• Design & Manufacturing
• /
• 제11권1호
• /
• pp.19-25
• /
• 2017

A conventional taped banknotes detecting device in the banknote counting machine have some problems caused by temperature, humidity, dust and other environmental conditions. In order to the improve the detection performance of taped banknote in the banknote counting machine, we developed taped banknotes detecting device that the ultrasonic wave sensor was replaced by mechanical method device. There are many factors for the performance of the taped banknote detecting device of a mechanical method, we considered three main factors that are the amplification ratio of the thickness of banknotes, the pressing force of banknotes and the feeding speed of banknotes. We carried out the experiments with the 27 kinds of combination of these three main factors. As the result, accurate detection was possible to the normal banknotes and taped banknotes regardless of the feeding rate in terms of the amplification rate 27 times and the pressing force 660gf.

• 한국정밀공학회지
• /
• 제27권12호
• /
• pp.67-74
• /
• 2010

The fabrication method of aspheric lens is changed from machining to press molding so as to improve the productivity. In the case of the press molding method, the temperature control of the molding die is most impotent, because the temperature of each molding die determines the quality of lens. But any practical method for direct measuring of the lens temperature and the die internal temperature is yet unknown. Besides, in the case of the press molding system in which the heating and pressing and cooing of a die is done at one work station, the cycle time for the system is yet too long. The paper shows an improved structure of radiant sequential system in which the heating and pressing and cooing of dies is done at individual work station so as to cut down the cycle time. To know the die internal temperature, numerical results are given using ANSYS. An experimental radiant sequential system is developed and tested. Finally, the Taguchi method is applied in order to optimize the setting conditions of individual work station.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 고액공존금속의 성형기술 심포지엄(III) SYMPOSIUM ON SEMISOLID FORMING TECHNOLOGY(III)
• /
• pp.15-32
• /
• 1999

A relationship between stress and stain is very important to design a die to avoid defects of products during semi-solid forming process. Since the liquid will be of eutectic composition in alloys liquid segregation will result in significant or undesirable situation. The materials used in this experiment are A 357. A390, Al2024 alloys that is fabricated by the electro-magnetic stirring process from Pechiney in France. The compression test was performed by induction heating equipment and MTS. In order to prevent the liquid segregation these measured temperature would be useful to control of strain rate during compression test. The liquid segregation is controlled as change of the strain rate and solid fraction during the compression process, The characteristics of flow between solid and liquid phase considering liquid segregation is examined through the above experiments. In the case of medium and high volume fractions of solid the distribution of strain rate is calculated by using compression test data of semi-solid materials (SSM). The thixoforming experiments with the designed die are carried out successfully. The die filling patterns of SSM for variation of die temperature and pressing force have been investigated. The hardness of the thixoformed scroll products is evaluated in terms of the microstructure for each position.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.507-512
• /
• 2003

A finite element analysis for near-net-shape forming of Al6061 powder was performed under warm pressing. The advantages of warm compaction by rubber isostatic pressing were discussed to obtain parts with better density distributions. To simulate densification and deformed shape of a powder compact during warm pressing, the elastoplastic constitutive equation based on yield function of Shima-Oyane was implemented into a finite element program(ABAQUS). The hyperelastic constitutive equation based on the Ogden strain energy potential was employed to analyze nonlinear elastic response of rubber. Finite element results were compared with experimental data for Al6061 powder compacts under warm pressing.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.255-258
• /
• 2003

In this study, to develop a flash-less die for forming of shoe-outsole, experiments and forming analysis were carried out. In order to reduce the extra-materials, of feet method and mass distribution method are used in the preform design. To improve the accuracy of contact surface of dies, the contact status of dies are measured by using the pressure film. The vertical pressing die structure and the guide-gutter system have been developed for the discharge of extra-materials and re-pressing. By the investigation, flash of shoe-outsole was considerably reduced.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1751-1758
• /
• 2001

Among severe plastic deformation processes, ECAP has drawn much attention due to its advantages including ultra-fine grain size material production. In this paper, ECAP process with pure -Zirconium is investigated due to its applicability to nuclear reactors. The finite element method is employed to investigate the deformation behavior of materials during ECAP process. In particular, effects of process parameters such as die deformation and channel angles on the material behaviors have been investigated. Experimental studies have also been performed to verify the numerical results.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.785-792
• /
• 2011

Equal channel angular(ECA) pressing is the established processing technique in which a polycrystalline metal is pressed through the die to achieve a very high plastic strain. Therefore, the capability to produce an ultra-fine grain size in the materials is provided. To investigate that mechanical properties at elevated temperature have the ultrafine grain ECA pressing, experiments were conducted on an Al-4.8% Mg-0.07% Mn-O.06% Si alloy. After having been solution treated at 773K for 2hrs, the billet for ECA pressing was inserted into the die. And it was pressed through two channel of equal to cross section intersecting at a 90 degree angle. The billet can be extrude repeatedly because of 1:1 extrusion ratio. Since the billet is passed through the cannel for 2 times, a large strain is accumulated in the alloy. The tensile tests on elevated temperature were carried out with initial strain rate of $10^{-3}s^{-1}$ at eight temperature distributed from 293K to 673K.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.747-753
• /
• 2000

There has been a number of investigations in recent years reporting the results obtained on the structure and properties of metals deformed to severe plastic deformation (SPD). Being deformed to SPD, ultra-fine grains (UFG) are usually formed, and UFG structure exhibits fundamental differences in original physical properties. One method often used to obtain SPD is equal channel angular pressing (ECAP). In order for this technique to be exploited, it is important to understand the deformation behavior during the ECAP processing and relationship to the configuration of die. The finite element method (FEM) has been used to investigate this issue. It has been found that the plastic deformation is sensitive to the channel angle and material properties and is not uniform across the width of the specimen and the pressing load is relative to deformation during the ECAP processing.

• 대한기계학회논문집A
• /
• 제27권7호
• /
• pp.1076-1086
• /
• 2003

The effect of a rubber mould on densification behavior of aluminum alloy powder was investigated under cold isostatic compaction. A thickness of rubber mould and friction effect between die wall and rubber mould were also studied. The hyperelastic constitutive equation based on the Ogden strain energy potential was employed to analyze deformation of rubber. The elastoplastic constitutive equation of Shima and Oyane and that of Lee on densification were implemented into a finite element program (ABAQUS) to simulate densification of metal powder for cold isostatic pressing and rubber isostatic pressing. Finite element results were compared with experimental data for densification and deformation of aluminum alloy powder under isostatic compaction.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.467-468
• /
• 2007