• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.397-403
• /
• 1993

Widely used dielectrics, barium titanate was promising material for ceramic capacitor. It was produced by specific formulation with various dopants-La2O3, ZrO2, SnO2, CaZrO3, CaTiO3, CaSnO3, Bi2O3, and etc.-according to demanded properties of capacitor. In this study, we would examinate the study of dielectric properties and temperatuer characteristics (T.C.) with the amount of Bi2O3. The sample was prepared with [BaTiO3]10＋[BaZrO3, SnO2, La2O3, ZrO2]10 and Bi2O3 varied from 1.0, 1.5, 2.0, 2.5 to 3.0wt%. After milling and mixing for 15hrs, each sample was dried and then pressed at 700kg/$\textrm{cm}^2$ into pellets. Pellets were fired at 131$0^{\circ}C$, for 3hrs in air. As the result of measurements, dielectric constant, break down voltage, and insulation resistance were increased with the amount of Bi2O3, and the resonant frequency was shifted from high frequency to low frequency range. In the case of temperature characteristics, capacitance change rate was symmetrically changed at -$25^{\circ}C$ and ＋85$^{\circ}C$ respectively. Therefore, it is recognized that the temperature characteristics can be moderated with doping Bi2O3 in our study.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.468-479
• /
• 2016

In order to supply power to online monitoring systems that are attached to high voltage catenary or overhead wires, a wireless power transfer system is required that is able to transmit power over the insulation gap. Such wireless power transfer systems have transmitter and receiver coils that have diameters of over 10cm. This paper focused on an investigation of the sources of loss in the coils when the coils are fabricated using printed circuit board technology. Using finite element simulation results, it has been shown that the dielectric loss in the substrate was the dominant source of the total loss. It has been demonstrated that the selection of a proper dielectric material was the most critical factor in reducing the loss. For further reduction of the loss, the distributed tuning capacitor method and the slotting of the inter-turn spaces have been proposed. For the evaluation of the proposed methods, four coils have been fabricated and their equivalent series resistances and quality factors were measured. Measured quality factors were greater than 300, which means that these devices will be helpful in achieving high coil-to-coil efficiency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.17-20
• /
• 1993

In this paper, the (1-x)($Sr_{0.50}$$Pb_{0.25}$$Ba_{0.25}$)$TiO_3$-x $Bi_2$$Ti_3$$O_{9}$(x=0,4,6,8[mol.%]) ceramics with paraelectric properties were, fabricated by mixed oxide method. The dielectric and structural properties of ceramics were studied with sintering temperature and addition of $Bi_2Ti_3O_{9}$, and the application for the high - voltage capacitor was investigated. In the specimens with sintering at 1350[$^{\circ}C$], sintered density was showed the highest value of 5.745[g/cm$^3$]. Increasing of sintering temperature, average grain size was increased. The specimen. ($Sr_{0.50}$$Pb_{0.25}$$Ba_{0.25}$)$TiO_3$sintered at 1350[$^{\circ}C$] showed good dielectric properties and breakdown voltage was showed the highest value of 200[kV]. Temperature coefficient of capacitance was stabilized in specimens added $Bi_2Ti_3O_{9}$ Sintered density. dielectric properties and breakdown voltage ware decreased with increasing the contents of $Bi_2Ti_3O_{9}$.

• Korean Journal of Materials Research
• /
• v.34 no.6
• /
• pp.283-290
• /
• 2024

The aggressive scaling of dynamic random-access memory capacitors has increased the need to maintain high capacitance despite the limited physical thickness of electrodes and dielectrics. This makes it essential to use high-k dielectric materials. TiO₂ has a large dielectric constant, ranging from 30~75 in the anatase phase to 90~170 in rutile phase. However, it has significant leakage current due to low energy barriers for electron conduction, which is a critical drawback. Suppressing the leakage current while scaling to achieve an equivalent oxide thickness (EOT) below 0.5 nm is necessary to control the influence of interlayers on capacitor performance. For this, Pt and Ru, with their high work function, can be used instead of a conventional TiN substrate to increase the Schottky barrier height. Additionally, forming rutile-TiO₂ on RuO₂ with excellent lattice compatibility by epitaxial growth can minimize leakage current. Furthermore, plasma-enhanced atomic layer deposition (PEALD) can be used to deposit a uniform thin film with high density and low defects at low temperatures, to reduce the impact of interfacial reactions on electrical properties at high temperatures. In this study, TiO₂ was deposited using PEALD, using substrates of Pt and Ru treated with rapid thermal annealing at 500 and 600 ℃, to compare structural, chemical, and electrical characteristics with reference to a TiN substrate. As a result, leakage current was suppressed to around 10^-6 A/cm² at 1 V, and an EOT at the 0.5 nm level was achieved.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.72-74
• /
• 2014

