• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1204-1211
• /
• 2004

It is difficult to apply a conventional selection guide for diffusers when the diffuser is installed in a perimeter zone, because the air diffusion performance index (ADPI) vs. throw/length (T/L) ratio curve listed in conventional guide does not consider the perimetric heating load through the walls. The objective of this study is to evaluate the effect of the perimetric heating load on the ADPI and propose a selection guide for a proper line diffuser when perimetric heating load exists. The velocity and temperature distributions and the ADPI values are obtained numerically with various heat load ratios and air flow rates. The velocity and temperature distributions and the ADPI values are analyzed by CFD in case of various heat load ratios and air flow rates. Also, ADPI was calculated by those results. The ADPI values by numerical results are compared with an existing experimental data to verify the method for the evaluation of ADPI proposed in a present study. In case of a line diffuser installed at the high side wall, the ADPI decreases according to the increases of the flow rate on every heat load ratio of the present study except 0.75. The ADPI vs. T/L ratio curves have been proposed for the heat load ratios of 0.25, 0.5, 0.75 to guarantee the comport thermal environment when diffusers are installed in perimeter zone.

• Nuclear Engineering and Technology
• /
• v.52 no.5
• /
• pp.869-877
• /
• 2020

A 24-month Advanced Power Reactor 1400 (APR1400) core with a very-low-boron (VLB) concentration has been investigated for an inherently safe and high-performance PWR in this work. To develop a high-performance APR1400 which is able to do the passive frequency control operation, VLB feature is essential. In this paper, the centrally-shielded burnable absorber (CSBA) is utilized for an efficient VLB operation in the 24-month cycle APR1400 core. This innovative design of the VLB APR1400 core includes the optimization of burnable absorber and loading pattern as well as axial cutback for a 24-month cycle operation. In addition to CSBA, an Er-doped guide thimble is also introduced for partial management of the excess reactivity and local peaking factor. To improve the neutron economy of the core, two alternative radial reflectors are adopted in this study, which are SS-304 and ZrO₂. The core reactivity and power distributions for a 2-batch equilibrium cycle are analyzed and compared for each reflector design. Numerical results show that a VLB core can be successfully designed with 24-month cycle and the cycle length is improved significantly with the alternative reflectors. The neutronic analyses are performed using the Monte Carlo Serpent code and 3-D diffusion code COREDAX-2 with the ENDF/B-VII.1.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.42-54
• /
• 2021

The Aft-deck is being applied to the latest unmanned aircraft for the purpose of shielding the gas turbine exhaust plume or spreading jets to increase the mixing rate with the ambient air, thereby reducing the temperature of exhaust gases. In this study, we would like to find out how the performance of the nozzle is affected by the design variables of the Aft-deck. The design variables of aft-deck are selected as length, expansion angle and upper deck shape. The correlation between thrust and plume shielding rate with the length variable is presented. And the correlation between the thrust and the jet diffusion range is presented according to the expansion angle. In addition, the thrust increase effect is confirmed by the removal of the upper deck and the characteristics of transverse velocity vector determined mixing performance with external flow.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.1
• /
• pp.18-21
• /
• 2007

Highly textured MgO template by ion-beam-assisted deposition(IBAD) was successfully fabricated using a continuous reel-to-reel(R2R) mode. To enlarge the deposition area, the previous IBAD system was modified into the system with 14-pass and five heating zone. Every processing step was carried out using this multi-turn IBAD system. The overall process consists of R2R electropolishing of a hastelloy C276 tape, deposition of $Al_2O_3$ diffusion barrier, $Y_2O_3$ seed layer, IBAD-MgO and homoepi-MgO layer. The IBAD-MgO templates were fabricated using the IBAD system with 216 cm-length deposition zone and 32 cm diameter ion source. The texture of MgO films developed during the IBAD process was monitored by in-situ reflection high energy electron diffraction(RHEED) to optimize the IBAD process. Recently, 100 m long IBAD-MgO tape with in-plane texture of $\Delta{\phi}<10^{\circ}$ was successfully fabricated using the modified IBAD system. In this report, the detailed deposition condition of getting a long length IBAD-MgO template with a good epitaxy is described.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.11 no.2
• /
• pp.51-60
• /
• 2003

In the nuclear power plant, emergency core coolant system (ECCS) is furnished at reactor coolant system (RCS) in order to cool down high temperature water in case of emergency. However, in this coolant system, thermal stratification phenomenon can occur due to coolant leaking in the check valve. The thermal stratification produces excessive thermal stresses at the pipe wall so as to yield thermal fatigue crack (TFC) accident. In the present study, effects of turbulence penetration on the thermal stratification into T-branches with square cross-section in the modeled ECCS are analysed numerically. Standard k-$\varepsilon$ model is employed to calculate the Reynolds stresses in momentum equations. Results show that the length and strength of thermal stratification are primarily affected by the leak flow rate of coolant and the Reynolds number of duct. Turbulence penetration into the T-branch of ECCS shows two counteracting effects on the thermal stratification. Heat transport by turbulence penetration from main duct to leaking flow region may enhance thermal stratification while the turbulent diffusion may weaken it.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.9
• /
• pp.2583-2588
• /
• 2013

