• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.190-196
• /
• 2014

Exhaust system by reinforcement of environment regulation came to the foe study necessity. And Exhaust system has necessary to increase the engine performance and silence. From this cause, Automobile has significantly considered production expense. this study makes process for checking the characteristics about Exhaust variable valve within muffler. Variable valve might reduce the baffle within muffler, It was possible to remove the front muffler. Therefor, To miniaturize a size of muffler might be increased by performance through cost-cutting effect and controling of back pressure. Because the Study on Variable valve installed within muffler, to measure the real data was hardly resulted one of the assignments. From manufactured conduct device, might measure data one of piece which was up-graded of problem. Considering to these point, stressed pressure distribution has analyzed on cross section, floating characteristics about velocity distribution around variable valve using analysis as computational fluid dynamics of Ansys with completed measurement data.

• Journal of the Korean Society of Visualization
• /
• v.19 no.2
• /
• pp.41-47
• /
• 2021

River and stream are the important water supply source in our lives. Eutrophication causes excessive green algae growth including microcystis, which makes harmful to ecosystem and human health. Therefore, the water purification process to remove green algae is essential. In Korea, green algae alarm system exists depending on the concentration of green algae cells in river or stream. To maintain the growth amount under control, green algae monitoring system is being used. However, the unmanned, small and automatic monitoring system would be preferable. In this study, we developed the 3D printed device to measure the concentration of green algae cell using microfluidic droplet generator and deep learning. Deep learning network was trained by using transfer learning through pre-trained deep learning network. This newly developed microfluidic cell counter has sufficient accuracy to be possibly applicable to green algae alarm system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.2
• /
• pp.135-145
• /
• 2004

An experimental study is conducted to investigate the flow and heat transfer characteristics of a multi-tube inserted impinging jet. Four different multi-tube devices are tested for various nozzle-to-plate distance. Flow visualization by smoke-wire method and velocity measurements using a hot-wire anemometer are applied to analyze the flow characteristics of the multi-tube insert impinging jet. The local heat transfer coefficients of the multi-tube inserted impinging jet on the impingement surface are measured and the results are compared to those of the conventional jet. In multi-tube inserted system the multi-tube length plays an important role in the flow and heat transfer characteristics of the jet flow. With multi-tube insert of I3d4 and I6d4 which has relatively longer tube length than the multi-tube-exit of I3d1 and I6d1, the flow maintains its increased velocity far downstream due to interaction between adjacent flows. For the small H/D of 4, the local heat transfer coefficients of multi-tube inserted impinging jet are much higher than those of the conventional jet because the flow has higher velocity and turbulent intensity by the use of the multi-tube device. At large gap distance of H/D=12, also higher heat transfer rates are obtained by installing multi-tube insert except multi-tube insert of I3d1.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.52-58
• /
• 2008

Ths paper describes the Dual-band switch which was proposed new structure that could improved the specification of broadband and designed by the optimized structure through simulation. The Dual-band switch with 2.4[GHz]/5.8[GHz] that can apply to 802.11a/b/g system that is commercialized present was studied to get a new structure with higher power, high isolation. The transmitter of switch was designed to operate a parallel switching element with stack structure of two FET. The receiver designed to have asymmetry structure that insert series FET in addition to basic serial/parallel FET. SPDT(Single Pole Double Throw) Tx/Rx FET switch is a device that can do switching from a port of input to two port of output. The fabricated SPDT switch has the characteristic of insertion loss of a below -3[dB] form DC to 6[GHz] and the isolation of a below -30D[dB](Rx mode).

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.29-35
• /
• 2016

We have demonstrated a $Ti:LiNbO_3$ electro-optic electric-field sensors utilizing a $1{\times}2$ Y-fed balanced-bridge Mach-Zehnder interferometric (YBB-MZI) modulator which uses a 3-dB directional coupler at the output and dipole patch antenna. The operation and design were proved by the BPM simulation. A dc switching voltage of ~16.6 V and an extinction ratio of ~14.7 dB are observed at a wavelength of $1.3{\mu}m$. For a 20 dBm rf power, the minimum detectable electric-fields are ~1.12 V/m and ~3.3 V/m corresponding to a dynamic range of about ~22 dB and ~18 dB at frequencies 10 MHz and 50 MHz, respectively. The sensors exhibit almost linear response for the applied electric-field intensity from 0.29 V/m to 29.8 V/m.

