• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.567-572
• /
• 2009

The densification behaviors of mixtures of copper and steel powders during cold die compaction were investigated. We proposed the pressure-dependent yield function based on the rule of the mixtures of each yield function of a critical relative density type. The constitutive equations were implemented into a finite element program (DEFORM2D) to analyze the densification and deformation behavior of powder mixtures, and the simulated results are in good agreement with the experimental results in reference studies.

• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.104-111
• /
• 2011

An ultrafine grained Mg-9Al-1Zn magnesium alloy with the mean grain size less than $1{\mu}m$ was produced by using high-ratio differential speed rolling. The processed alloy exhibited excellent superplasticity at relatively low temperatures. The micro-forming tests were carried out using a micro-forging apparatus with micro V-grooved shaped dies made of silicon and the micro-formability was evaluated by means of micro-formability index, $R_f$ ($=A_f/A_g$, $A_f$: formed and inflowed area into the V-groove, $A_g$: area of the V-groove). The $R_f$ value increased with temperature up to $280^{\circ}C$ and then decreased beyond $300^{\circ}C$. The decrease of the $R_f$ value at $300^{\circ}C$ was attributed to the accelerated grain coarsening. Increasing the micro-forging pressure increased the $R_f$ values. At a given die geometry, die filling ability decreased as the die position moved away from the die center to the end. FEM simulation predicted this behavior and a method of improving this problem was proposed.

• 소성∙가공
• /
• 제11권2호
• /
• pp.171-178
• /
• 2002

The elastic deflections of the cold forging die influence the dimensional accuracy of forged parts. The die dimension is continuously changed during the loading, unloading, and ejecting stage. In this paper, we evaluated the elastic deflections of cold forging die during the loading, unloding and ejecting stage with experimental and FEM analysis. Uni-axial strain gages are used to measure elastic strain of die during each forging stage. Strain gages are attached un the upper surface of die. A commercial F.E.M. code, DEFORM$-2D^{TM}$ is used to predict the elastic strains of die, to be compared those by experiments. Two modelling approaches are used to define the reasonable analysis method. The first of the two modelling approaches is to regard the die as rigid body over forging cycle. And then, the die stress is analyzed by loading the die with pressure from the deformed part. The other is to regard the die as elastic body from forging cycle. The elastic strain of tool is calculated and the tool is elastically deformed at each strep. The calculated results under the elastic die assumption are well agreed wish experimental data using the strain gages.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.28-33
• /
• 2013

During the cold forming, due to high working pressure acting on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The mechanisms of wear are consisted of adhesion, abrasion, erosion and so on. Die wear affects the tolerances of formed parts, metal flow, and costs of process. The only way to control these failures is to develop a prediction method on die wear suitable in the design state in order to optimize the process. The wear system is used to analyse 'operating variables' and 'system structure'. In this study, with AISI D2, AISI 1020, AISI 304SS materials, a series of the wear experiments of pin-on-disk type to obtain the wear coefficients from Archard's wear model and the upsetting processes are carried out to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes are performed by the rigid-plastic finite element method. The result of the analysis is used to investigate the die wear the processes, and the analysis simulated die wear profiles are compared with the experimental measured die wear profiles.

• 소성∙가공
• /
• 제29권6호
• /
• pp.362-369
• /
• 2020

In this study, elastoplastic finite element analysis with multi-body treatment was used to elucidate the mechanical phenomena occurring from pre-stressing of die-system. A finite element analysis model with detailed conditions is proposed. The effects of die pre-stressing slope on the circumferential components of the pre-stressed die inserts were evaluated. The role of tight fitting between the supporter and die case was also emphasized because it has a significant effect on the undesirable change in the target slope of machined inner surface of the die case around the die insert. The two mechanical problems include the one between die-insert and die case and the other between supporter and die case, and their correlation is minimized to establish the optimum design in the die structural design stage because it cannot be quantitatively controlled owing to various factors affecting the die structural behavior during die pre-stressing.

• 한국주조공학회지
• /
• 제28권3호
• /
• pp.119-123
• /
• 2008

Wear test on two die steels for aluminum die casting was carried out by dipping and rotating the specimens into the molten aluminum maintained $680^{\circ}C{\sim}780^{\circ}C$. The rotating speed of the specimen was $4.5rpm{\sim}20.0rpm$. Diffusion layer was formed between the die steel and molten aluminum, and became thicker with dipping time. Wear rate was not proportional with the thickness of the diffusion layer, but was closely related to the density of the diffusion layer. Wear rate was little affected by the kind of die steel and by the microstructure such as martensite, tempered martensite, and pearlite. Specimen with nitrided surface showed good wear resistance, and its wear rate was decreased with increase in the thickness of nitrided layer. While whole surface was worn in heat treated specimens, wear of nitrided specimens was proceeded by pitting partially.