A new type of solid and gel-state ionics based on siloxane pyridinium iodides was synthesized and used as electrolytes in dye-sensitized solar cells. The resulting electrolytes were characterized by $^1H$ NMR spectroscopy, TGA and diffusion coefficient. The synthesized siloxane pyridinium iodide electrolytes have characteristics of different chain length of siloxane moieties. The ion conductivities were given 2.7-3.2 S/cm. Among the three SiDPIs based electrolytes, DSSC employing the SiDPI2 gives an open circuit voltage of 0.704 V, a short-circuit current of 15.85 $mA/cm^2$ and conversion efficiency of 6.8% under light intensity of 100 $mW/cm^2$. In addition, the performance of the DSSCs showed relatively reasonable compared with the propylpyridinium iodide (PPI) electrolyte.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.163.1-163.1
• /
• 2016

Lead halide perovskites CH3NH3PbX3 (X=Cl, Br, I) have received great interest in the past few years because of their excellent photoelectronic properties as well as their low-cost solution process. Their theoretical efficiency limit of the solar cell devices was predicted around 31% by a detailed balance model for the reason that exceptional light-harvesting and superior carrier transport properties. Additionally, these excellent properties contribute to the applications of optoelectronic devices such as LASERs, LEDs, and photodetectors. Since these devices are mainly using perovskite thin film, one of the most important factor to decide the efficiency of these applications is the quality of the film. Even though, optoelectrical devices are composed of polycrystalline thin film in general, not a single crystalline form which has longer carrier diffusion length and lower trap density. For these reasons, monodomain perovskite thin films have potential to elicit an optimized device efficiency. In this study, we analyzed the crystallography of the in-plane aligned perovskite thin film by X-ray diffraction (XRD) and selected area electron diffraction (SAED). Also the basic optic properties of perovskites were checked using scanning electron microscopy (SEM) and UV-Vis spectrum. From this work, the perovskite which is aligned in all directions both of out-of-plane and in-plane was fabricated and analyzed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.196.2-196.2
• /
• 2015

There are various issues fabricating the successful and efficient solar cell structures. One of the most important issues is band alignment technique. The solar cells make the carrier in their active region over the p-n junction. Then, electrons and holes diffuse by minority carrier diffusion length. After they reach the edge of solar cells, there exist large energy barrier unless the good electrode are chosen. Many various conductor with different work functions can be selected to solve this energy barrier problem to efficiently extract carriers. Tungsten oxide has large band gap known as approximately 3.4 eV, and usually this material shows n-type property with reported work function of 6.65 eV. They are extremely high work function and trap level by oxygen vacancy cause them to become the hole extraction layer for optical devices like solar cells. In this study, we deposited tungsten oxide thin films by sputtering technique with various sputtering conditions. Their electrical contact properties were characterized with transmission line model pattern. The structure of tungsten oxide thin films were measured by x-ray diffraction. With x-ray photoelectron spectroscopy, the content of oxygen was investigated, and their defect states were examined by spectroscopic ellipsometry, UV-Vis spectrophotometer, and photoluminescence measurements.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.692-699
• /
• 2006

In this work, $TiO_2$ nanoparticles were synthesized using $N_2-diluted$ and Oxygen-enriched co-flow hydrogen diffusion flames. The effect of flame temperature on the crystalline structure of the formed $TiO_2$ nanoparticles was investigated. The measured maximum centerline temperature of the flame ranged from 2,103k for oxygen-enriched flame to 1,339K for $N_2-diluted$ flame. The visible flame length and the height of the main reaction zone were characterized by direct photographs. The crystalline structures of $TiO_2$ nanoparticles were analyzed by XRD. From the XRD analysis, it was evident that the crystalline structures of the formed nanoparticles were divided into two sorts. In the higher temperature region, over the 1,700K, the fraction of formed $TiO_2$ nanoparticles having anatase-phase crystalline structure increased with increasing the flame temperature. On the contrary, in the lower temperature region, below the 1,600K, the fraction of anatase-phase nanoparticles increased with decreasing the flame temperature.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.4
• /
• pp.111-115
• /
• 2009

We present a study on the reflection of optically controlled microwave pulses from non uniform plasma layers in semiconductors. The transient response of the microwave pulses in different plasma layers has been evaluated by means of the reflection function of dielectric microstrip lines. The lines were used with an open-ended termination containing an optically induced plasma region, which was illuminated by a light source. The reflection characteristics impedance resulting from the presence of plasma is evaluated by means of the equivalent transmission line model. We have analyzed the variation of the transient response in a 0.01 cm layer with a surface frequency in the region of 128 GHz. In the reflection the variation of the diffusion length $L_D$ is large compared with the absorption depth $1/{\alpha}_l$. The variation of the characteristic response of the plasma layer with differentially localized pulses has been evaluated analytically. The change of the reflection amplitude has been observed at depths of 0.1 cm, 0.01 cm and $0.1{\times}10^{-5}$ cm respectively.