• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.7
• /
• pp.1019-1029
• /
• 2008

In this study, visual investigation of sprays and flames has been performed and soot formation in Diesel and GTL fuels has been compared in a specially designed Rapid Charging Combustion Vessel (RCCV) under various ambient gas $O_2$ concentrations and two injection pressures. It has been concluded that soot in the mixing-controlled combustion of Diesel and GTL fuels has similar tendency to be formed in the leading portion of the jet boundaries. Auto-ignition delay for GTL fuel is shorter than that for diesel fuel. The temporal and special variation of soot concentration in the diesel flame jets at various $O_2$ concentrations was correlated with the heat release rate. Soot concentration appears in the regions when diffusion combustion starts, and its concentration reaches maximum at the peak of heat release curve and then decreases due to oxidation. Visualization by shadowgraph method showed that soot decreases with lower $O_2$ concentration, and higher injection pressure.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.1
• /
• pp.89-97
• /
• 2017

Butanol has an ability to improve the ignition quality due to its lower latent heat of vaporization; it has an advantage to reduce a volume of a fuel tank because its energy density is higher than that of ethanol. Also, butanol-diesel oil blending quality is good because butanol has an effect to prevent the phase-separation between two fuels. Even if the blended oil contains water, it can reduce the corrosion of the fuel line. Thus, it is possible to use butanol-diesel oil blended fuel in diesel engine without modification, and it may reduce the environment pollution due to NOx and particulate and the consumption of diesel oil. Therefore, some studies are being advanced whether butanol is adequate as an alternative fuel for diesel engines, and the results of the combustion and exhaust gas emission characteristics are being presented. Though the injection and spray characteristics of butanol are more important in diesel combustion, the has not yet dealt with the matter. In this study, the influence in which differences of physical properties between butanol and diesel oil may affect the injection and spray characteristics such as injection rate, penetration, spray cone angle, spray velocity and process of spray development were examined by using CRDI system, injection rate measuring device and spray visualization system. The results exhibited that the injection and macroscopic spray characteristics of two fuels were nearly the same.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.102-109
• /
• 1994

As a fundamental study to apply high pressure injection system to direct injection diesel engine, fuel injection system and constant volume combustion chamber were made and the behaviors of evaporating spray with the variation of injection pressure and the ambient gas temperature were observed by using high speed camera, and the combusion characteristics with the variation of injection pressure and A/F ratio were analyzed. As injection pressure increases, spray tip penetration and spray angle increase and, as a results spray volume increases. This helps an uniform mixing of fuel and air. Spray liquid core length decreases as ambient gas temperature increases, while it decreases as injection pressure increases but the effect of ambient gas temperature is dorminant. As injection pressure increases, ignition delay is shortened and combustion rate being raised, maximum heat release rate increases. It become clear that High injection pressure has high level of potential to improve the performance of DI-diesel engine.

• Journal of ILASS-Korea
• /
• v.5 no.4
• /
• pp.33-39
• /
• 2000

The behavior of the 2-stage spray was studied by using the schlieren method with the high pressure common-rail injection system. The spray injected 2 times with the interval of $0.3ms{\sim}1.5ms$ between the 1st and the 2nd spray in a modeled combustion chamber of constant volume bomb. In this case, the quantity of injected fuel of 1st and 2nd also changed. The schlieren photograph shows that the 2nd spray goes further away than the 1st spray when the quantity of the 1st spray is less than that of the 2nd spray. The dispersion of the vapour to the combustion chamber is not affect in a 10% of 1st spray quantity. When the 1st spray quantity is more than the 2nd spray, the vapour scattering of spray is good.

• Journal of ILASS-Korea
• /
• v.17 no.2
• /
• pp.94-99
• /
• 2012

The characteristics of spray behavior and injected amount were studied with two types of nozzles for using in a compression ignition engine with dual fuel technology for construction machines. A penetration length of spray tends to shorten due to a decrease of injected amount of a diesel fuel with dual fuel engine application. In order to ignite the gaseous fuel premixed with air during intake process, a diesel fuel, which was compression ignited, needs to penetrate somehow similar depth compared with the case of a diesel fuel-only-injection. In this work, a nozzle with reduced hole diameter and increased number of holes was tested and demonstrated that, compared to diesel 100% case, its penetration lengths are comparable to 74% and 79%, respectively, of those of 100% and 50% supply of a diesel fuel with the baseline nozzle that has four holes and 30.4% increased diameter. This will presumably enhancement the combustion in a dual fuel engine. A design suggestion was also made in this work to achieve similar penetration length of spray with diesel 100% case to prevent combustion from being deteriorated in a dual fuel engine.

