• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.8
• /
• pp.72-79
• /
• 2008

To meet demand of big capacity and high speed rotation for washing machine, more stress from bending and twisting are complexly loaded onto the shaft supporting the horizontal drum, causing problems in fracture strength and fatigue life. Shafting system is mainly divided into flange and shaft. Shaft and flange connected by inserting shaft serration into flange on the process of die casting. When the system is operating, the gap is formed between serration and flange. But, Serration has various design factors and the optimal values can't be easily determined. Using a design of experiment (DOE) based on the FEM (Finite Element Method), this study was performed investigating the interaction effect between the various design factors as well as the main effect of the each design factor under bending, twist and vibration and proposed optimum design using box-behnken method among response surface derived from regression equation of simulation-based DOE.

• Transactions of Materials Processing
• /
• v.14 no.1 s.73
• /
• pp.57-64
• /
• 2005

This study deals with the cold forging process design for shaft in the main part of automobile motors with rectangular deep groove. In forging process, the accuracy and die lift is very important because it have influence on reduction of the production cost and the increase of the production rate. Therefore, it is necessary to develop the manufacturing process of shaft by cold forging., process variables are the cropped face angle of billet and the eccentric load of punch. The former is derived from cropping test, the latter is occurred by clearance between container and preform. Also, grooved preform select the process variable for decrease in punch deflection. We investigate that a deflection of punch and a deformation of preform to every process variables. Through this investigation, we suggest the optimal preform and process design, expect to be improved the tool life in forging process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.956-959
• /
• 2001

In die and mould industry, major material such as cemented carbide is broadly used for increasing the life time and decreasing the cost. It is also required the development for the skills of wire-cut electrical discharge machining(WEDM), but the WEDMed surface was found to be worst due to the attached components of wire. Precision machining method like lapping is necessary for obtaining high quality surface. The lapping compound such as Al2O3 and SiC and cast iron lap can be used for lapping process. The components of Cu and Zn were found WEDMed surface of the specimen. As the result, the low quality of precision was obtained and the heat damage layer of the specimen was occurred. The value of surface hardness was deteriorated, and therefore finish process was required.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.5
• /
• pp.67-74
• /
• 2004

Laser heat treatment is an effective technique used to improve the tribological properties and also to increase the service life of automobile components such as camshafts, crankshatfs, lorry brake drums and gears. High power $CO_2$ lasers and Nd:YAG lasers are employed for localized hardening of materials and hence are of potential application in the automobile industries. The heat is conducted rapidly into the bulk of the specimen causing self-quenching action to occur and the formation of matrensitic structure. In this investigation, the microstructrual features occurring in Nd:YAG laser hardening SM45C and $STD_11$ steel are discussed with the use of optical microscopic and scanning electron microscopic analysis. Moreover, This paper describes the optimisation of the processing parameters for maximum hardened depth of SM45C and $STD_11$ steel specimens of 10mm thickness by using CW:YAG laser.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.191-197
• /
• 2007

Inclined surface milling in the mould and die industries is one of the most commonly needed cutting process. For the variety and complexity of cutting characteristics in various cutting condition, it is difficult to select a optimal tool path orientation. Especially, when the cutting process becomes unstable, it induces self-exited vibrations, a frequent cause of poor tool life, rough surface finish, damage to the workpiece and the machine tool itself, and excessive down time. The comparative results through FFT analysis in this study provide a guideline for the selection tool path orientation.

• The Korean Journal of Rehabilitation Nursing
• /
• v.1 no.1
• /
• pp.43-50
• /
• 1998

The literature review for fall in the elderly has been done for the better quality of life of increasing elderly people toward 21 st century. Because 30 to 50% of over sixty five years old persons have experiences of fall, five percent of the fallen have trauma such as bone fracture requiring hospitalization and three quarter of people who die as fall are over 65 year old, fall is important health problem of them. There are very little societal interest in and research related to fall. Therefore, among recent foreign and our literatures studying literature review of frequency of fall, risk factors and assessing method for tall, and the management of fall prevention program, I would like to find research direction. Conclusivelly, we should study extensively the survey of the elderly's fall and on the basis of it. developing fall prevention program, promote the elderly's health through fall prevention.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.171-177
• /
• 1995

In this paper, the deformation method for inner and outer races of rollr-bearing bymeans of the warm precision forging is investigated. We adapted the process designsuch as following that, toincrease Die life, reduce heat transfer through conduction and the eccentricity of preform in warm forging of bearing gace, the bottom portion of billet is formed during upsetting process. Then it is backward extruded, and thus obtained ring preform is formed by combined extrusion. Also, we compared it with the froming method in China and Japan, and we have known it is more excellent method. Basides, this forming method is simulated by UBST which is based on the merits of UBET nd FEM. The results show that it is easy to know the exact location of neutral surface through the inspection of streamline during combined extrusion, and the velocity vector distribution along the surface of velocity discontinuity is investigationed. Also the effectiveness of this method is proved by te experiment using model material that is Plasticine.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.471-478
• /
• 2000

Endmill is one of the most important cutting tool, not only for machining of mold and die, but also for manufacturing of car industrial. Futhermore with spindle speeds on the increase and machined-surface quality aspiring to higher levels. The purpose of this study is an analysis of endmill's rake angle for appropriate tools design and making for the high speed machining. In this study, Experimental works are also executed to measure shape of endmills, cutting force, on different shape of endmills. Finally, To get concept of endmill design, Tool life was experimented on various design of tool from this study.

• Proceedings of the KAIS Fall Conference
• /
• 2006.05a
• /
• pp.196-199
• /
• 2006

프레스금형의 부품 중에서 펀치와 다이플레이트를 제작하는데 주로 W-EDM을 이용한다. W-EDM전에는 기계가공으로 제작된 펀치와 다이플레이트로 제품을 생산하게 되면 생산량이 200만${\sim}$230만개를 생산하고 금형수명을 다하였다. 그러나 W-EDM으로 제작된 금형으로 제품을 생산하게 되면 생산수량이 70만${\sim}$80만개를 생산하고 금형수명이 다하였다. 이것은 W-EDM한 후에 발생되는 가공변질층에 기인하는 것으로 사료되므로 W-EDM전과 W-EDM후의 가공면에 대한 SEM촬영을 실시하여 가공변질층의 발생을 확인하고 이에 대한 제거방법을 연구하였다.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.129-133
• /
• 2008

As a rotating machine element, plastic gears are more and more widely used in such as industrial machine element, since plastic gear is lighter, higher wear-resistance, and higher vibration absorbing ability than metal gears. When operating plastic parts, tooth breakage and fatigue life shortened due to increasing number of applying load and tooth flank temperature rising, such that accuracy of plastic gears is divided from allowable range to cause vibration and noise. On this study, a internal plastic gears are developed which improved the filling balance molding process by a new injection mold structure. The new mold structure called HR3P(hot runner type 3plate mold). As the result from this studies, we obtained a very accurate roundness internal gears by using design of experiment.