the energy of a free exciton (FX) to be 3.374 eV. The thermal activation energy for D0X in the nanocrystalline ZnO thin film was found to be ~25 meV, corresponding to the thermal dissociation energy required for D0X transitions.

• Membrane Journal
• /
• v.6 no.3
• /
• pp.182-187
• /
• 1996

Hydrophilic poly(acrylonitrile) [PAN] membrane with good molecular weight cut-off characteristics were prepared by using the phase inversion method. Permeability and molecular weight cut-off of the membranes were measured through the ultrafiltration test. On the surface of the PAN support membranes, poly(acrylic acid) [PAA] was deposited by dip-coating. The water permeability of the PAN support membrane had $0.17~31\textrm{mm}^3/m^{2} \cdot s \cdot Pa$, the molecular weight cut-off 42, 000~150, 000. The transport characteristics of the prepared composite membranes were significantly affected by the variation of the support membrane mophology. The permeability of the composite membrane was decreased with increasing molecular weight cut-off of the support membrane, and the separation factor was slightly changed depending on the feed concentration.

• Corrosion Science and Technology
• /
• v.9 no.2
• /
• pp.98-103
• /
• 2010

In order to further reduce the cost without reducing the corrosion resistance, a high-manganese austenitic alloy for sink roll or stabilizer roll in continuous hot-dip coating lines was developed. A systematic study of corrosion behavior of the high-manganese austenitic alloy in pure zinc bath at $490^{\circ}C$ was carried out. The results shows that, the high-manganese austenitic alloy shows better corrosion resistance than 316L steel. The corrosion rate of the high-manganese austenitic alloy in pure zinc bath is calculated to be approximately $6.42{\times}10^{-4}g{\cdot}cm^{-2}{\cdot}h^{-1}$, while the 316L is $1.54{\times}10^{-3}g{\cdot}cm^{-2}{\cdot}h^{-1}$. The high-manganese austenitic alloy forms a three-phase intermetallic compound layer morphology containing ${\Gamma$}, ${\delta}$ and ${\zeta}$ phases, while the 316L is almost ${\zeta}$ phase. The ${\Gamma}$ and ${\delta}$ phases of the high-manganese austenitic alloy contain about 8.5 wt% Cr, the existence of Cr improve the stabilization of phases, which slow down the reaction of Fe and Zn, improve the corrosion resistance of the high-manganese austenitic alloy. So substitute the nickel with the manganese to manufacture the high-manganese austenitic alloy of low cost is feasible.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.584-587
• /
• 2011

In this work, the $TiO_2$ and $SnO_2$ thin films as blocking layers were coated directly onto the metal-mesh electrode surface to prevent unnecessary inflow of back-transfer electrons from the electrolyte ($I^-/I_3^-$) to the metal-mesh electrode. The DSCs were fabricated with working electrode of SUS mesh coated with blocking $TiO_2$ and $SnO_2$ layers, dye-attached mesoporous $TiO_2$ film, gel electrolyte and counter electrode of Pt-deposited F:$SnO_2$. From the experimental result, it was ascertained that the efficiency of metal electrode coated with $TiO_2$ by Dip-coating was superior to that of metal electrode coated with $SnO_2$ by Dip-coating and screen printing with the results of experiments. The photo-current conversion efficiency of the cell obtained from optimum fabrication condition was 3% ($V_{oc}$=0.61V, $J_{sc}$=11.64 mA/$cm^2$, ff=0.64) under AM1.5, 100 mW/$cm^2$ illumination.

• Korean Journal of Materials Research
• /
• v.22 no.10
• /
• pp.526-530
• /
• 2012

Silica-based ceramic-matrix composites have shown promise as advanced materials for many applications such as chemical catalysts, ceramics, pharmaceuticals, and electronics. $SiO_2$-CuO-$CeO_2$ multi-component powders and their thin film, using an oxalic acid template as a chelating agent, have larger surface areas and more uniform pore size distribution than those of inorganic acid catalysts. $SiO_2$-CuO-$CeO_2$ composite powders were synthesized using tetraethylorthosilicate, copper (II) nitrate hemi (pentahydrate), and cerium (III) nitrate hexahydrate with oxalic acid as template or pore-forming agent. The process of thermal evolution, the phase composition, and the surface morphology of these powders were monitored by thermogravimetry-differential thermal analysis (TG-DTA), X-ray diffractometry (XRD), field-emission scanning electron microscopy (FE-SEM), and energy dispersive X-ray spectrometry (EDXS). The mesoporous property of the powders was observed by Brunner-Emmett-Teller surface (BET) analysis. The improved surface area of this powder template with oxalic acid was $371.4m^2/g$. This multi-component thin film on stainless-steel was prepared by sol-gel dip coating with no cracks.