• Journal of the Korean Ceramic Society
• /
• v.32 no.10
• /
• pp.1111-1116
• /
• 1995

To use dielectric material of high power multilayer capacitor, the composition of the commercial CaTiO3 was changed to decrease the sintering temperature, and the physical and electrical properties were investigated. Series of experiments showed that CaTiO3 with sintering additives had the highest density, the highest shrinkage, the lowest dielectric constant, the lowest loss factor, and the lowest temperature coefficient of capacitance (TCC). These properties had the constant values at sintering temperature of above 120$0^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1516-1519
• /
• 1996

In this paper, a study on the electrical properties of ternary compound ceramics $[(1-y-x)BaTiO_{3}-ySrTiO_{3}-xMgTiO_3]$ fabricated 7 samples with each mol[%] by using the mixed oxide method. In this case, the sintering temperature were at $1,250[^{\circ}C]$ for 2[hr]. Also made ceramic capacitors from 7 samples, temperature coefficient of the capacitance and the variation of relative dielectric constants and loss with fixed frequency (1KHZ) were studied. In some ceramic capacitors, has shown very good properties of the dielectric constants and loss. In case of BSM-11 ceramic capacitor, is sure to the commercial capacitor which shows steady properties.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.304-306
• /
• 1987

The dielectric loss ($tan{\delta}$) and the Capacitance (C) of the PPMKA(plasma-polymerized methyl metacrylate) films were measured in the frequency range of 1KHz - 5MHz at $25^{\circ}C$. The effects of the oxidation and the heating and the plasma treatment for $tan{\delta}$ and C of PMMA were investigated. Dielectric loss of PPMMA films was inceased with the oxidized products like CO and OH. As condidates for their origin the existence of low molecula moieties and free radicals in the PPMMA, and the crosslinking made by the heating and plasma treatment have been considered.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.2
• /
• pp.43-48
• /
• 1970

The precise measurement technique for dielectric constent of high-loss nonmagnetic materials is described. This technique use6 is based upon cavity resonance method and impedance method. Dielectric constant can be calculated from simple formulas without using transcen-dental equations. The error contained in x-band yields loss tangent, 3%, and dielertric constant, 1%, for materials filled in cross section of waveguide.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.43-46
• /
• 2000

In this study, (Ba, Sr)$TiO_3$ (BST) ceramics thin films were prepared by Sol-Gel method. BST solution was made and spin-coated on Pt/$TiO_2$/Si substrate at 4000 [rpm] for 10 seconds. Coated specimens were dried at 150[$^{\circ}C$] for 5 minutes. Coating process was repeated 3 times and then sintered at 750[$^{\circ}C$] for 30 minutes. Structure and electrical characteristics of specimen was analyzed by Fractal Process. Thickness of BST ceramics thin films are about 2800[$\AA$]. Dielectric constant and loss of thin films was little decreased at 1[kHz]~1[MHz]. Dielectric constant and loss to frequency were 250 and 0.02 in BST3. The property of leakage current as the relation between the current and the voltage was that change of the leakage current was stable when the applied voltage was 0~3[V].

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1108-1115
• /
• 2004

A new type of a Rotman lens is presented in this paper fur millimeter-wave applications, such as collision avoidance radar. A dielectric slab Rotman lens is proposed to reduce the conductor loss and to create an appropriate farm for favorable implementation at millimeter-wave frequency. The proposed lens consists of a dielectric slab and slot lines whereas the conventional lenses are constructed with parallel conducting plates. The dielectric slab Rotman lens excited in TE$\_$0/ mode shows a high degree of confinement for the fields, low dispersion, and has an appropriate feed structure. A prototype lens has been designed and fabricated with 9 beam ports and 9 array ports together with 9 tapered slot antennas. This lens has been tested in the range from 10 GHz to 15 GHz and the measured beam widths are about 15$^{\circ}$ at 13 GHz. The measurements also show low mutual coupling between beam ports and an efficiency of about 34.6 %. The overall performance is comparable to that of conventional Rotman lenses even though the prototype was tested at lower than desired frequencies in the microwave frequency range due to our limited resources for fabrications and measurements. It is expected that at millimeter-wave frequency the dielectric slab Rotman lens will have lower conductor loss and lower mutual coupling than conventional Rotman lenses.an lenses.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.6
• /
• pp.1001-1007
• /
• 2002

