• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.239-245
• /
• 2016

In this study, a 12 V PWM boost converter was designed with the optimal values of the external components of the power stage was well as the compensation stage for smart electronic applications powered by a battery device. The 12 V boost PWM converter consisted of several passive elements, such as a resistor, inductor and capacitor with a diode, power MOS switch and control IC chip for the control PWM signal. The devices of the power stage and compensation stage were designed to maintain stable operation under a range of load conditions as well as achieving the highest power efficiency. The results of this study were first verified by a simulation in SPICE from calculations of the values of major external elements comprising the converter. The design was also implemented on the prototype PCBboard using commercial IC LM3481 from Texas Instruments, which has a nominal output voltage of 12 V. The output voltage, ripple voltage, and load regulation with the line regulation were measured using a digital oscilloscope, DMM tester, and DC power supply. By configuring the converter under the same conditions as in the circuit simulation, the experimental results matched the simulation results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.34-47
• /
• 2018

As interest in advanced countries regarding the convergence technology development increases, a methodology for identifying the core convergence technology that has a large spill-over effect on the technology and industry is required for the nation's competitiveness enhancement in the convergence technology field. Based on patent citation network analysis using 1,124 USPTO patents in the ICT convergence technology field of the smart factory, this study examined the proposed heterogeneous technology convergence index as a tool for measuring the convergence characteristics of the spillovers compared to other indexes (i.e. other sector ratio index and homogeneous technology convergence index). The proposed heterogeneous technology convergence index was used to investigate core technology sectors among ICT technology sectors of smart factory identified by government ministries. Results found 6 core ICT convergence technology sectors including the manufacturing execution analysis application sector. Also, this study conducted blockmodeling analysis using the IPC codes of patents in the manufacturing execution analysis application sector, and identified that the blocks representing the electronic communication and electric digital data processing technology sectors (Block 3 & 4) are related technology sectors which can be converged with core technology. Based on the findings, the implications for the convergence technology development planning of the smart factory field are discussed.

• Journal of Distribution Science
• /
• v.11 no.10
• /
• pp.17-25
• /
• 2013

Purpose - This study analyzes the effect of customers' perceived service innovativeness of service centers for electronic goods, on repurchase intentions of customers, using behavior intentions of service centers as a mediator variable. In customer management and customer relationship marketing, service centers can be the most representative customer relationship management departments because they are most closely placed at the interface with customers. In addition, this study intends to investigate if continuous relationship with customers during one-time product-selling can affect their repurchase intentions. Specifically, this research aims to investigate if the expansion of the saturated physical market of the manufacturing business, to intangible service markets, can be competitive enough to satisfy customer needs. Research design, data, and methodology - This study targets college students, and especially those who have computers, digital cameras, or cell-phones, and often use electronic products and services. In order to investigate our hypothesis, we analyzed dates through SEM (structural equation modeling) using SPSS for Windows 18.0 and AMOS 18.0. In addition, we measured Cronbach's α coefficient using SPSS for Windows 18.0 in order to measure reliability. Further, using AMOS 18.0, this research statistically measured convergent validity as well as discriminant validity, and examined mediation models and path models in which service innovativeness leads to customers' repurchase intentions of electronic products. Results - As a result, this research shows that customers' perceived service innovativeness of service centers for electronic goods has significant positive influence on customers' behavior intentions of service centers. In addition, service innovativeness of electronic goods' service centers also has significant positive influence on repurchase intentions of customers. Conclusion - This study investigates the effect of customers' positive relation with the innovativeness of electronic service center on their behavior intention and product repurchase. The more concrete, important results of the study are as follows. Through the mediating effect, the findings of the study suggest that customers' behavior intentions of service centers partially mediate the effect of customers'perceived service innovativeness of service centers for electronic goods on customers' repurchase intentions. This research also provides an insight that the importance of service innovativeness and innovative approaches in managing customers should be recognized in the process of repurchase and service roles of manufacturing business as a way for customer management. As a result, the relationship between customer satisfaction and service quality of service centers for the electronic products is very sensitive. Although previous studies focus on certain aspects of the case for enhancing service innovation (Kim, 2012), this research recommends that the service centers need to understand the customers'desire first and try to adapt to achieve customer satisfaction by being innovative. This innovativeness of service centers would make customers visit them consistently, which in the long run, will also influence their repurchase decisions.

