• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.1
• /
• pp.63-70
• /
• 1997

A study was performed to examine the aging behaviors of Al-2.1Li-2.9Cu alloy by differential scanning calorimetry and transmission electron microscopy. DSC measurements were conducted over the temperature range of $25{\sim}550^{\circ}C$ at a heating rate of $5^{\circ}C$/min. for the specimens aged at 130, 160, $190^{\circ}C$ and $220^{\circ}C$ for various times after solution treatment at $540^{\circ}C$ for 30 minutes. The peaks due to the formation of G.P.zone were not detected in the specimens aged at 130 and $160^{\circ}C$, but those at 190 and $220^{\circ}C$ appeared in DSC curves. The heat absorption due to the dissolution of ${\delta}^{\prime}$ phase was increased with increasing aging time at $130^{\circ}C$ aging. In contrast, those values for the specimens aged at 160 and $190^{\circ}C$ were initially increased and inversely decreased at the transition time of 72 and 1 hour, respectively. The heat evolution due to the formation of $T_1$ phase was nearly unchanged at $130^{\circ}C$ aging, but at $160^{\circ}C$ and $190^{\circ}C$ aging, drastically decreased after the transition time. It can be considered that the increase of $T_1$ phase results in the decrease of ${\delta}^{\prime}$ phase when aging time is longer than the transition time. The hardness of the specimen aged at $190^{\circ}C$ is initially higher compared with that at $160^{\circ}C$, however, the peak hardness shows the lower value than that at $160^{\circ}C$.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.9-15
• /
• 2012

We prepared a series of aromatic liquid crystals (LCs) based on wholly aromatic ester units with the reactive end group methyl maleimide by means of melt condensation method, and the resulting LCs were thermally crosslinked to produce liquid crystalline thermoset (LCT) films. The synthesized LCs and LCTs were characterized with Fourier transform infrared (FTIR) spectroscopy, wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), thermomechanical analysis (TMA), and polarizing optical microscopy (POM) with a hot stage. The glass transition temperature ($T_g$) and coefficient of thermal expansion are strongly affected by the mesogen units in their main chain structures. The $p$-substituted biphenyl LC was found to have the highest thermal property value.

• Archives of Pharmacal Research
• /
• v.16 no.2
• /
• pp.129-133
• /
• 1993

Temperature sensitive liposomes(TSL) containing adriamycin (ADM) and cytarabine (Ara-C) were prepared. ADM and Ara-C were selected as model compounds of amphiphilic and hydrophilic drug, respectively. Encapsulation efficiency of ADM entrapped into TSL was about twice greater than that of Ara-C. It might be due to different polarity of the drug, Lipid compositions of TSL had no effect on the encapsulation efficiency of drugs. Thermal behavior of TSL using a differential scanning calorimetry (DSC) was also investigated. Phase transition of TSL using a differential scanning calorimetry (DSC) was also investigated. Phase transition temperature $(T_c)$ of TSL was dependent on the lipid compositions of TSL ADM broadened thermogram of TSL but Ara-C did not. However, $T_c$ of TSL was not changed by any drug. Release rate of drugs was highly dependent on temperature. The release profile of ADM was similar to that of Ara-C. The maximum release rate of drugs from TSL was occurred at the near $T_c$ and observed at $39-41^\circ{C}$ for DPPC (Dipalmitoylphosphatidylcholine) only, $52-54^\circ{C}$ for DPPC and DSPC (1:1), respectively. Effect of human serum alburmin (HAA) on the release rate of ADM was investigated. HSA had no significant effect on the release of ADM below $T_c$. However, ADM release from TSL was increased at the near and above $T_c$. The HSA-induced leakage of drug may result from the interaction of liposomal constituents with HSA structure at the near TEX>$4^\circ{C}$. From the fact that the release profiles of ADM from freshly prepared TSL and stored TSL for 1 week at TEX>$4^\circ{C}$ was not changed, the TSL was considered to be stable for at least 1 week at TEX>$4^\circ{C}$. Based on these findings, TSL may be useful to deliver drugs to preheated target sites due to its thermal behaviors.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.83-87
• /
• 2022

Recently, as the thickness of the semiconductor package becomes thinner, warpage has become a major issue. Since the warpage is caused by differences in material properties between package components, it is essential to precisely evaluate the material properties of the EMC(Epoxy molding compound), one of the main components, to predict the warpage accurately. Especially, the cure shrinkage of the EMC is generated during the curing process, and among them, the effective cure shrinkage that occurs after the gelation point is a key factor in warpage. In this study, the gelation point of the EMC was defined from the dissipation factor measured using the dielectric sensor during the curing process similar with actual semiconductor package. In addition, DSC (Differential scanning calorimetry) test and rheometer test were conducted to analyze the dielectrometry measurement. As a result, the dielectrometry was verified to be an effective method for monitoring the curing status of the EMC. Simultaneously, the strain transition of the EMC during the curing process was measured using the FBG (Fiber Bragg grating) sensor. From these results, the effective cure shrinkage of the EMC during the curing process was measured.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.352-357
• /
• 2012

