• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.66-69
• /
• 2016

In this paper, we suggests a Ka-band LNB considering next-generation UHD satellite TVRO. Since Ka-band has grater attenuation than Ku-band in atmosphere, we designed the low-noise down-converter to improve receiving sensitivity and to extend a dynamic range of receiver. It aims to compensate a quality of ultra high definition transmission signal for rainfall. The low-noise block diagram consists of a three-staged amplifier (LNA), band-pass filter for deleting image (BPF), mixer and IF when considering nonlinear characteristics in the receiver RF front end module. Also, we showed a LNB through optimization processes affecting dynamic range directly in receiver FEM. Asa resuly of experiment, the gain of low-noise down-converter show between 58.5dB and 60.7dB, the noise figure has a high characteristic as 1.38dB. Finally, the phase noise of local oscillator is -63.10dBc at 100MHz offset frequency.

• Journal of Digital Convergence
• /
• v.17 no.4
• /
• pp.137-147
• /
• 2019

This paper studies the effect of content information quality of u-tourism information system on flow theory and satisfaction. The purpose of the research is to generate and propose flow-related information to satisfy tourists with content information quality. The meaning of this paper is to derive success factors for verifying satisfaction of content information quality to tourists, establish hypotheses as research models, and evaluate verification. The differentiation of this study is the design implementation of u-fusion tourism information system by combining flow relation information with flow theory. The contribution of this paper is the generation of flow related information and the elicitation of success factors of contents quality of u-tourism information system. The advantage is that tourists can be patterned by symbolization and the pattern can be illustrated. The limitations of this paper are limited to small areas, and the lack of objectivity is required and future tasks are needed to compensate for them.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.523-546
• /
• 2022

Morphotropic phase boundary (MPB), which is a special boundary that separates two or multiple different phases in the phase diagram of some ferroelectric ceramics, is an important concept in identifying physics that includes piezoelectric responses. MPB, which had not been discovered in organic materials until recently, was discovered in poly(vinylidene fluoride-co-trifluoroethylene (P(VDF-TrFE)), resulting from a molecular approach. The piezoelectric coefficient of P(VDF-TrFE) in this MPB region was achieved up to -63.5 pC N^-1, which is about two times as large as the conventional value of -30 pC N^-1 of P(VDF-TrFE). An order-disorder arrangement greatly affects the rise of the piezoelectric effect and the ferroelectric, paraelectric and relaxor ferroelectric of P(VDF-TrFE), so the arrangement and shape of the polymer chain is important. In this review, we investigate the origin of negative longitudinal piezoelectric coefficients of piezoelectric polymers, which is definitely opposite to those of common piezoelectric ceramics. In addition to the mainly discussed issue about MPB behaviors of ferroelectric polymers, we also introduce the consideration about polymer chirality resulting in relaxor ferroelectric properties. When the physics of ferroelectric polymers is unveiled, we can improve the piezoelectric and pyroelectric properties of ferroelectric polymers and contribute to the development of next-generation sensor, energy, transducer and actuator applications.

• Journal of the Korea Society for Simulation
• /
• v.18 no.4
• /
• pp.67-79
• /
• 2009

Because a product in the car industry has a short life cycle in recent years, the process planning and the manufacturing lines have to be changed frequently. Most of time, repositioning an existing facility and modifying used control information are faster than making completely new process planning. However, control information and control code such as PLC code are difficult to understand. Hence, industries prefer writing a new control code instead of using the existing complex one. It shows the lack of information reusability in the existing process planning. As a result, to reduce this redundancy and lack of reusability, we propose a SOS-Net modeling method. SOS-Net is a standard methodology used to describe control information. It is based on the Device Structure which consists of sensor information derived from device hardware information. Thus, SOS-Net can describe a real control state for automated manufacturing systems. The SOS-Net model is easy to understand and can be converted into PLC Code easily. It also enables to modify control information, thus increases the reusability of the new process planning. Proposed model in this paper plays an intermediary role between the process planning and PLC code generation. It can reduce the process planning and implementation time as well as cost.

• Nuclear Engineering and Technology
• /
• v.27 no.4
• /
• pp.571-581
• /
• 1995

The generation, verification and validation of Emergency Procedures for Nuclear Power Plant is a difficult and complex process. Atomic Energy Control Board(AECB) requires that emergency procedure and plan be produced before obtaining the Operating License, that is, detailed plans and procedures to handle emergency situations for both on-site actions and off-site actions be developed. In this report Emergency Operating Procedures Standard for Canadian Nuclear Utilities which makes reference to U. S. practices and the current direction of emergency procedures for CAN-DU reactors are reviewed and compared based on scope(events covered), methodology (event-oriented or symptom-oriented or hybrid) and format(method of presentation) preponderantly, and an attempt is made to integrate these procedures and as a result the recommended strategy for Wolsong unit 2, 3, & 4 is presented as event-specific procedures, generic procedures(when event is not diagnosed) and whose format is combination of logic diagram and text.