• Journal of dental hygiene science
• /
• v.15 no.1
• /
• pp.54-59
• /
• 2015

The present study investigated the influences of various abutment teeth shapes (maxillary right canine, pre-molar, molar) on the marginal adaptation of computer aided design/computer aided manufacturing-fabricated zirconia core. In vitro adaptation of zirconia cores manufactured by three different abutments were evaluated. Thirty zirconia cores were made per each models and the adaptation was evaluated through a silicone replica technique. The measurement of the adaptation was carried out using digital microscope. The mean and standard deviation of each reference point were analyzed using the one-way (ANOVA) and Tukey's honestly significant difference tests (${\alpha}=0.05$). The overall marginal fits of the zirconia cores were as follows: canine: $47.59{\mu}m$, pre-molar: $43.74{\mu}m$, molar: $40.36{\mu}m$. They were no statistically significant differences between groups for adaptation (p>0.05). This confirmed that the type of abutment teeth used does not determine the precision of fit of zirconia core.

• Journal of dental hygiene science
• /
• v.18 no.4
• /
• pp.265-270
• /
• 2018

The purpose of this study was to investigate the chemical properties of some commercially available mouthwashes and to ascertain whether the mouthwashes accelerated mineral loss in dental enamel. Five commercially available mouthwashes were selected from the three largest malls in Korea: Perio Total 7 Aqua Cool Mint Strong $Fresh^{TM}$ (PS; LG Household & Health Care Ltd.), Garglin $Original^{TM}$ (Dong-A Pharmaceutical Co., Ltd.), Garglin $Zero^{TM}$ (Dong-A Pharmaceutical Co., Ltd.), Listerine Naturals $Citrus^{TM}$ (LC; IDS Manufacturing Ltd.), and Listerine Cool $Mint^{TM}$ (LM; IDS Manufacturing Ltd.). The composition, pH, and titratable acidity of the mouthwashes were investigated. Six bovine teeth specimens were prepared for each mouthwash group. Each of the six specimens was individually immersed in 30 ml aliquots of mouthwash for 1 minute, 30 minutes, 90 minutes, and 120 minutes, and the samples were placed in a $36.5^{\circ}C$ stirred incubator. The degree of mineral loss (${\Delta}F$) of the tooth surface area exposed to mouthwash, compared with normal teeth, was analyzed by quantitative light-induced fluorescence-digital. The difference in ${\Delta}F$ among mouthwash groups was examined by the Kruskal-Wallis H test (${\alpha}=0.05$). The contents of mouthwashes differed between Listerine and other products, and the pH ranged from 4.09 to 6.75. The titratable acidity of PS was the lowest at 0.63 ml and highest at 9.25 ml for LM. Minor mineral loss was observed when dental specimens were immersed in the Listerine products (LC and LM) for more than 90 minutes, but the degree of mineral loss for Listerine products was not statistically significantly different from that for groups without mineral loss. In conclusion, all five commercially available mouthwashes showed no harmful effects on tooth enamel.

• Design & Manufacturing
• /
• v.15 no.2
• /
• pp.23-29
• /
• 2021

The specific strength of magnesium alloy is four times that of iron and 1.5 times that of aluminum. For this reason, its use is increasing in the transportation industry which is promoting weight reduction. At room temperature, magnesium alloy has low formability due to Hexagonal closed packed (HCP) structure with relatively little slip plane. However, as the molding temperature increases, the formability of the magnesium alloy is greatly improved due to the activation of other additional slip systems, and the flow stress and elongation vary greatly depending on the temperature. In addition, magnesium alloys exhibit asymmetrical behavior, which is different from tensile and compression behavior. In this study, a jig was developed that can measure the plane deformation behavior on the surface of a material in tensile and compression tests of magnesium alloys in warm temperature. A jig was designed to prevent buckling occurring in the compression test by applying a certain pressure to apply it to the tensile and compression tests. And the tensile and compressive behavior of magnesium at each temperature was investigated with the developed jig and DIC equipment. In each experiment, the strain rate condition was set to a quasi-static strain rate of 0.01/s. The transformation temperature is room temperature, 100℃. 150℃, 200℃, 250℃. As a result of the experiment, the flow stress tended to decrease as the temperature increased. The maximum stress decreased by 60% at 250 degrees compared to room temperature. Particularly, work softening occurred above 150 degrees, which is the recrystallization temperature of the magnesium alloy. The elongation also tended to increase as the deformation temperature increased and increased by 60% at 250 degrees compared to room temperature. In the compression experiment, it was confirmed that the maximum stress decreased as the temperature increased.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.2
• /
• pp.153-159
• /
• 2023