• 한국재료학회지
• /
• 제22권4호
• /
• pp.169-173
• /
• 2012

Recently, various attempts to produce a heat sink made of Al 6xxx alloys have been carried out using die-casting. In order to apply die-casting, the Al alloys should be verified for die-soldering ability with die steel. It is generally well known that both Fe and Mn contents have effects on decreasing die soldering, especially with aluminum alloys containing substantial amounts of Si. However, die soldering has not been widely studied for the low Si aluminum (1.0~2.0wt%) alloys. Therefore, in this study, an investigation was performed to consider how the soldering phenomena were affected by Fe and Mn contents in low Si aluminum alloys. Each aluminum alloy was melted and held at $680^{\circ}C$. Then, STD61 substrate was dipped for 2 hr in the melt. The specimens, which were air cooled, were observed using a scanning electron microscope and were line analyzed by an electron probe micro analyzer. The SEM results of the dipping soldering test showed an Al-Fe inter-metallic layer in the microstructure. With increasing Fe content up to 0.35%, the Al-Fe inter-metallic layer became thicker. In Al-1.0%Si alloy, the additional content of Mn also increased the thickness of the inter-metallic layer compared to that in the alloy without Mn. In addition, EPMA analysis showed that Al-Fe inter-metallic compounds such as $Al_2Fe$, $Al_3Fe$, and $Al_5Fe_2$ formed in the die soldering layers.

• 한국산학기술학회논문지
• /
• 제11권2호
• /
• pp.420-425
• /
• 2010

온간단조(warm forging) 가공은 가공소재(Billet)를 $800^{\circ}C$ 정도로 가열하여 금형의 다이블록 임프레션(impression) 상면(上面)에 위치결정 시켜 단조하고 있는데, 이 단조가공 과정에서 산화스케일의 비산에 따른 작업자의 화상에 대한 위험도와 산화스케일이 다이블록의 임프레이션에 부착 되거나 열처리기술 미흡으로 금형수명(die life)을 단축시키며 다이블록 안에 분무하는 이형제는 유해먼지, 유해증기, 미스트, 퓸, 악취 등을 발생시켜 작업장 환경을 오염시킴으로써 직무기피 직종으로 분리되기 때문에 생산량 목표 달성에 큰 문제점으로 대두 되고 있다. 더욱이 다이블록의 임프레이션 마멸부위를 수리보수하기 위한 재생공법의 미흡으로 납기지연, 금형비 상승의 요인으로 나타나므로 이에 대한 재생공법 개선과 작업장의 공해물 제거장치의 개발이 요망되고 있다. 본 연구에서는 황동제 관 이음쇠의 온간단조가공에서 도출된 빌릿가열시 문제점, 금형재생 보수시 문제점, 제조원가의 상승요인 등을 외국의 기술과 비교하여 온간단조 금형제작방법개선, 금형재생보수공법 개선, 유해가스 제거장치를 도입하여 환경친화형 작업장 개선 등으로 문제점을 해결 하고자 하였다.

• 소성∙가공
• /
• 제31권6호
• /
• pp.376-383
• /
• 2022

The potential damage region of a WC-Co cemented carbide die is investigated for cold forging process of a wheel-nut by numerical simulation with its chemical composition considered. Numerical simulation is utilized to calculate internal stress, especially for the WC-Co die, during the forging process. Finite element model is established, in which the elasto-plastic properties are applied to the work-piece of bulk steel, and elastic properties are considered for the lower die insert of the WC-Co alloy. This stress analysis enables to distinguish the potential damage regions of the WC-Co die. The regions from calculation are comparatively analyzed along with the crack area observed in the die after repetitive manufacturing. Effect of chemical composition of the WC-Co is also evaluated on characteristics of potential damage region of the die with variance of mechanical properties considered. Derived from Mohr-Coulomb fracture model, furthermore, a new stress index is presented and used for die stress analysis. This index inherently considers hydrostatic pressure and is then capable of deducing wide range of its distribution for representing stress state by modification of its parameter implying pressure sensitivity.

• 소성∙가공
• /
• 제31권2호
• /
• pp.51-56
• /
• 2022

In this study, finite element analyses were performed by applying a stress ring and split die design to relieve the tensile stress acting on the die due to high surface pressure during warm-closed forging. The applied material was a yield-ratio-control-steel (YRCS). It was used without quenching or tempering after forging. In the case of stress rings design, the number of stress rings and the tolerance for shrink fit were different. Vertical and horizontal splits were applied for insert die split design. Case 5 die with three stress rings, 0.2 % shrink fit tolerance, and vertical split was selected as an effective die design for tensile stress reduction. Based on die stress reduction analyses, Case 5 die for warm-closed forging was produced and smooth forgeability was secured, making it possible to manufacture forging product of yoke with the required geometry. In addition, controlled cooling using warm forging heat was applied to secure mechanical properties of yokes. When oil cooling was used for direct controlled cooling after warm-closed forging, a relatively uniform Rockwell hardness distribution and high mechanical properties could be obtained.