Techniques of thermal analyses such as DSC and TGA have been used in the study of activation energy (Ea) and frequency factor (A) depending on the particle size of RDX and HMX. Activation energy and frequency factor were calculated by Kissinger's method and Vyazovkin's method. As the particle size of RDX increased, TGA showed activation energy increased, but DSC didn't show. However, In case of HMX, as the particle size increased, both of DSC and TGA showed increase in activation energy. Moreover, Vyazovkin's method can obtain activation energy and mechanism according to decomposition of RDX and HMX.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.737-744
• /
• 2002

Thermodynamic miscibility of the binary blends composed of semi-crystalline poly (butylene 2,6-naphthalate) (PBN) and amorphous poly (4-vinylphenol) (PVPh) was investigated using differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. DSC scan results showed that there was a single glass transition temperature (T$\_$g/) for each blend. Crystalline melting temperature (T$\_$m/) depression of the PBN in the blends was also observed with the increase of PVPh content. Both results of the single T$\_$g/ and the depression of T$\_$m/ for the PBN/PVPh blends indicate that the blends are thermodynamically miscible at the molecular level. FTIR spectroscopic analysis confirmed that strong intermolecular hydrogen bonding interactions between the ester carbonyl groups of the PBN and the hydroxyl groups of the PVPh are occurred.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.6
• /
• pp.293-299
• /
• 2004

In this paper, thermal and mechanical properties of electric epoxy with water aging were discussed. We made elastic epoxy specimen adding a ratio of 0〔phr〕20〔phr〕, 35〔phr〕 and 53〔phr〕 with modifier to existing epoxy. We studied mechanical property of elastic resin after absorption in water from 0 to 484 hours. As a result, diffusion factor of elastic epoxy showed 20-21${\times}$10$^{-4}$ $\textrm{mm}^2$/s and general epoxy showed 9.5${\times}$10$^{-4}$ $\textrm{mm}^2$/s. Elastic property increased linearly according to addiction and decreased according to water absorption. Tensile strength was reduced according to addition. It was affected by water absorption of micro-void of elastic epoxy. Hardness inclined to decrease after increasing according to absorbed time. In water-absorption state, it was experimented a change of heat flow by temperature of elastic epoxy and change of thermal expansion coefficient. DSC (Differential Scanning Calorimetry) and TMA (Thermomechanical Analysis) equipments were used to measure Tg. A temperature ringe of DSC was from -0($^{\circ}C$) to 200($^{\circ}C$). One of TMA was from -0($^{\circ}C$) to 350($^{\circ}C$). In addition, we investigated structural analysis of water absorbed specimen using SEM (Scanning Electron Microscope).

• Composites Research
• /
• v.21 no.1
• /
• pp.16-21
• /
• 2008

The cure behavior of epoxy resin with a conventional amide-type hardener(HD) was investigated in the presence of castor oil(CO), cashew nut shell liquid(CNSL) and CNSL-formaldehyde resin(CFR) by using a dynamic differential scanning calorimetry(DSC). The activation energy of curing reaction was also calculated based on the non-isothermal DSC thermograms at various heating rates. An one-stage curing was noted in the case of epoxy resin filled with CO, while the epoxy resin with CNSL and CFR showed a two-stage curing process. A competitive cure reaction was noted for the epoxy resin/CNSL(or CFR)/HD blends. In the absence of HD, the CFR showed lower values of curing enthalpy than that of CNSL. The activation energy of epoxy resin curing increased with increasing the CNSL and CFR loading.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1996.11a
• /
• pp.43-48
• /
• 1996

It is considered that automobile inner space is dangerous due to its combustion characteristics. (Automobile interior is largely made by plastic materials.) At last it is necessary to study on combustion characteristics of automobile interior. we could obtain its rapid combustion velocity and high smoke density by using ASTM D 2863 apparatus, DSC (Differential Scanning Calorimetry), Smoke density apparatus and so on. The study is summerized by following conditions and results. 1. Sample size was 150mm(length)$\times$60mmwidth). 2. Combustion velocity appeared peak point in the 2cm point. 3. PVC and foam layers are important factors in the face of smoke density. 4. Using DSC, we obtained the point that automobile interior was melted. 5. Automobile interior should be improved because of its low L.O.I value and rapid flame propagation velocity.

• Journal of Pharmaceutical Investigation
• /
• v.31 no.2
• /
• pp.119-123
• /
• 2001

Six polymorphic modifications of Balofloxacin (Q-35) were obtained by the recrystallization from different organic solvents and characterized by differential scanning calorimetry (DSC), X-ray powder diffraction (XRPD). The dissolution patterns of these six modifications were also checked in distilled water at $37{\pm}0.5^{\circ}C$, 50 rpm for 60 minutes. The polymorphic modifications showed significant differences in the dissolution rate. The dissolution rate of Mod. 1 was faster than that of other polymorphic modifications. The transformation during storage was also studied.