Computer-aided design-computer-aided manufacturing technology has been widely used in the manufacture of fixed prostheses including implants, but in the case of removable dentures, the analog method is still being used due to the errors such as a lack of fusion and over-fusion in selective laser meting process. With the recent development of CAD software, virtual surveying and framework design are made possible, and the designed file can be manufactured by milling or 3D printing. It replace the analog method of waxing and denture curing process and also can reduce the production time and cost. Therefore, this case is reported because good clinical results were obtained by digitally surveying on CAD software to produce a surveyed metal restoration and framework on maxillary and mandibular removable dentures.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.230-238
• /
• 2023

Small and medium-sized food manufacturing enterprises are largely reliant on manual labor, from inputting raw materials to palletizing the final product. Recently, there has been a trend toward smartness and digitization through the implementation of robotics and sensor data technology. In this study, we examined the effectiveness of improvement through 3D simulation on two repetitive work processes within a food manufacturing company. These processes involve workers whose speed cannot match the capacity of the applied equipment. Two manual processes were selected: the weighing and packing process performed by workers after skewer assembly, and the manual batch process of counting randomly delivered frozen foods, packing (both internal and external), and palletizing. The production volume, utilization rate, and number of workers were chosen as verification indicators. As a result of the simulation for improving the 3D process, production increased by 13.5% and 56.8% compared to the existing process, respectively. This was particularly evident in the process of applying palletizing robots. In both processes, as the utilization rate and number of input workers decreased, robots could replace tasks with high worker fatigue, thereby reducing work overload. This study demonstrates the potential to visually compare the process flow improvement using 3D simulations and confirms the possibility of pre-validation for improvement.

• Journal of Digital Convergence
• /
• v.14 no.5
• /
• pp.165-176
• /
• 2016

The purpose of this study is to examine the effects of the IT resources on the work efficiency and corporate performance in Mobile Smart-Work Environment with IT convergence Technology by applying the Resource-Based View. The study has an academic meaning by empirically analyzing the effects of factors identified based on the existing study on the IT resources in Mobile Smart-Work, and practical implications to identify how the significance of the Mobile Smart-Work used as a platform of variety industries in manufacturing, logistics, service, distribution, finance, public institutions, and so on positively affects improvement of corporate efficiency and performance. The results showed that IT Infrastructure and IT skills in the Mobile Smart-work environment were found to bring positive effects on individual work efficiency, and IT skills had positive influence on team work efficiency. Also, we confirmed the individual and team work efficiency positively affect financial and market performance of business firms. Finally, we expect that business firm equipped with IT resources in the Mobile Smart-Work environment with IT convergence Technology. It can improve this work efficiency and the performance, which leads to strengthening the core competency.

• Journal of Digital Convergence
• /
• v.11 no.12
• /
• pp.229-236
• /
• 2013

This study defined that the construct of work-family is not the opposite meaning but the construct having positive synergy effects each other. For more meaningful implications to HR partitioner in the era of smart working, Data collection was done from the manufacturing companies in Kyungsangnamdo and hierarchical regression was conducted. we investigated the relationship between work-family facilitation and organizational commitment and moderating effect of perceived organizational support between work-family facilitation and organizational commitment. Based on the result, we have proposed some implications. First, we should study more detail processes between work-family facilitation and organizational commitment not only continuous commitment but also affective and normative commitment. Second, we could know that not only work-family balance but also work-family facilitation could positively impact on organizational commitment, there when we design the job of employees, we should consider the family issues of job holder.