To improve the performance of the PZT thin flms, each PZT and PT layer was alternately deposited on a Pt/Ti/Si$_3$N$_4$/SiO$_2$/Si substrate by a modified sol-gel solid precursor technique. For comparison, PZT thin films were also prepared with an identical method under the same conditions. XRD measurement revealed that the diffraction pattern of the multilayer film was due to the superimposition of the PZT and PT patterns. At 1㎑, a dielectric constant of 389 and 558, a dielectric loss of 1.2% and 1.1% were obtained for the PZT/PT and PZT thin films, respectively. If we consider the PT dielectric constant to be 260, it is clear that the dielectric constant of alternately deposited PZT/PT thin films was well adjusted. The PZT/PT thin film showed a low dielectric constant and a similar dielectric loss compared with those of the PZT film. The figures of merit on detectivity for the PZT/PT and PZT thin films were 20.3$\times$10$\^$-6/㎩$\^$-$\sfrac{1}{2}$/, and 18.7$\times$10$\^$-6/㎩$\^$-$\sfrac{1}{2}$/, and the figures of merit on voltage response were 0.038㎡/C and 0.028 ㎡/C, respectively. The high figures of merit for the PZT/PT film were ascribed to its relatively low dielectric constant when compared to the PZT thin films.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.123-130
• /
• 1997

In this study, (Sr.Pb.Ca)TiO3-Bi2O3.3TiO2(SPCT) systems were investigated to develop a new material which has a high dielectric constant, a low dielectric loss and a small TCC(Temperature Coefficient of Capa-citance), and are suitable for high voltage applications as a function of the additions of Bi2O3.3TiO2 from 5 mol.% to 9 mol.%. The result obtained from our investigation showed that up to 6 mol.% Bi2O3.3TiO ad-dition the dielectric constant increased and it deteriorated at higher concentrations with increasing amount of the acicular grains. As a result of some dopants (SiO2, Nb2O3, MnO2) addition to SPCT, the specimens with MnO2 showed good dielectric properties. The dielectric constant decreased, but the TCC was improved with the addition of MnO2 from 0.15 wt.% to 0.45 wt. %.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.35-40
• /
• 2010

The variations of dielectric properties of $Ta_2O_5-SiO_2$ continuous composition spread thin films prepared by off-axis radio-frequency magnetron sputtering were investigated. The dielectric maps of dielectric constant and loss were plotted via 1500 micron-step measuring. The specific points showing superior dielectric properties of high dielectric constant (k~19.5) and loss (tan${\delta}$<0.05) at 1 MHz were found in area of the distance of 16 mm and 22 mm apart from $SiO_2$ side in $75{\times}25mm^2$ sized Pt/Ti/$SiO_2$/Si(100) substrates.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.698-702
• /
• 2005

Dielectric and Piezoelectric properties of complex perovskite 0.92Pb($Zr_{1/2}Ti_{1/2})O_{3}-(0.08-x)Pb(Cu_{1/3}Nb_{2/3})O_{3}-xPb(Mn_{1/3}Nb_{2/3})O_{3}(0{\leq}x{\leq}0.080$) (PZT-PCN-PMN) system were investigated as a function of PMN content. With the increase of PMN content of the sintered specimens, tetragonal phase was coexisted with rhombohedral phase, the dielectric constant was decreased, mechanical quality factor ($Q_{m}$) was inceased, and optimal sintering temperature was increased up to 1050$^{\circ}C$. For the composition of x = 0.064 sintered at 1050$^{\circ}C$ for 2 h, 1939 of maximum mechanical quality factor ($Q_{m}$), 57$\%$ of electromechanical coupling factor ($k_{p}$), and 1100$^{\circ}C$ of dielectric constant, 0.37$\% $ of dielectric loss (tan $\delta$) were obtained.