• Journal of the Korea Society of Computer and Information
• /
• v.29 no.9
• /
• pp.137-144
• /
• 2024

Digital advertising, both indoors and outdoors, is evolving from traditional 2D formats to more immersive 3D forms. 3D advertising involves creating 3D content and displaying it through large LED installations on two sides of a building's corner, or using 3D hologram projectors indoors. This study examines the production process of 3D hologram projectors used indoors and LED-based 3D content used outdoors, analyzing potential issues and considerations when creating 3D digital advertising content. The findings reveal that while indoor hologram projector content provides 3D effects, the low resolution of the devices makes it challenging to implement complex content. However, they are cost-effective and easy to operate. On the other hand, LED-based 3D advertising content, produced in high resolution, requires more time for content creation and incurs higher hardware installation costs. Despite this, it effectively represents complex content and maximizes visibility due to its enhanced 3D effects. In conclusion, it is crucial to create tailored content that matches the resolution of the display device to maximize 3D effects in advertising. Specifically, when producing 3D billboard-style outdoor advertising content, the structure of the building on which it will be installed must be carefully considered.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.116-120
• /
• 2013

This paper proposes a novel RF MEMS dc-contact switch with stiff membrane on a quartz substrate. The uniqueness of this work lies in the utilization of a seesaw mechanism to restore the movable part to its rest position. The switching action is done by using separate pull-down and pull-up electrodes, and hence operation of the switch does not rely on the elastic recovery force of the membrane. One of the main problems faced by electrostatically actuated MEMS switches is the high operational voltages, which results from bending of the membrane, due to internal stress gradient. This is resolved by using a stiff and thick membrane. This membrane consists of flexible meanders, for easy movement between the two states. The device operates with an actuation voltage of 6.43 V, an insertion loss of -0.047 dB and isolation of -51.82 dB at 2 GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.40-45
• /
• 1994

The TCAD(Technology Computer Aided Design) software tool is a popular name to be able to simulate the semiconductor process and device circuit. We have developed a two-dimensional TCAD software tool included an editor, parser, each process unit, and 2D, 3D graphic routine that is Integrated Environment. The initial grid for numerical analysis is automatically generated with the geometric series that use the user default(given) line and position separated with grid interval and the nodes corresponding to each mesh point stoic the all the possible attribute. Also, we made a data structure called PIF for input or output. Methods of ion implantation in this paper arc Monte Carlo, Gaussian Pearson and Dual-Pearson. Analytical model such as Gaussian, Pearson and Dual-Pearson were considered the multilayer structure and two-dimensional tilted implantation. We simuttaneously calculated the continuity equation of impurity and point defect in diffusion simulation. Oxidation process was simulated by analytical ERFC(Complementary Error Function) model for local oxidation.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.2
• /
• pp.186-191
• /
• 2006

In this study, five experiments were carried out, with an orifice located downstream of a fan in case I where upstream duct length is 6 D, and that in the downstream is 4 D and different downstream distance to the fan in the rest, so as to determine the optimal location of the orifice and reduce the duct length of airflow measurement device. The resulting flow rate-pressure drop correlations were found to satisfy the limitation of SMACNA standard, which specified an error of $\pm7.5\%$ based on the real flow rate. Also, the best one of five. cases was achieved with the orifice located midway of the orifice duct four times its diameter long.

• Journal of the Korean Society of Radiology
• /
• v.17 no.1
• /
• pp.25-30
• /
• 2023

As 3D printing technology is used in the medical field, interest in metal materials is increasing. The Department of Radiation Oncology uses a shielding block to shield the patient's normal tissue from unnecessary exposure during electron beam therapy. However, problems such as handling of heavy metal materials such as lead and cadmium, reproducibility according to skill level and uncertainty of arrangement have been reported. In this study, candidate materials that can be used for metal 3D printing are selected, and the physical properties and radiation dose of each material are analyzed to develop a customized shielding block that can be used in electron beam therapy. As candidate materials, aluminum alloy (d = 2.68 g/cm³), titanium alloy (d = 4.42 g/cm³), and cobalt chromium alloy (d = 8.3 g/cm³) were selected. The thickness of the 95% shielding rate point was derived using the Monte Carlo Simulation with the irradiation surface and 6, 9, 12, and 16 energies. As a result of the simulation, among the metal 3D printing materials, cobalt chromium alloy (d = 8.3 g/cm³) was similar to the existing shielding block (d = 9.4 g/cm³) in shielding thickness for each energy. In a follow-on study, it is necessary to evaluate the usefulness in clinical practice using customized shielding blocks made by metal 3D printing and to verify experiments through various radiation treatment plan conditions.