• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.33-36
• /
• 1999

In this paper, $Ba_{0.5}$Sr$_{0.5}$TiO$_3$ thin-films were prepared on Pt/Ti/Si0$_2$/Si substrates by RF magnetron sp-uttering method. We investigated electric and dielectric properties of BST thin-films with various ann-ealing temperature using in-sute RTA. Deposition conditions of BST films were set substrate temperat-ure, 30$0^{\circ}C$ and working gas ratio, Ar:O$_2$=90:10. After BST films deposited, we fabricated a capacitor of MIM structure with Al top electrode for measurement. Post-annealing using RTA performed at 40$0^{\circ}C$, $600^{\circ}C$, 80$0^{\circ}C$ for 60 sec, respectively. Also we exacted crystallization and composition of BST thin-films by XRD analysis. In measurement result, this capacitors showed a dielectric constant of about 200 at 1MHz and leakage current density of 5$\times$10$^{-8}$ A/$\textrm{cm}^2$ at 1.5V Microstructure of BST thin-films exhibited effective quality in low-temperature annealed 71ms than high-temperature annealed 71ms.s.s.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.128-128
• /
• 2002

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.358-358
• /
• 2010

To improve the programming/erasing speed and leakage current of multiple dielectric stack tunnel barrier engineering (TBE) Non-volatile memory, We propose a new concept called staggered structure of TBE memory. In this study, We fabricated staggered structure capacitor on $Si_3N_4$ stacked HfAlO and measured C-V curve that can observe tunneling characteristic of this device as various annealing temperature compared with that of single layer $SiO_2$ capacitor.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1355-1356
• /
• 2007

SMD type 압전레조네이터 제작을 위한 압전 조성물을 찾고자 PLT 세라믹스에 B-site Ti 자리에 Mn을 치환시키고 소결첨가제로서 CuO를 첨가하였다. $0{\sim}0.4wt%$ CuO를 첨가하여 1150, 1200, $1250^{\circ}C$로 각각 소결한 후 소결온도 및 CuO 첨가량에 따른 압전 및 유전특성을 관찰하였다. CuO 첨가량에 따라 1150, $1200^{\circ}C$ 소결시 밀도가 증가하였고, $1250^{\circ}C$ 소결시 기계적 품질계수가 증가하였다. 소결온도 $1250^{\circ}C$, 0.1wt% CuO 첨가시 밀도, 전기기계 결합계수(kp), 유전상수, 기계적 품질계수는 7.5[g/cm3], 0.1, 253, 1776을 각각 나타내었다.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.839-843
• /
• 2019

This paper demonstrates a variable capacitor using fluids as dielectric material and investigates the possibility of its application to a magnetic resonance microscopy's coil. The capacitor structure was integrated with a microfluidic channel and the capacitance was measured while changing the filling percentage of fluids in the channel. The measured capacitance when filling DI water and mineral oil was changed from 1.7 pF to 12 pF and from 1.7 pF to 2 pF, respectively.

• Journal of the Korea Safety Management & Science
• /
• v.23 no.3
• /
• pp.103-113
• /
• 2021

As the use of capacitors in electrical appliances and electrical control circuits increases, the related electrical fire is increasing. There are various parts such as resistors, coils, and capacitors that make up an electric circuit. Among them, the ignition of a capacitor with a temporary charging function is closely related to the structural characteristics of the capacitor. Capacitors can explode due to various reasons, and the high heat generated when they explode ignites the inflammable dielectric, which in turn burns the inflammable materials such as the surrounding electric wires and spreads into a fire. In this paper, the ignition mechanism is studied by conducting a reenactment experiment on the various probabilities that can be ignited in an electric capacitor, and the prevention measures to be applied to the fire prevention are presented.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.685-689
• /
• 2005

In the fabrication and design of MLCCs (Multilayer Ceramic Capacitors) with Ni inner electrode for medium and high voltage, reliability and dielectric breakdown mode have been investigated. For thickness of green sheet, the relationship between the rated voltage versus the thickness of green sheet. Increasing the thickness of green sheet increases the dielectric breakdown voltage. However, a practical limit to this linear relationship occurs at 30 urn and above. As the thickness of green sheet increased, dielectric breakdown voltage and weibull coefficient is increased, but abruptly decrease at 30 urn and 36 urn. When 24 urn of green sheet thickness, weibull coefficient and dielectric breakdown voltage were 13.58 and 70 V/um respectively. The results enabling the MLCCs to demonstrate high levels of reliability at medium and high voltage.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.696-699
• /
• 2003

In this study, we suggested the model to precisely evaluate the ferroelectric hysteresis loop, using the modified Sawyer-Tower circuit and the ferroelectric capacitor with a MDFM(Metal-Dielectric-ferroelectric-Metal) structure. The mathematical expression of dipole polarization is applied to the numerical integration algorithm, and the fatigue property can be considered including the dielectric layer between ferroelectrics and bottom electrode. The validity of our model is proved comparing the estimated value of our model and the measured results of PLT(10) thin film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.53-56
• /
• 2008

The commercial parallel plate electrodes system with guard-ring electrode have been widely used for measurement of dielectric constants of solid materials. And the specification of the electrodes system is about 1 % of measurement uncertainty. This measurement uncertainty is only estimated the error come from mechanical measurements such as the area of the electrodes and the gap between the electrodes except the error come from the air gap between the electrodes and dielectric specimen. Because it is impossible to measure the air gap. This study analyze the total measurement uncertainties of the commercial dielectric constant test cell using 3 kinds of Standard Reference Materials. As a results, the total measurement uncertainty is much bigger than 1 % and the most of the uncertainty can be reduced by compensation of the error values evaluated in this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.611-615
• /
• 2003

The crystalline and dielectric properties on $Al_2O_3$ filled glass frit ($CaO-Al_2O_3-SiO_2-MgO-B_2O_3$) with admixtures of $TiO_2$ have been investigated. The dielectric constant value of $7.5{\sim}7.8$, quality factor value of 700 were obtained for glass frit : $Al_2O_3$ (50 : 50 wt%) ceramics. As the amount of $TiO_2$ increased, temperature coefficient of dielectric constant were decreased.