• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.480-486
• /
• 2016

Manufacturers have been applying several technologies that can improve the fuel economy of their cars. The regulated voltage control(RVC) system, is one of those technologies being used in passenger cars. In RVC, the voltage of an alternator is controlled depending on the electrical load demand or battery SOC, although each manufacturer differs from another in terms of detail. RVC can reduce the load of an alternator by consuming the stored energy of a battery and simultaneously generate energy. In this paper, a diesel passenger car equipped with an RVC system was tested under FTP-75 and HWFET modes to evaluate fuel economy as their initial battery SOC(100, 90, 80 and 60 %). The test results showed that the initial SOC affects fuel economy only under the FTP-75 mode. FTP-75 fuel economy of the 60% SOC was 13.2 % lower than the 100 % SOC. Also, the simultaneous consumption of the two energy sources did not appear in 60 % SOC.

• 한국시뮬레이션학회논문지
• /
• 제18권3호
• /
• pp.23-34
• /
• 2009

철도차량기지에서는 철도차량의 안전한 운행을 위해 연간검수 이상의 기기보전(지정보전, 장치보전), 차체 보전을 위한 장기계획에 의해 종합적인 유지보수 혹은 중대사고에 의한 차량의 파손으로 인한 차량의 보수작업이 이루어지는 중수선 작업을 수행한다. 본 연구에서는 용산기지 이전과 관련하여 대전철도차량관리단 부지 내에 계획 중인 CDC(Commuter Diesel Car)와 발전차를 정비하는 중수선 시설의 설계안에 대한 검증을 위한 시뮬레이션 모델을 개발하고 시뮬레이션 실험을 통하여 중수선 시설의 용량을 검증하였다. 시뮬레이션 모델은 철도공사의 중정비 검수공정도를 바탕으로 2가지 설계안의 설계용량을 검증하였다. 2가지 설계안을 평가하기 위하여 검수 완료 차량, 재장일, 작업장 점유율, 공정진행 차량수 및 입장검사 대기차량수 등 5가지를 분석하여 연간 검수용량이 충분한 설계안을 선정 하였다. 또한 우수한 결과를 보인 설계안의 연간 최대 검수 가능한 차량 수는 현재 연간 검수량 보다 약 15% 많은 총 340량임을 확인할 수 있었다.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.14-21
• /
• 2011

In diesel engines, accurate EGR control is important due to its effect on nitrogen oxide and particulate matter emissions. Conventional EGR control system comprises a PI feedback controller for tracking target air mass flow and a feedforward controller for fast response. Physically, the EGR flow is affected by EGR valve lift and thermodynamic properties of the EGR path, such as pressures and temperatures. However, the conventional feedforward control output is indirectly derived from engine operating conditions, such as engine rotational speed and fuel injection quantity. Accordingly, the conventional feedforward control action counteracts the feedback controller in certain operating conditions. In order to improve this disadvantage, in this study, we proposed feedforward EGR control algorithm based on a physical model of the EGR system. The proposed EGR control strategy was validated with a 3.0 liter common rail direct injection diesel engine equipped with a DC motor type EGR valve.

• 산업기술연구
• /
• 제26권B호
• /
• pp.11-20
• /
• 2006

LNG is a valuable fuel since it offers some environmental, energy security and economic benefits over diesel. It could be used mainly in heavy-duty trucks and buses. Car acceleration induces the slope angle of the liquid fuel in the tank. Slope angle changes the surface area wetted by liquid fuel and consequently heat leak to the tank. This research is a result of numerical simulation of the heat leak with the car acceleration to LNG tank. The "Pro-HeatLeak" Fortran program is developed and the verification test of the developed program is done. The difference between numerical results and calculated results from MathCad verification test is less than 0.07 percent. The smallest heat leak is correspond to the case without oscillation. For the high car acceleration the value of heat leak is greater than that for the small acceleration. The difference between maximum and minimum heat leak for 10 gallons of fuel vapor in the tank is about 10 percent.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.616-620
• /
• 2003