• Journal of Power System Engineering
• /
• v.17 no.2
• /
• pp.29-37
• /
• 2013

Compared to gasoline engines, diesel engines with a relatively simple ignition system are more advantageous in the application of biodeisel fuel to engine. Then in this study the comparative analysis on the spray characteristics and combustion emissions characteristic between the biodiesel(soybean oil) and diesel, the fuel for commercial diesel engine, was performed with common rail injection system. Injection pressure and ratio of biodiesel blended fuel were selected as main experimental variables. Consequently, it can be found that there is no significant difference in the macro characteristics of the spray behavior(spray penetration and spray angle) in response to change in the blend ratio of soybean oil and diesel at a fixed injection pressure, in particular, soot creation in combustion emissions in the region of low pressure was greatly affected by the blend ratio of soybean oil, however, the creation in the region of high pressure was almost unaffected by the blend ratio because of promoted atomization.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.571-577
• /
• 2005

Combustion of turbulent sprays in a direct injection diesel engine is modeled by the conditional moment closure (CMC) model. The CMC routines are combined with the KIVA code to provide conditional flame structures to determine mean state variables, instead of mean reaction rates. An independent transport equation is solved for each flame group with equal mass of sequentially evaporating fuel vapor. CMC calculation begins as the fuel mass for each flame group begins to evaporate with corresponding initialization conditions. Comparison is made with measured pressure traces for four operating conditions at different rpm's and injection conditions. Results show that the CMC model with multiple flame histories can successfully be applied to ignition and mixing-controlled combustion phases of a diesel engine.

• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.29-35
• /
• 2017

This paper describes the effects of spray breakup model constants on spray and combustion characteristics in single cylinder compression engine. KIVA-3V code coupled with a CHEMKIN chemistry solver was used for numerical analysis. In this study, spray simulations and combustion simulations are studied simultaneously. Spray simulation was conducted in constant volume to reduce the effects of air-flow as swirl or tumble. The model validation was conducted and there are little difference between experiments and simulation, this differences were reasonable. In spray simulation, the effects of model constants on spray tip penetration, spray patter and SMD were studied. Furthermore, the analysis of effects of breakup variables on combustion and emissions characteristics was conducted. The results show the KH-RT breakup model constants affects spray and combustion characteristics strongly. Increasing KH model variable (B1) and RT model constants ($C_{\tau}$, $C_{RT}$) induced slower breakup time.

• Journal of the Korean Society of Combustion
• /
• v.16 no.2
• /
• pp.40-46
• /
• 2011

The diesel pre-heater has being used in cabin heating and coolant heating of engine to reduce the engine warm up time for commercial vehicle. The pre-heaters are classified as diesel spray combustor and it forms diffusion flame. By using swirler, a recirculation flow of hot product gases is established near the fuel nozzle and it helps the maintaining of diffusion flame. The design difference of swirler can affect on reaction characteristics and temperature distribution inside pre-heater. The purpose of this study is the investigation of the effect of swirler configuration on combustion characteristics. To solve spray combustion problem, the Euler-Lagrange approach discrete model is used to track droplet trajectory and evaporation history. The PDF equilibrium model is used for chemical reaction model. These models are implemented into the FLUENT code.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.30-40
• /
• 1995

Optically accessible D. I. diesel engine with a rectangular combustion chamber was constructed to visualize the behaviors of sprays and flames in the combustion camber with the close conditions of pressure and temperature in an actual engine. The behaviors of sprays and flames in the combustion chamber as the operating conditions of this engine were photographed with high speed camera by Diffused Background Illumination Method. With photographs taken by this method, behavior of spray droplets injected into the combustion chamber, ignition points, and flame propagation were observed and analyzed at a time-and space-dependent fashion.