Multilayer ceramic capacitor (MLCC) makes acoustic noise of electronic devices. Conversed piezoelectric effect of dielectric substance consists of $BaTiO_3$ causes vibration of MLCC so it must be analyzed to reduce the noise. Thus, finite element model for piezoelectric analysis of MLCC was constructed in this paper. Piezoelectric characteristics of MLCC was considered for the accurate simulation result. Displacement response for sinusoidal voltage signal was measured and simulation result was verified with test result.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.321-324
• /
• 1999

This paper was presented to BaTiO$_3$-SrTiO$_3$(BST) ceramic capacitor in using high voltage. Structural and electrical properties of BST ceramic capacitor were researched in accordance with SrTiO$_3$ contents. As the result of investigation, the BST1 ceramic capacitor was showed to stable dielectric properties between 25 and 85[$^{\circ}C$]. According as frequency was increased, relative permittivity was decreased because inner spontaneous polarizations were decreased. As supplied voltage was increased, relative permittivity of specimen was varied in 3.04 ~3.98[%].

• ETRI Journal
• /
• v.38 no.5
• /
• pp.879-884
• /
• 2016

In this paper, an ultra-small marker beacon antenna operated in the VHF-band is proposed. This antenna has a modified linear IFA structure with a lumped capacitor and a capacitive plate for frequency tuning and impedance matching. The capacitive plate is directly connected to the end of a linear radiator and is separated from the antenna ground by 1 mm. The main operating frequency is mainly controlled by the size and dielectric constant of the capacitive plate. The lumped capacitor is useful for fine frequency tuning. Using the proposed structure, an ultra-small marker beacon antenna can be realized with a length of 0.04 ${\lambda}_0$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.270-270
• /
• 2007

전자 산업의 발달로 인해 전자기기에 소형화, 경량화 및 다기능화가 요구되면서 민쇄회로기판(PCB)에도 고밀도화, 고집적회가 필요하게 되었다. 이에 따라 embedded passive 기술을 이용하여 기판 내부에 가능한 많은 수동소자들을 실장시키려는 노력이 진행되어지고 있다. 가장 수요가 많은 capacitor의 경우 부피와 전기적 특성 측면에서 내장 효과가 가장 큰 passive 소자에 해당한다. 본 연구에서는 내장형 capacitor의 유전재료로서 중요한 $BaTiO_3$ powder를 filler로 사용하여 epoxy/BT 복합체에서 filler의 분율에 따른 유전상수률 측정하고, filler의 열처리에 따른 유전상수의 변화를 관찰하였다. 그러고 이들 복합체의 mixing rule과 미세구조 관찰을 통하여 기판용 RCC 소재로서의 적용성을 평가하고자 하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.8
• /
• pp.1471-1475
• /
• 2007

In this paper, a novel embedded ultra wideband (UWB) band-pass filter is presented on a FR-4 package substrate including high Dk resin coated copper (${\varepsilon}_r=30$) film. The proposed UWB filter is comprised of a parallel resonator with meander-type uniform impedance resonator (UIR) and two series resonators with high Q circular stacked spiral inductor and metal-insulator-metal (MIM) capacitor. In order to obtain excellent attenuation characteristics by generating attenuation poles in lower and upper stop bands, a single MIM capacitor is added to each resonator. The fabricated FR-4 embedded UWB filter has insertion loss of -1.0dB and return loss of -11dB, respectively. It has also extremely wide bandwidth (over 50%) and small size ($3.7{\times}4{\times}0.77\;mm^3$) which is compatible with LTCC devices.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.5
• /
• pp.210-213
• /
• 2005

The $BaTiO_3/SrTiO_3$ heterolayered thick films were fabricated by the screen printing method on alumina substrates. The effect of the sintering temperature on the microstructure and dielectric properties of the $BaTiO_3/SrTiO_3$ thick films has been investigated. The relative dielectric constant and dielectric loss at 1 MHz of the $BaTiO_3/SrTiO_3$ heterolayered thick films with sintering temperature of $1350^{\circ}C$ were about 751 and 1.74, respectively. The remanent polarization $(P_r)$ of the pure $(Ba_{0.5}Sr_{0.5})TiO_3$ and $BaTiO_3/SrTiO_3$ heterolayered films are approximately $5.1\;{\mu}C/cm^2$ and $10\;{\mu}C/cm^2$. This study suggests that the design of the $BaTiO_3/SrTiO_3$ heterolayered thick films capacitor with different phase should be an effective method to enhance the dielectric and ferroelectric performance in devices.