• The Journal of Engineering Geology
• /
• v.28 no.3
• /
• pp.501-512
• /
• 2018

The acid leachate derived from the sulfide mineral such as pyrite can cause problems such as aging of infrastructure and environment contamination around the civil construction site. The purpose of this study is to assess the environmental effect of an acid leachate derived from pyrite in the Miryang area under road construction. In this study, 13 samples of situ core were used for the net acid generation (NAG) experiment. The chemical composition including pH, oxidation and reduction potential (ORP) and electrical conductance of water samples produced from the NAG test was analyzed. In additional, five polished thin sections of rock cores were made for electro microprobe analyses. In the results of the NAG tests, 7 samples showed lower values than pH 3.5. It strongly indicated that these areas are under the environmental and infrastructure damage by the acid leachate. The chemical type of the 7 samples was classified as the $Fe(Ca)-SO_4$ type, which is totally a different type compared to general groundwater. The concentration of total sulfur ranges from 0.004% to 12.5%. 6 rock samples are plotted on a potentially acid forming zone in the relation diagram between the total sulfide and NAG-pH. In conclusion, it is suggested that a protection method against an environmental demage and an infrastructure corrosions by the acid leachate should be prepared in all of areas under a road construction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.5
• /
• pp.1154-1163
• /
• 2008

DAS and SCADA system are main systems, which operate and manage the power system by using computer and communication technology. But DAS and SCADA have been operated independently in Korea, so there was some time delay in the fault handling and live-line work. To improve that problems, studies on the interface between DAS and SCADA have been needed. From November 2005 to December 2007, the pilot project has been performed in KEPCO's branch offices, as a result, direct method will be applied widely all over the country until 2010 because the operation information of substation users want can be transmitted fast and it is possible to control 43RC directly although the expense for direct method is about 1.3 times larger than that for web method. To improve problems revealed during the pilot project, substation object to object communication method is proposed and interface database automatic generation and interface system diagnosis and logging functions are developed. Interface data point and communication data type are defined, substation single line diagram automatic generation or manual editing function, SCADA monitoring and controlling function, log data managing function are developed in SCADA HMI program. It is expecting to reduce the average time for each outage about 33% and to improve the reliability, efficiency of operation, execution of DAS from automatic load transfer under a fault, and to contribute to export project.

• Clean Technology
• /
• v.29 no.3
• /
• pp.193-199
• /
• 2023

Biomass has been used to secure renewable energy certificates (REC) in domestic and overseas coal-fired power plants. In recent years, biofuel has been diversified from traditional wood pellets to non-woody biomass. Non-woody biomass has a higher content of alkaline metals such as K and Na than wood-based biomass, resulting in a lower melting point and an increase in slagging on boiler tubes, which reduces boiler efficiency. This study analyzed the effect of kaolin, an additive commonly used to increase melting points, on biomass co-firing to coal through thermochemical equilibrium calculations. In a previous experiment on biomass co-firing to coal conducted at 80 kW_th, it was interpreted that the use of kaolin actually increased the amount of fouling. In this study, analysis showed that when kaolin was added, aluminosilicate compounds were generated due to Al₂O₃, which is abundant in coal, and mullite was formed. Thus, it was confirmed that the amount of slag increased when more kaolin was used. Further analysis was conducted by increasing the biomass co-firing rate from 0% to 100% at 10% intervals, and the results showed non-linear liquid slag generation. As a result, it was found that the least amount of liquid slag was generated when the biomass co-firing rate was between 50 and 60%. The phase diagram analysis showed that high melting point compounds such as leucite and feldspar were most abundantly generated under these conditions.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.1-14
• /
• 2014

The expansion of the physical road in response to changes in social conditions and policy of the country has reached the limit. In order to alleviate congestion on the existing road to reconsider the effectiveness of this method should be asking. Currently, how to collect traffic information for management of the intersection is limited to point detection systems. Intelligent Transport Systems (ITS) was the traffic information collection system of point detection method such as through video and loop detector in the past. However, intelligent transportation systems of the next generation(C-ITS) has evolved rapidly in real time interval detection system of collecting various systems between the pedestrian, road, and car. Therefore, this study is designed to evaluate the development of an algorithm for queue length based real-time traffic signal control methodology. Four coordinates estimate on time-space diagram using the travel time each individual vehicle collected via the interval detector. Using the coordinate value estimated during the cycle for estimating the velocity of the shock wave the queue is created. Using the queue length is estimated, and determine the signal timing the total queue length is minimized at intersection. Therefore, in this study, it was confirmed that the calculation of the signal timing of the intersection queue is minimized.

• The Journal of the Petrological Society of Korea
• /
• v.14 no.3 s.41
• /
• pp.157-168
• /
• 2005

Trachytic rocks among the bimodal metavolcanic rocks of the Gyemyeongsan Formation and adjacent areas are investigated. Some rocks reveal very high content of iron and most rocks show very high abundances of rare earth elements and high field strength elements. Most rocks show significant Eu negative anomaly, which can be interpreted as the result of plagioclase fractionation. Lack of noticeable Nb negative anomaly indicates not-involvement of crustal material in their generation, which excludes the arc environment or remelting of continental crust from their genetic process. Metatrachytes of the Gymyeongsan Formation are plotted within the within-plate environment of the tectonic discrimination diagram utilizing immobile high field strength element Nb and Y. They also show typical characteristics of A-type magma, such as high Ga content. Considering their affinity to Al-type of Eby (1992) and their age of 750 Ma (Lee et al., 1998), they seem to have been produced by the differentiation of mantle-derived within-plate magmatism at the rift, related with the separation of Neoproterozoic supercontinent Rodinia. Possible connection of Gyemyeongsan and Munjuri Formations of the Okcheon metamorphic belt, at least part of them, to the Cathaysia block of South China during the Neoproterozoic is strongly suggested.