Brake action is important in train operation. In case of diesel motor cas, coachs and wagon, the brake system is only act on the stop of train, but it is emphasis on safety and convenience in urban transit system such as EMU, subwar, AGT, etc. Brake of EMU has two types. one is called service brake that is used at normal operation. The other is called emergency brake. it is used at emergency operation. Service brake bring a EMU to a halt through a blending brake that form electronic brake and frictional brake. Generally EMU compose motor car and trailer car. Blending brake bring a EMU to a halt through a blending brake that form electronic brake of motor car and frictional brake of trailer car. Blending braking technology have different characteristics each nations or manufacturing companies. but deceleration command that is parameter decide blending brake. According to deceleration command, electronic brake and frictional brake are applied differently So braking power is different. electronic brake and frictional brake must be used appropriately as deceleration command. Also braking facilities must be stopped EMU more economically and safely through revision of algorism about blending brake according to output diagram. Thus The purpose of paper is to propose blending braking control way as consideration of braking output diagram used deceleration command that influence blending brake of EMU.

• 대한기계학회논문집B
• /
• 제22권8호
• /
• pp.1101-1110
• /
• 1998

Computational investigation was conducted to examine the performance of a high pressure common-rail fuel injection system which is used to power a passenger car direct injection (Dl) diesel engine. The pipe flows were modeled by one dimensional wave equation and solved by implicit FDM Each volume of injector was considered as chambers with orifice nozzle in connections. These simulation results were compared with the experimental data of Ganser Hydromag. The comparison of needle life and rate of injection between simulation data and experimental data showed quite a good agreement Different shape of injection rate can be made by adjusting the size of inlet orifice and exit orifice in the piston chamber The pilot injection was accomplished by adjusting command signal.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.90-95
• /
• 2008

Medium and high speed marine diesel engines have been widely used as prime mover in small car ferries and fishing vessels with reduction gear. These propulsion shafting system should be installed and matched the elastic coupling between engine and reduction gear to isolate the vibratory torque. In this paper, the elastic dynamic characteristics of coupling with rubber type circular segments is confirmed by the theoretical analysis using the FEM and the hydraulic exciting test at shop. And its adaptation is investigated in the torsional vibration test in factory shop.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.789-792
• /
• 2005

The dominant noise sources of Diesel Multiple Units are powerpack, which is composed of engine, transmission and cooling system, noise and wheel-rail rolling noise. The interior noise of a running vehicle is determined by structure-borne noise and air-borne noise from these noise sources. The contributions of interior noise from each noise source are calculated by air-borne transfer functions and structure-borne transfer functions of noise sources. In this paper, source separation technique is proposed to determine these transfer functions from the results of stationary and running tests of existing vehicle. With this technique, it is possible to get hold of contributions of interior noise from .noise sources of running vehicle. This source separation technique makes it possible to take efficient measures for reduction of interior noise at the early car-development stage.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.37-43
• /
• 2003

The exhaust gas recirculation (EGR) is needed for one of various strategies to reduce NOx emission. But to get the proper EGR rate, the intake and exhaust system become complicated, also application of EGR system is difficult because of the penalty in fuel consumption and the increase in particulate matter. This study is focused on the development of EGR valve using the electrical method. The effects of EGR on the characteristics of NOx, CO, CO2 emissions and particulate mater have been investigated using small-displacement size 0.8-liters engine of diesel passenger car operating at several loads and speeds. After the analysis and comparison between conventional E-EGR valve and developed E-EGR valve performance by test bench, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1389-1396
• /
• 2008

There are many studies on the ride comfort for the train from the viewpoint of passenger. But there are only a few studies on the ride comfort for engineers in the locomotive. The railway has the track conditions, such as irregularities, rail joints, turnout, level crossing, transition curves and super-elevation ramps, which cause vibrations. Generally, the ride comfort for the train is evaluated by using the vibrations. In this study, vibration accelerations have been measured in the cabin rooms of locomotives, such as DL(Diesel-electric Locomotive), DHC(Diesel Hyduralic Car) and NEL(New-Electric Locomotive) when running on the Kyoungbu conventional line. And then, their ride comforts has been analyzed and evaluated by statistical method according to UIC 513R.